Database Develop

time to connect to wifi?

how much time does your kaiser takes to connects to the wifi?? mine takes a hell lot of time sometimes 5 mins even.....i can see in my router logs these 3 points only :
1) Wireless PC connected
2) authenticating.....
3) authentication success
but there is no dhcp lease ip for a long time. I upgraded my router firmware as well....it doesnt take so much time for my laptops (3 of them) what am i missing? any special config i have to do ? or is it possible to se the debug logs for my kaiser so i can try to find out the root cause?

My kaiser takes about 10-15 seconds with my Linksys WRT54G using WPA-TKIP. I'm running the stock HTC ROM and have nothing special setup.

4 seconds
no WEP
mac address filter: only allow selected mac addresses

After really looking at this, like the below user says, it takes less than 5 seconds with WPA-TKIP and MAC filtering. 5 minutes is excessively long, but unfortuntaly it seems that you've done everything I can think of. Hope you can find a fix!

Do you have the WiFiRouter installed? It may be falsely trying to connect to itself.

yes i have the dlink Dl 524.....it works fine with other laptops and even my kaiser gets connected to it...but it take a hell lot of time.....

gandotratushar said:
yes i have the dlink Dl 524.....it works fine with other laptops and even my kaiser gets connected to it...but it take a hell lot of time.....
Click to expand...
Click to collapse
I think Nick meant, do you have WMWiFirouter installed on your kaiser (the app by Chainfire) as the kaiser may be trying to connect to itself.
One other thing, is your SSID on the router 'Hidden'? If you have not selected the box for hidden network on Wireless connection (when you set it up on the kaiser) it can bit 'Hit n Miss' to get a connection.

just config the router to do mac filtering. Theres practically no authenticating step, it just goes like this:
1)This device is trying to connect, does it match the mac addresses owner provided?
if no -> user cannot connect
if yes-> user connects
// this is assuming you click the option "allow selected devices..."
only bad thing about mac filtering is that if you have a new device that making a new mac key for it is a nuisance.
otherwise, you can forget all those security keys!
*btw* if router signal is roughly below 20% it may take a while to connect, you may want to use 3rd party wifi managers like wififofum.

nothing works...i gets the same problem ...it takes a hell lot of time to connect.....is there any 3rd party software which can help me connecting to the network. I have noticed that it gives me the wrong signal strength as well.....sitting just next to the router it gives shows 60-70% signal strength. i dont have wifirouter app installed. I have tried the mac filtering as well but didnt help. my network is broadcasting the ssid and is not hidden.....and i am hating this. my friend wanted my kaiser to connect to his network so he could browse but it never got connected and i felt ashamed of this ~500 pound phone ......

did you try changing the power mode to best performance?

Mine takes 7 seconds to connect every single time. Thomson speedtouch from be broadband.Wep encryption.

ekw said:
just config the router to do mac filtering. Theres practically no authenticating step, it just goes like this:
1)This device is trying to connect, does it match the mac addresses owner provided?
if no -> user cannot connect
if yes-> user connects
// this is assuming you click the option "allow selected devices..."
only bad thing about mac filtering is that if you have a new device that making a new mac key for it is a nuisance.
otherwise, you can forget all those security keys!
*btw* if router signal is roughly below 20% it may take a while to connect, you may want to use 3rd party wifi managers like wififofum.
Click to expand...
Click to collapse
It should probably be noted that this isn't a very secure method. But if you're not worried about your traffic being sniffed or someone cloning your MAC and getting on your network. Go for it!

joshuah82 said:
It should probably be noted that this isn't a very secure method. But if you're not worried about your traffic being sniffed or someone cloning your MAC and getting on your network. Go for it!
Click to expand...
Click to collapse
i have tried this as well. sometimes it works. and i have set it to best performance. still no good

It takes 4 seconds for me (with a Linksys AP/Router) with WPA TKIP authentification.
Have you tried different wifi channel ? Have you try "Wififofum" to have some info about you're AP ?

my router is running with channel 11 ....how can i put it in my kaiser? what channel is yours running on?

