Related
Recently tried to flash from JF6 to JH3 and failed. It's now stuck at the phone ! computer screen.
Here's what I've tried so far starting with all the pull sd,sim,batt out and put battery back in:
1. Hold both vol up and down, then plug in usb.
2. Hold both vol up and down, then plug in usb, and then hold power. Let it flash on and off until I get to the 2nd blank screen, then release power.
3. Hold vol up and power, then plug in usb. Let it flash on and off until 2nd blank screen, then release power.
Holding down and power doesn't make the phone!computer flash at all.
I'm really at a loss now. No idea how to get back into download mode... I wasn't able to use the key combos to do it before; just used adb.
Any tips? Help is much appreciated. Thanks in advance.
I've always done after turning off the phone:
1. Plug in USB
2. Hold volume up + down
3. Press and hold power until it turns off for second time then let go (although it's worked for me on the first time it goes off)
Worked every single time for me.
tysj said:
I've always done after turning off the phone:
1. Plug in USB
2. Hold volume up + down
3. Press and hold power until it turns off for second time then let go (although it's worked for me on the first time it goes off)
Worked every single time for me.
Click to expand...
Click to collapse
Doesn't seem to work for me... anything else you can think of?
Have you tied to Flash it with Odin back to stock? Always flash back to stock before flashing. Every thread starts with the same instructions, flash back to stock first. Not to kick you when you're down.
I'd flash back to stock with Odin.
Rhiannon224 said:
Have you tied to Flash it with Odin back to stock? Always flash back to stock before flashing. Every thread starts with the same instructions, flash back to stock first. Not to kick you when you're down.
I'd flash back to stock with Odin.
Click to expand...
Click to collapse
He wouldn't be able to flash without getting into download mode now would he?
op: Make sure that odin is open and ready on your computer. if that doesn't work then i hate to say it but...
Looks like I've got an expensive paperweight? Luckily for me I got it yesterday...
Stupidly enough though, I probably should have returned it in the first place. It wasn't working quite right... I've never seen a phone not respond to button combos or have problems connecting to a computer via USB and I've owned my share of Samsungs. Each boot into their own recovery mode just fine via buttons... guess I won the lottery?
If anyone has some ridiculously convoluted way to get into download mode, I'd be glad to try it.
Did a bit of snooping...
http://forum.xda-developers.com/showthread.php?t=765703
It seems there are a fair amount of phones with disabled button combos...
when i flashed to jh3, i found doing the adb reboot download the easiest way to get into download, even when i messed up my phone and it would boot to galaxy s screen and it would get stuck. Found plugging it in via usb and then running the adb command
Ah... I see. Well, considering I can't get it to recognize it or anything... it's pretty much fubar. I tried my sister's captivate and it boots into download mode just fine with both vol + plug in usb.. so I assume I just had a defective unit that became more defective.
Thanks for the help all, and let's just have this be a lesson to anybody who wants to know, if you follow the instructions on the odin thread and you can't get in, either you're doing something wrong or the phone is wrong...
And adb never hurt anybody.
Thanks again everybody.
pokedoke said:
Did a bit of snooping...
http://forum.xda-developers.com/showthread.php?t=765703
It seems there are a fair amount of phones with disabled button combos...
Click to expand...
Click to collapse
I just exchanged a Captivate for shutting down by itself, got one that can't three button reboot, accidentally bricked it and couldn't recover it. Exchanged it for yet another one that also can't three button reboot. Uggh!
There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
Hi
first of all thank you for so much info.
I spend more than 10 hours looking for a solution on other posts but can't fins a solution.
my phone is bricked and i am not able to get to the download mode or the recovery. before I bricked it I was able to get the download mode with adb with since i tried odin, i have the phone --!-- computer
I am in canada so returning it would be a hassle. any help would be much appreciated to get to the download mode
thank you very much
Download Odin.
Take out the SIM, SD card, and battery. Launch Odin, replace the battery, and plug the USB cord in, and just press down on the volume up and down buttons.