That is extremely unsecure and not a good idea. A MAC spoof is such a simple thing so others can get right on your network...never mind the fact that all of your data is flying around in plain text.
Some one with a laptop/mac spoof and ettercap will wreck your stuff bad.
ekw said:
just config the router to do mac filtering. Theres practically no authenticating step, it just goes like this:
1)This device is trying to connect, does it match the mac addresses owner provided?
if no -> user cannot connect
if yes-> user connects
// this is assuming you click the option "allow selected devices..."
only bad thing about mac filtering is that if you have a new device that making a new mac key for it is a nuisance.
otherwise, you can forget all those security keys!
*btw* if router signal is roughly below 20% it may take a while to connect, you may want to use 3rd party wifi managers like wififofum.
Click to expand...
Click to collapse

laakness said:
That is extremely unsecure and not a good idea. A MAC spoof is such a simple thing so others can get right on your network...never mind the fact that all of your data is flying around in plain text.
Some one with a laptop/mac spoof and ettercap will wreck your stuff bad.
Click to expand...
Click to collapse
but atleast it should work...

If only we could all think like that

I use WRT54G running DD-WRT (custom linux firmware wich is a bit more stable than the original linksys fw) with WPA2-PERSONAL (AES) and it takes about 4 sec to connect. I live on 4th floor and the router is on 3rd floor.
TyTN II manufactured in oct07, original ROM.

Wireless Wierdness

Help!
I have a Netgear DG834T router as provided by Sky. I have one wired and two wireless connections running into it (let's call them WD, WL1 and WL2 respectively).
On the connections page I can see all of them under "attached devices"...but now I want to connect using my Kaiser (actually an O2 XDA Stellar)
What happens...
On the Kaiser, I get an IP address (assigned by DHCP) as normal - but can't access the internet - or at least, can only access it very rarely - http://www.google.com can't be found, but http://www.bbc.co.uk can. No idea why.
On the router, under "attached devices", not only can I NOT see the Kaiser, but WL1 and WL2 also disappear. WD remains visible. The router cannot ping the IP address of the Kaiser (timed out). If I disable WiFi on the Kaiser, then WL1 and WL2 are immediately visible again. Internet connection on WL1 and WL2 works, even when they are not visible.
I HAVE connected to this network before without any problems.
What the hooting heck is going on, and how do I fix it?
Thanks!

Time to troubleshoot! What happens with this phone on another wireless network. We need to determine if it's the phone or the network. Do you have any friends with a phone like this? Can you use their phone on your network? Do you have any ROMs flashed, has this phone ever been on the network without problems?
If the phone works on another router try looking for firmware updates for the router. Those things really do need to be updated often and it could have something to do with that.

Only have access to one network :-(. Might be a couple of weeks before I can access a hotel one or something like that.
Think next door neighbour has similar phone, but different provider...will try if he'll let me!
No ROMS flashed.
It connected fine when I first had it. As far as I know, I've changed nothing since then.
2 out of 4 answered...with an option on three...I'll get back to you as soon as I've beaten up my neighbour and stolen his phone...
Joke!

There should be somewhere you can go to test that wireless. I can walk outside the building I'm in and find one.

ChumleyEX said:
There should be somewhere you can go to test that wireless. I can walk outside the building I'm in and find one.
Click to expand...
Click to collapse
You = US, me = UK. We still think the biro is a recent invention...

Neighbour's phone on my network gives the exact same problem. I've also noticed that when I click "Renew IP" on the Kaiser it doesn't work...it gives me 0.0.0.0, but will occasionally flash up the correct IP address. It's alomst as if the connection is being lost and remade every few seconds. The status ist gives me is "associated to network"...is that different to "connected"?
I've been trying to solve this on my router, but none of the settings seem to make any difference.

Same here
I get the same with the router from sky.
Kaiser says I have an IP address, 192.168.0.5, but the it doesn't show up on the attached devices on the router.
What I find that works is hit renew IP maybe twice until you get a really wierd IP address like
169.254.*.**, actually not sure if I'm picking up another network, but for some reason I don't think I am.
I can then browse the web and sync via wifi.
Really pisses me of that it says that it has an IP address but doesn't connect.

1) Make sure you dont have a proxy set up on your wifi connection on your device.
2) The 169. address is your device getting an unauthorised IP address as the router did not receive the correct encryption key from the device.
3) You can check if its an encryption thing by simply logging in to the router (192.168.0.1 in your web browser on pc) and changing the settings to turn wpa off and testing it. The routers username and password are on the card - its something like "sky" and "admin"

Yeah I agree, there is something up with that router.

Grey Area said:
Neighbour's phone on my network gives the exact same problem. I've also noticed that when I click "Renew IP" on the Kaiser it doesn't work...it gives me 0.0.0.0, but will occasionally flash up the correct IP address. It's alomst as if the connection is being lost and remade every few seconds. The status ist gives me is "associated to network"...is that different to "connected"?
I've been trying to solve this on my router, but none of the settings seem to make any difference.
Click to expand...
Click to collapse
with my router.....i have to set the wifi power mode on my kaiser to "best performance", any other setting and i get that "associated to network" ****. been this way every since the hermes and the wizard.

unwired4 said:
1) Make sure you dont have a proxy set up on your wifi connection on your device.
2) The 169. address is your device getting an unauthorised IP address as the router did not receive the correct encryption key from the device.
3) You can check if its an encryption thing by simply logging in to the router (192.168.0.1 in your web browser on pc) and changing the settings to turn wpa off and testing it. The routers username and password are on the card - its something like "sky" and "admin"
Click to expand...
Click to collapse
No, proxy set-up as the device was bought unbranded in US.
Because there are issues with this router, encryption and media streaming devices, I have only restricted the mac addresses with no encryption.
Still don't know about the 169. ip address beacuse doesn't seem to come up as am ISP.

Now then, how wierd is this?
After all these issues and kind of giving up on it as a bad job, I also noticed that out on the road, my GPRS wasn't working either - TomTom couldn't connect to the "plus" traffic service.
I get on the phone to O2 who told me that my phone hadn't been "provisioned". After one false start where they didn't seem to do anything about it, I have just (literally) had them tell me to go to the O2 Operator settings and tell it to update the "O2 UK Post Pay_GPRS" and reboot.
GPRS now works. And magically, so does my WiFi - IP address negotiated and full access to internet and my router's setup page granted. Working like a charm again.
So - seems to me it's an account setting, and nothing to do with either me poor ol' router or me nice new phone.
For completeness, I was occasionally getting the 169 IP address too, so it sounds like we have EXACTLY the same problem - suggest you get onto your service provider ASAP.

gprs connection failed

It worked yesterday but now won't. If I enter proxy settings into orangeinternet acp the same as orangewap then it works for http traffic but not email.
I have done a lot of setting up on the phone since it arrived yesterday but I can't think what I can have altered in the gprs settings.
I had the same issue with my Touch Cruise on the newer ROMs and it went away when I reverted to the official HTC Cruise 6.1 ROM.
Any ideas anyone?

You could always try running the network setup wizard again?

You could always try running the network setup wizard again?
Click to expand...
Click to collapse
I tried that several times - it doesn't work. I think it must be a screwed setting from setting up something like exchange server in activesync.
Everything works under wifi.
I am really hoping I don't have to do a hard reset and start all over again.

Try putting a different operator's sim in and let it set everything up for it, then put your orange sim back in and go through the auto setup again. If that doesn't work then a hardreset might be your only option. Going from your other posts in the themes, applications and software it looks like your phone is really playing up so a hardreset might be best all round, only install one thing at a time and test everything after every install and customisation until you find out what you're doing to break it, then don't do that step again.