This should boot it right into download mode, then flash with Odin.
This phone is virtually IMPOSSIBLE to brick.
man, i tried that maybe 50 times no kidding!
still no download mode
SeriousBizznass said:
Download Odin.
Take out the SIM, SD card, and battery. Launch Odin, replace the battery, and plug the USB cord in, and just press down on the volume up and down buttons.
This should boot it right into download mode, then flash with Odin.
This phone is virtually IMPOSSIBLE to brick.
Click to expand...
Click to collapse
Hold the volume buttons first then plug in the usb. Thats what works for me. You have to have odin open first like he said.
just tried and still nothing....
if somebody is located in montreal, i would love to meet them to check that out
Athailias said:
Hold the volume buttons first then plug in the usb. Thats what works for me. You have to have odin open first like he said.
Click to expand...
Click to collapse
Having Odin open makes no difference if his button combo is not working. Unfortunately some people are not aware that there phone does not have the 3 button combo working.
what is your solution when you don t have the 3 button combo working?
The only thing you can do if there is no way to reach download mode is to contact At&t or samsung and see if they can repair the phone for you.
Have you tried using a different usb cable, someone mentioned that some USB cables dont work right with the captivate, try the one that came with the phone.
I know odin doesnt matter, but if he is going to flash with odin it helps to have it open first is all I meant. As far as that screen and no three button combo I think you are done... bricked... sorry, dont take my word for it though.
I could enter download mode with key combination before applying Cog's Beta5.5...
I've returned my cappy for exchange.
I am trying with the cable that came with the phone. I don't have another one.
I just bought this phone out of ebay. I will give it this week end to try and find a solution.
I really don't see any as of now but we'll see...
I will try return the phone to the ebay seller as i asked him before buying it if you could go into download mode! and he said yes!
man, I hope i find a solution!
what happens when you try and start your phone normally -- boot screen loop, anything?
Can you get into recovery mode?
when I try to start it normal I get the phone--!--computer
I am sure I tried recovery mode without any success. I am telling I spent so much time on this forum that my wife is going to start being jalous
How do you get to recovry mode again? I tried so many things, that I don't remember
you can't get the phone to be recognized on your computer? Could do ADB to boot into download.
But the battery trick should work.
Pull the sim, external sdcard, and battery.
Hold down the volume buttons and plug in the USB
Then jam the battery back in.
It might take a few times to get it.. but it should get into download mode. I just restored mine doing this trick when it was stuck on this screen.
Really we need to have a youtube vid of this technique
younescito said:
when I try to start it normal I get the phone--!--computer
I am sure I tried recovery mode without any success. I am telling I spent so much time on this forum that my wife is going to start being jalous
How do you get to recovry mode again? I tried so many things, that I don't remember
Click to expand...
Click to collapse
Hold down both volume buttons then hold down the power button until the boot s screen flashes two times then release the power button.
BTW - although it is a LOOOOONG video.. this might help folks out:
http://www.youtube.com/watch?v=iefapF1yZhE&feature=related
Not sure if it will help, but I've also read that you should use the actual motherboard usb ports and not a hub or any kind of "external" ports (i.e. the ports on the front of the tower)
i did all that stuff.
I ended up returning it to the ebay seller who will send me another captivate.
thanks guys
My download was working on cog 2.2 beta before i flashed back to stock using odin. Now when I try to enter download mode i just see the charging symbol. So the only thing that has changed is software. Could odin3 remove my download mode? What can i do?
Its been a rough night for me. I did a Nandroid backup which turned out I needed to restore after something else failed. After restore I did not have what I expected.
Anyway, to make a long story short, I ended up in a situation that no matter what I did, I could not get into download mode. Only recovery.
The good news is that after trying several different things, I finally found I had the original base rom I was using still on the SD card (even though I had done a Master Clear). I guess maybe the only thing that will empty the SD card is to format it.
I have no idea what I would have done had I not had a Clockwork zip on there.