Have you messed around at all under the network advanced options where you set things like HSDPA etc

Thanks for all the replies. I've ended up hard resetting and re-customising one thing at a time.
The thing that breaks it seems to be when I change the wifi settings. I have a non-standard wireless network at home and I have to specifiy the IP address and default gateway in the "network adaptors" settings for wifi. Once I access the network with these settings it breaks the cellular data connection!
Like I said earlier, my Cruise did this as well with the later ROM such as Udk's and C_Shekhar's. When I went back to the official HTC 6.1 ROM everything worked fine.
I have now reverted my wireless settings to standard (i.e. DHCP) and it has restored the cellular connection but, obviously the wifi doesn't work.
If I can't sort this I'll have to rethink my home network.

Sounds like you're using set IP addresses on your home network for port forwarding or something of that nature. Have another look in your router's settings as most decent ones will allow you to reserve IPs from the DHCP range for specific MAC addresses, that way when the computers or other devices ask for an IP they get given the same one every time. Things really do work much more smoothly as far as networking goes when DHCP is working. If you really do need to specify IP addresses manually then just let the router hand out addresses by DCHP from a restricted range, e.g. if you manually specify addresses from 192.168.1.2 to 192.168.1.10 then set the start address for DHCP to 192.168.1.11.

Thanks, shuflie. It's actually to do with the default gateway. I have an orange livebox doing the adsl work so I can plug a telephone in to it to get free calls. However, the wireless is useless on the livebox so I have a netgear wireless router on the network as well. The trouble is, DHCP won't work that way so I have to set each wireless device up with a dedicated IP address and direct it to the livebox as the gateway.
For some unknown reason, this breaks cellular data on winmo devices.
Anyway, until I find a solution I have removed the orange livebox from my system. I'll just have to live without the broadband phonecalls which is no big deal tbh.

I actually run a non standard network here too, a SKY ADSL router to provide the broadband access and a Netgear router which all my computers attach to. Both router are set up as DCHP servers, but the SKY box only gives out an address to the Netgear router, the Netgear hands out the IP addresses for everything else. The only drawback I've seen so far is that it seems impossible to initiate a connection from the outside world to any of the computers on my network because of the dual NAT that is happening, but that isn't necessarily a bad thing as it makes it harder to hack in from outside. I don't have to point the computer and other devices to the SKY box as the gateway, I just let the Netgear router think that the connection it is getting from the SKY box is a direct connection to the outside world. Everything seems to work just fine, no problems with network gaming on the playstation network and torrents, skype, web etc. seem to work just fine. If you can't live without the broadband calls you could give it a go.

Should have said that the SKY and Netgear routers are on different subnets, 192.168.0.x for the SKY and 192.168.1.x for the netgear.

Can't connect my N1 with Linksys router

Hello
My N1 can connect easily to all kind of wifi routers and modems without problem but not with my fitness club's one, they have a Linksys N160.
My N1 can detect the signal,enter the password but then it's stucked with the message ''getting ip...''
Where is the problem? is it a know hardware or software compatibility stuff?

Sometimes rebooting the wifi router helps. Also make sure that when the guy over at your fitness club reboots the router you don't have the wifi of the club saved. delete the saved wifi profile, reboot the wifi router and then try. Cheers.

Already tried it several times. I saw that OS4 of iphone/ipod have the same problem with router enabling Wireless-N, I will ask him to limit the router to B/G

I also had similar problem with Linksys WAG54G2 (at latest firmware). Then I changed to much cheaper adsl router, TP-LINK WD-W8960N and no more connection problem.
Sent from my Nexus One using XDA App

I had problems using my Nexus One on my SMC Barricade 802.11b/g/n router when 802.11n was enabled. Turned it off; problems were gone. I don't think that works well yet, though some people have said otherwise. Could be a router-specific issue.