Hello people,
I recently installed GalaxySense Rom (Search "oozeroo" on Google) for my Samsung Captivate AT&T, and it was working fine, until I changed a few settings, then it said it was going to Hot Boot, so the hot boot worked fine. Then, I turned off my phone and turned it back on, and it does not boot. I tried some stuff (check the Situations). My phone is stuck at "Galaxy S Cyanogen(Mod)" (Picture Included!!!)
Situation:
-No Download Mode
-No recovery mode
-Flashed this rom with rom manager (wiped dalvik cache only)
-TRIED installing Clockworkmod recovery, but wont work (not booting into recovery)
-Only an internal SD inside phone, 14 Gigs.
(Ask me for more info if needed please)
Thank you so much, and please help.
--DV
dvasavda said:
Hello people,
I recently installed GalaxySense Rom (Search "oozeroo" on Google) for my Samsung Captivate AT&T, and it was working fine, until I changed a few settings, then it said it was going to Hot Boot, so the hot boot worked fine. Then, I turned off my phone and turned it back on, and it does not boot. I tried some stuff (check the Situations). My phone is stuck at "Galaxy S Cyanogen(Mod)" (Picture Included!!!)
Situation:
-No Download Mode
-No recovery mode
-Flashed this rom with rom manager (wiped dalvik cache only)
-TRIED installing Clockworkmod recovery, but wont work (not booting into recovery)
-Only an internal SD inside phone, 14 Gigs.
(Ask me for more info if needed please)
Thank you so much, and please help.
--DV
Click to expand...
Click to collapse
What key combo are you trying for recovery? You have a JIG laying around? If not, I'd go get one regardless of how invincible you think your phone may be. Maybe you could try Adam's one-click unbrick. http://forum.xda-developers.com/showthread.php?t=1153310 I don't know what conditions need to be met for it (your phone) to be recognized, but I'd give it a shot anyway.
I am using:
take out battery, hold both volume buttons, plug in USB, then put in battery, all with both volume buttons held the whole time.
No, I do not have a jig, I want to get one though
-I do not care to erase everything I have, I tried using Odin3 one click downloader, it worked for me once, when my phone actually went download mode
dvasavda said:
I am using:
take out battery, hold both volume buttons, plug in USB, then put in battery, all with both volume buttons held the whole time.
No, I do not have a jig, I want to get one though
-I do not care to erase everything I have, I tried using Odin3 one click downloader, it worked for me once, when my phone actually went download mode
Click to expand...
Click to collapse
remove sim and microsd. You have to have your batt back in before you hold volume+- and insert USB
what recovery key combo you using?
still nothing buddy, tried your technique
thanks dude
i did try returning it, but they didnt accept it (costco), NOT because I had another romm installed... but because it wasnt booting!
-although, I do not have the battery sign show up, it just has the circle, then it goes to galaxy s screen
Twicebak3d said:
What key combo are you trying for recovery? You have a JIG laying around? If not, I'd go get one regardless of how invincible you think your phone may be. Maybe you could try Adam's one-click unbrick. http://forum.xda-developers.com/showthread.php?t=1153310 I don't know what conditions need to be met for it (your phone) to be recognized, but I'd give it a shot anyway.
Click to expand...
Click to collapse
Dont have linux
post as much as you want on this thread, i dont really care
any other ideas?
Well..... has galaxysense been actually ported to the captivate yet? I doubt this'll work but.... try vol down + home + power. You could vary vol down with vol up for recovery mode as well. Like I said.... doubt they'll work.
It has ported to captivate, there is a captivate section on website
Home button? you mean the touchscreen/virtual home button? When do you press it:when it lights up?
-btw, i tried the brick fix thing, but it didnt recognize my phone, because it was only booting
dvasavda said:
It has ported to captivate, there is a captivate section on website
Home button? you mean the touchscreen/virtual home button? When do you press it:when it lights up?
-btw, i tried the brick fix thing, but it didnt recognize my phone, because it was only booting
Click to expand...