Ok so it's a WAG160N to be specific.
He tried to use mixed B/G instead of mixed (which would imply N too) but it still stuck at getting ip...
I told him to throw this router in the garbage because anyway SE and HP mobiles can't connect too,but he said he would do it but his boss will never accept to pay a penny more

My parents had a router that did exactly the same, my phone got stuck on Obtaining IP, whilst the missus 5800 connected and broswed just fine.
It was a crappy old thing and they replaced it the other week, now I can connect and browse just fine.

I also use a linksys WAG160N.
bought a nexus one, could not for the life of me get an internet connection.
turns out dns on router is poofed, so i just set DNS from my isp manually on the nexus one together with a static ip and booya interent at full 802.11n speeds.
sometimes its the simple things.

This sounds similar to when I set my router to channel 13 or whatever the max was on it. My N1 would only sometimes get a connection, but would eventually drop it and stay off. Solved it by selecting a lower channel (WifiAnalyzer suggesten channel 1 as the best alternative to channel max) on the AP.
I can see that in CM6 nightly that I have since started using I can choose regulatory domain, and thereby open up channels previously blocked. If you can't change anything on the AP this might help you solve the problem on your end.
So suggestions if none of the posts above me provide a solution is to run WifiAnalyzer and see how the channel-graph looks.

Chromecast will not connect to my TELUS ROUTER

Chromecast wont connect to my telus router (Actiontec V1000H). I can't see any option to enable/disable AP Isolation. Is there any solution for this?
fixed:laugh:

2237 9525694
mydrl said:
Chromecast wont connect to my telus router (Actiontec V1000H). I can't see any option to enable/disable AP Isolation. Is there any solution for this?
fixed:laugh:
Click to expand...
Click to collapse
How?

try changing the wifi channel the router uses

mydrl said:
Chromecast wont connect to my telus router (Actiontec V1000H). I can't see any option to enable/disable AP Isolation. Is there any solution for this?
fixed:laugh:
Click to expand...
Click to collapse
How did you fix this?

MadBob said:
try changing the wifi channel the router uses
Click to expand...
Click to collapse
Good advice.
Remember that the WiFi bands (channels) are not exactly the same between countries. So if you're in a non-US country and your router happens to choose a channel that is not available in the US, Chromecast may not detect your wireless AP.

But Telus is Canadian, and Canada has the same WiFi channels as the U.S. (Canada and the U.S. necessarily share identical radio spectrum allocation).

DJames1 said:
But Telus is Canadian, and Canada has the same WiFi channels as the U.S. (Canada and the U.S. necessarily share identical radio spectrum allocation).
Click to expand...
Click to collapse
Didn't know that. Thanks! Still applies to other countries though. I think Channel 13 is one of the channels that applies to Europe but not US. I should put it in the FAQ...
EDIT: Seems there's far less exclusion than I thought... but added a note in the FAQ just in case.
http://en.wikipedia.org/wiki/List_of_WLAN_channels

So I can get through the setup phase up until the Chromecast tries to connect to my wifi network. I get a message saying it couldn't connect, and when I click the link in the message it brings me to a page that mentions AP filtering, UPNP enabling and .NET 3.5. I checked and UPNP is enabled, and I can't find an option for AP filtering (I have the Actiontech V1000h). I am using a Macbook pro.

Kipp34 said:
So I can get through the setup phase up until the Chromecast tries to connect to my wifi network. I get a message saying it couldn't connect, and when I click the link in the message it brings me to a page that mentions AP filtering, UPNP enabling and .NET 3.5. I checked and UPNP is enabled, and I can't find an option for AP filtering (I have the Actiontech V1000h). I am using a Macbook pro.
Click to expand...
Click to collapse
In some cases you have to go through a couple of times. I just reset my Chromecast to test a few things and had to go through the setup twice before it connected to my WiFi.