Click to collapse
There's a reason I didn't think it'd work lol. Those are i9000 key combos lol. Get a jig imo.
what are the sgh-i897 combos?
can you go into safe mode with this?
and my home button question please?
dvasavda said:
what are the sgh-i897 combos?
can you go into safe mode with this?
and my home button question please?
Click to expand...
Click to collapse
Yeah I meant that virtual key. cappy combos are vol up/down + power for recovery mode for me.
no recovery for me
actually, at first, I had no recovery on my new rom, so... (I dont want to tell you this!) but I looked for a stock recovery, and I put it over the old recovery file in the system.
dvasavda said:
no recovery for me
actually, at first, I had no recovery on my new rom, so... (I dont want to tell you this!) but I looked for a stock recovery, and I put it over the old recovery file in the system.
Click to expand...
Click to collapse
Do you know if you flashed 3 button? try vol up vol down power. hold those while inserting usb
nothing dude yet, i did not flash the 3 button fix, (oops!)
i did notice that, when the phone is booting up, and I connect, the phone is half recognized with computer, and yes I did install drivers.
If i go to device manager, it says Captivate, but with a yellow exclamation mark
have to go to, talk to you tommorow morning!
thanks buddy, i appreciate it!
dvasavda said:
nothing dude yet, i did not flash the 3 button fix, (oops!)
i did notice that, when the phone is booting up, and I connect, the phone is half recognized with computer, and yes I did install drivers.
If i go to device manager, it says Captivate, but with a yellow exclamation mark
Click to expand...
Click to collapse
I wonder if it'd be recognized by ADB if you install Nexus S drivers. try using that as the drivers for the marked captivate in dev manager. http://developer.android.com/sdk/win-usb.html#
If it changes name to Android Composite ADB interface, then you can ADB into recovery and reflash. I don't see how but if you don't have a jig.... might as well try.
(just raised your thanks meter!)
can I cut off an old charger that fits the captivate, and use that?
dvasavda said:
(just raised your thanks meter!)
can I cut off an old charger that fits the captivate, and use that?
Click to expand...
Click to collapse
For a JIG? Possibly. You have to jump pins 4 and 5 with 300k worth of resistors. if you look in my sig, there's also a guide to just making one without a USB. Regardless of how you apply the resistance to your phone, you still need 301k. There is a window. I've seen 294k jigs work, so just as long as resistance is in a certain range across those two pins, it will work.
ok, thanks
I tried adb rebooting, but says error device not found
(same thing happened when my device was working and on)
I recently got a Captivate for my sister and decided to root it using AIO program from the development section. After rooting the phone and installing CWM I tried to flash Apex 9 ROM. Since I'm used to my Inspire ROMs that will automatically wipe the phone before flashing I flashed it on top of the Stock ROM which resulted on the screen becoming glitchy. Removed the battery and tried to reboot the phone but it just keeps on bootlooping. Tried to start CWM but the phone won't do it. Tried getting into download mode by holding the volume up + down button and plug in the usb cable but it freezes. I'm desperate. Has anyone else experienced something like that before?
guido3300 said:
I recently got a Captivate for my sister and decided to root it using AIO program from the development section. After rooting the phone and installing CWM I tried to flash Apex 9 ROM. Since I'm used to my Inspire ROMs that will automatically wipe the phone before flashing I flashed it on top of the Stock ROM which resulted on the screen becoming glitchy. Removed the battery and tried to reboot the phone but it just keeps on bootlooping. Tried to start CWM but the phone won't do it. Tried getting into download mode by holding the volume up + down button and plug in the usb cable but it freezes. I'm desperate. Has anyone else experienced something like that before?
Click to expand...
Click to collapse
How can I get in straight into CWM? If I could get there I could just wipe the data and flash a different ROM and I know i'd be good. But right now I don't know what else to do
Before you do anything else, stop and read the op for the rom you're trying to flash. Apex 9.x needs GB bootloaders first. Try holding vol down while inserting the usb cord.
If this works, use odin1click and flash back to stock eclair.
Unfortunately, you learned the hard way that flashing a Captivate is different from flashing an Inspire.
Please, for the sake of all of the devs, mods, and more experienced flashers, please read the posts.
And get yourself a jig.
Sent from my GT-I9000 using XDA App
bornjamerican said:
Before you do anything else, stop and read the op for the rom you're trying to flash. Apex 9.x needs GB bootloaders first. Try holding vol down while inserting the usb cord.
If this works, use odin1click and flash back to stock eclair.
Unfortunately, you learned the hard way that flashing a Captivate is different from flashing an Inspire.
Please, for the sake of all of the devs, mods, and more experienced flashers, please read the posts.
And get yourself a jig.
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
Yeah, sucks for me. I tried holding down the volume buttons. It just won't work. All I see is a a round sun, like when a flash website is loading, but nothing else happens. I'm reading about the jig but I already own a cheap micro usb cable, I don't have a solder. Why does it have to be so complicated? In the Inspire when something goes bad you just boot into CWM and do a nandroid restore but in this I can't even access CWM. Just tell me one thing. Is it fixable?
guido3300 said:
Yeah, sucks for me. I tried holding down the volume buttons. It just won't work. All I see is a a round sun, like when a flash website is loading, but nothing else happens. I'm reading about the jig but I already own a cheap micro usb cable, I don't have a solder. Why does it have to be so complicated? In the Inspire when something goes bad you just boot into CWM and do a nandroid restore but in this I can't even access CWM. Just tell me one thing. Is it fixable?
Click to expand...
Click to collapse
It is fixable, it just may take some legwork and a little money.
Have you tried taking out the battery, holding V+/V-, inserting USB cable, and then putting battery back in (that's the alternate froyo/eclair combo)?
If you hold Vol- and power (no USB insertion), you might get download mode (that's the GB combo).
jmtheiss said:
It is fixable, it just may take some legwork and a little money.
Have you tried taking out the battery, holding V+/V-, inserting USB cable, and then putting battery back in (that's the alternate froyo/eclair combo)?
If you hold Vol- and power (no USB insertion), you might get download mode (that's the GB combo).
Click to expand...
Click to collapse
Not working. If I plug the usb I get the damn sun. If I press the power button it will just start booting ove and over again. I think I just screwed up. I just can't understand how flashin a rom can mess up the download mode. Doesn't make any sense.
On I9000 gb bootloaders, volume down + power is download mode
Sent from my Cappy at 1.6 GHz, V6 supercharger, KAK tweaks, and 3G booster using the XDA Premium App!
guido3300 said:
Not working. If I plug the usb I get the damn sun. If I press the power button it will just start booting ove and over again. I think I just screwed up. I just can't understand how flashin a rom can mess up the download mode. Doesn't make any sense.
Click to expand...
Click to collapse
My initial guess is that you may have gotten a phone with the 3-button issue. Before you flashed, were you able to confirm that download mode and CWM were reachable with button combos?
Just to make sure we've covered all the steps, what button combination did you try to use to get to CWM? The only thing I can think that's happening right now is that the kernel you're using is for Gingerbread, and because that's not lining up right, it won't let you get to CWM. That doesn't explain the download mode issue, though, which leads me to believe it may be the 3-button phone issue.
Something you might be able to try is to grab the Android SDK and use the adb tool to force your phone into download mode. It might take a few tries, but it's possible.
The other option is to buy/make a jig. That's pretty much 100% guaranteed to get you to download mode.
jmtheiss said:
My initial guess is that you may have gotten a phone with the 3-button issue. Before you flashed, were you able to confirm that download mode and CWM were reachable with button combos?
Just to make sure we've covered all the steps, what button combination did you try to use to get to CWM? The only thing I can think that's happening right now is that the kernel you're using is for Gingerbread, and because that's not lining up right, it won't let you get to CWM. That doesn't explain the download mode issue, though, which leads me to believe it may be the 3-button phone issue.
Something you might be able to try is to grab the Android SDK and use the adb tool to force your phone into download mode. It might take a few tries, but it's possible.
The other option is to buy/make a jig. That's pretty much 100% guaranteed to get you to download mode.