Chromecast in Canada, on Telus
A friend lent me his chromecast. He uses an iphone and Shaw cable. I use a Nexus 4, and have Telus as my internet provider.
It was a bear trying to get chromecast to work. Tried 5 separate days. Got it to work and i could watch netflix/youtube on it about 3 times and played with it for a couple of hours each. That's the success.
The fail is that I had to trouble shoot more then 4+ hours to get it to work those 3 times. Reboot the chromecast. Reboot the router. Reboot my Nexus 4. Try my wife's Nexus 4. Try the Nexus 7 tablet. It was a horrible experience. I got the AP recommendation like the earlier post in this thread. I tried that. Tried calling telus and signed into my router to check that those settings were correct. As far as I understand it's a gateway 11n wireless router.
So my conclusion is change my internet provider to Shaw unless someone has a smart solution to this problem. The router says it's a 50ghz signal? So it isn't the 2.4vs 5.0 ghz signal problem that I've googled and read about.
Please provide some brains to my situation. I've used all of mine up.
bhiga said:
In some cases you have to go through a couple of times. I just reset my Chromecast to test a few things and had to go through the setup twice before it connected to my WiFi.
Click to expand...
Click to collapse

Still not fixed.
So I took the plunge and bought one. Maybe it'd be different than my friends. Looks like this is a me problem. The chromecast still doesn't work. I thought it might be the tv that it's plugged into? Maybe shielding the chromecast from the wifi? I don't know. Will trouble shoot with a different tv or a long hdmi cable that will get the chromecast out from behind the tv. Maybe that'll help.

johnson2423 said:
So I took the plunge and bought one. Maybe it'd be different than my friends. Looks like this is a me problem. The chromecast still doesn't work. I thought it might be the tv that it's plugged into? Maybe shielding the chromecast from the wifi? I don't know. Will trouble shoot with a different tv or a long hdmi cable that will get the chromecast out from behind the tv. Maybe that'll help.
Click to expand...
Click to collapse
TVs are great at blocking/scrambling radio signals.
Use the included HDMI extender. If that doesn't help (enough), get an HDMI extension and move Chromecast away from the TV. One of mine is on a 10-foot HDMI extension. The other is connected upstream of a another device that connects to my TV, so both of my Chromecasts are at least a foot away from its associated TV.

johnson2423 said:
So I took the plunge and bought one. Maybe it'd be different than my friends. Looks like this is a me problem. The chromecast still doesn't work. I thought it might be the tv that it's plugged into? Maybe shielding the chromecast from the wifi? I don't know. Will trouble shoot with a different tv or a long hdmi cable that will get the chromecast out from behind the tv. Maybe that'll help.
Click to expand...
Click to collapse
It could be a few things not related to the router directly but related in how the Router connects to your ISP.
So a couple of questions...
What kind of service is your ISP? (DSL, CABLE, OTHER)
What Public IP does your router report? (Usually found on the status page that shows connection data) If it starts off 192.168 then your Modem is doing a double nat translation and you need to call your ISP and tell them you want the Modem to be put into gateway mode and just pass a public IP to your router.
Does the CCast actually connect to the Router but not work or will it not connect at all period? If it doesn't connect at all it is possible you need to change the Security method used to WPA or WEP. To test shut off security alltogether and try to connect the CCast. If there is currently NO security try putting WPA on and trying again (but it should work on an open AP)

fixed...
Asphyx said:
It could be a few things not related to the router directly but related in how the Router connects to your ISP.
So a couple of questions...
What kind of service is your ISP? (DSL, CABLE, OTHER)
What Public IP does your router report? (Usually found on the status page that shows connection data) If it starts off 192.168 then your Modem is doing a double nat translation and you need to call your ISP and tell them you want the Modem to be put into gateway mode and just pass a public IP to your router.
Does the CCast actually connect to the Router but not work or will it not connect at all period? If it doesn't connect at all it is possible you need to change the Security method used to WPA or WEP. To test shut off security alltogether and try to connect the CCast. If there is currently NO security try putting WPA on and trying again (but it should work on an open AP)
Click to expand...
Click to collapse
Service is Telus DSL.
Solution: I changed the security settings. It still tries to stop the CCast from talking to my phone once in a while, but I just log into my router and log into the firewall settings. The firewall settings are "high, medium, low, NAT". It started working once I started turning it off of NAT and onto Medium or High.
I don't know why this is the solution, but it is a solution. I suspect that either Telus will fix the prolbem for everyone else or this thread will become popular. Now CCast is coming to Canada. So either Telus fixes it or there'll be a lot of searching leading to this post.
As a reminder, a friend of mine on telus never toughed his firewall settings and never had a problem with using his CCast. Go figure.

johnson2423 said:
Service is Telus DSL.
Solution: I changed the security settings. It still tries to stop the CCast from talking to my phone once in a while, but I just log into my router and log into the firewall settings. The firewall settings are "high, medium, low, NAT". It started working once I started turning it off of NAT and onto Medium or High.
I don't know why this is the solution, but it is a solution. I suspect that either Telus will fix the prolbem for everyone else or this thread will become popular. Now CCast is coming to Canada. So either Telus fixes it or there'll be a lot of searching leading to this post.
As a reminder, a friend of mine on telus never toughed his firewall settings and never had a problem with using his CCast. Go figure.
Click to expand...
Click to collapse
Well if the Telus was set to NAT perhaps Double Nat Translation was the issue.
DO you have another router connected to your modem or is this one of those all in one Hybrids supplied by the ISP?

Asphyx said:
Well if the Telus was set to NAT perhaps Double Nat Translation was the issue.
DO you have another router connected to your modem or is this one of those all in one Hybrids supplied by the ISP?
Click to expand...
Click to collapse
I have a friend that is struggling with this as well. While setting up the WiFi connection between the chromecast and the router (the Actiontec V1000H - which is a modem/router combo if that helps). The chromecast will see the WiFi, but it seems to time out while trying to connect to the router.
I did find a comment on a blog somewhere (sorry, I forget where) that suggests unchecking the "IGMP snooping enabled" option in the router (Advanced Settings>IGMP Setting). Once this was done, the chromecast connected to the WiFi without any issues and we were able to stream it without any issues.
However after going out for dinner we had major issues trying to connect to the WiFi on our phones and his laptop (laptop would try to connect to the WiFi but continually fail). It seems like this is a temporary fix at best.
The only permanent solution I can think of at the moment is to go buy a new router that is listed as having no issues on the chromecast compatibility list... Which kind of defeats the whole purpose of having the chromecast as an economic way to stream content to your big screen.

Buy a better router

I don't see why IGMP should have any affect on being able to login and connect.
I Can see it being a problem with streaming but not connection.
IS this an ISP provided Modem/Router? How many devices are connecting wirelessly?
Check settings for IGMP Proxy, Try changing that setting whatever it is but it should probably be disabled (Still don't think this would affect connection but it's worth checking)
Check if UPnP Is enabled (again not really connection related but it does need to be enabled for CCast)
I personally prefer to use a two device setup with separate Modem (in Bridge Mode) and Router....This way the Modem protects the router from the outside world and even if the Modem goes bad the Network still functions properly.
And I pretty much stay away from anything that isn't a Linksys or Netgear product as far as Routers are concerned.
There are a bunch of Actiontec models that are listed as incompatible with CCast on the google site so it's obvious that something about their firmware is not CCast friendly.
So the the previous poster may actually have made a good suggestion in the long run! LOL

I'm using the telus actiontech router with chromcast with no issues....
its a pretty crappy router though and it seems telus disabled the ability for bridge mode in the latest firmware... has anyone found a solution to this so i can buy a better router?
Sent from my Nexus 7 using Tapatalk

nolook said:
I'm using the telus actiontech router with chromcast with no issues....
its a pretty crappy router though and it seems telus disabled the ability for bridge mode in the latest firmware... has anyone found a solution to this so i can buy a better router?
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
As long as double NAT doesn't cause you problems, you can
Assign the new router's WAN port to an address in the ISP router's LAN range
Set the new router's gateway to the ISP router's LAN address
Connect the two routers LAN port to LAN port
Have all your wired and wireless clients connect to the new router.