Click to expand...
Click to collapse
Gosh! 3 buttons issue! What other issues could this phone have? I have the worst luck ever!
I tried all of the buttons combinations: holding volume up and down and pressing power button, volume up only and power button, volume down only and power button. Volume up and down + pluging usb. And same with one button only. I think I might get a jig and go **** myself because this phone got on my nerves. But before, how can I use adb to force the phone into download mode if there is no phone-pc conection at all? The won't even turn on. Would it work if I use it while the sun appears?
guido3300 said:
Gosh! 3 buttons issue! What other issues could this phone have? I have the worst luck ever!
I tried all of the buttons combinations: holding volume up and down and pressing power button, volume up only and power button, volume down only and power button. Volume up and down + pluging usb. And same with one button only. I think I might get a jig and go jig myself because this phone got on my nerves. But before, how can I use adb to force the phone into download mode if there is no phone-pc conection at all? The won't even turn on. Would it work if I use it while the sun appears?
Click to expand...
Click to collapse
I know this is exceptionally frustrating - I've been there myself. All I can say is to be persistent, and you'll get it back to good working order.
When you plug the phone into your computer's usb port, as long as the phone shows some sort of response (even if it's just the charge screen), it's likely to have a connection for data use as well. If you can get your phone bootlooping while you have ADB open, you might be able to issue the "adb reboot download" command in that brief window and get to where you're going without a jig.
One other item to try - One Click Unbrick. With this one, you'd start the phone up bootlooping and run it (I think). With any luck, it might get you somewhere you can get to download mode (or have a wider window with ADB).
And it probably won't work while the sun's showing, as it hasn't really booted up yet, although there's definitely no harm in trying.
i was reading over this and i got my phone into download mode but odin doesnt work
Seikei925 said:
i was reading over this and i got my phone into download mode but odin doesnt work
Click to expand...
Click to collapse
Are you getting your phone to download mode first, then opening Odin on your computer, and then connecting it?
jmtheiss said:
Are you getting your phone to download mode first, then opening Odin on your computer, and then connecting it?
Click to expand...
Click to collapse
Yes i have done that
Seikei925 said:
Yes i have done that
Click to expand...
Click to collapse
Have you tried changing the USB port you're plugging into? It would be best to use one that's directly connected to the motherboard (not on the front of the PC).
Also, are you using a PC, Mac, or Linux machine?
jmtheiss said:
Have you tried changing the USB port you're plugging into? It would be best to use one that's directly connected to the motherboard (not on the front of the PC).
Also, are you using a PC, Mac, or Linux machine?
Click to expand...
Click to collapse
Im using a PC Windows 7, also i cannot boot into CWM, but phone can boot up fine just not recognized by the computer.
Seikei925 said:
Im using a PC Windows 7, also i cannot boot into CWM, but phone can boot up fine just not recognized by the computer.
Click to expand...
Click to collapse
Have you tried reinstalling the drivers on the computer side? If it's not recognizing it at all, that's one possibility. Another is a bad USB cable.
jmtheiss said:
Have you tried reinstalling the drivers on the computer side? If it's not recognizing it at all, that's one possibility. Another is a bad USB cable.
Click to expand...
Click to collapse
Try installing drivers from the AIO toolbox, it worked great for me
Sent from my Cappy at 1.6 GHz, V6 supercharger, KAK tweaks, and 3G booster using the XDA Premium App!
jmtheiss said:
Have you tried reinstalling the drivers on the computer side? If it's not recognizing it at all, that's one possibility. Another is a bad USB cable.
Click to expand...
Click to collapse
Tried re installing drivers several times and have used 4 different USB cables.
Seikei925 said:
Tried re installing drivers several times and have used 4 different USB cables.
Click to expand...
Click to collapse
What Rom/Kernel are you on?
My phone is in the same condition at this moment, and also has the 3 keys combination locked, im w8ing for get a profesional jig because i made one and didnt work. But if the pc recognize the phone u can try with the One click unbrick as jmtheiss said.