C6603 Stuck in bootloop! [Last update: 24/1/14]
UPDATE 24/01/14
This issue has been SOLVED.
I replaced the battery with one from eBay and the phone is working flawlessly, all the ROM flashing I went through was not the problem at all. Remember that if you are going to try to replace the battery you may as well buy a new rear glass piece as it is almost guaranteed that the glass will break in the removal process. You will also require new a adhesive piece. The entire procedure cost me $51AUD (battery, glass, adhesive).
All the content below is irrelevant, if your phone randomly shuts off (instantaneously) on boot or soon after, try to replace your battery!
Thanks for your help.
I've got quite a story to tell and if you have the patience to read it, I will greatly appreciate your assistance. TL;DR BELOW
In the beginning I was running 4.2.2, on a stock Australian 10.3.A.0.423 Unbranded ftf. It had been working flawlessly for a month or so until quite recently. It had developed a problem where it would only remain switched on whilst being plugged into the wall socket. As soon as (or thereafter) I removed the plug out of the phone, with one touch, one action, BAM! The display was off and I had to restart the phone again. I spent a few hours browsing for solutions to this problem, most of them said to hold the power and vol+ buttons until the handset vibrated 3 times. That turned it off alright, but I'm looking to go in the other direction.
After a stressful while scrounging old forum posts, I came to the conclusion that the fault is in my ROM, after all, I had flashed from 4.1.2 (I think) to 4.2.2 just a month prior (I flashed a ROM instead of waiting until the snail-like carriers here in Australia decided to dribble out the release). So now being convinced that I ROM is at fault I browse XDA for a newer stock one. Hey! Look! 4.3 it being rolled out in Aust, I check whether it's available to me yet, and obviously, no, it is not. I stumble upon this thread in my travels. I spend a while working to meet it's requirements. Get flashtool, get unlocked bootloader, get root, install cwm, and attempt to install XzDualRecovery 2.6. I've placed the XDR.zip on the sdcard in the XZ, I run the zip using CWM, it seems successful, I then go to reboot and check whether my 4.3 works, after I select reboot I'm asked whether I wish to root the phone. Why yes! that seems easy enough, and just as I select 'ok' the screen goes blank. The bloody phone has switched off in the middle of my work! I try to boot and it hangs on the Sony logo then reboots, creating a cycle. I decide to plug it back in to the wall socket (as this is the only way to get it to boot and remain on), huzzah, it runs. But the root had failed. The rest of my rant is insignificant until now (around 7 hours of failed attempts later)
So in an attempt to keep this wall of text down, I try my best to summarize, If I am not clear enough, just say.
I tried reflashing my old 4.2.2 ROM back, this makes the whole thing worse, now the phone won't even get past the Sony logo (even when plugged to a socket), I flash a different 4.3 ftf, nothing, I restore with PCC, I restore with SUS, I create a ftf from the SUS files and attempt to flash that. Nothing, nothing works. So where am I at now?
The phone still has battery, although, I'm not sure how much, I can no longer get it to charge as it hangs on the Sony logo. The phone should be flashed with 10.3.A.0.423, but when I check the baseband version in Fastboot cmd prompt, it still says 10.4.B.0.569, I feel as though flashtool isn't flashing properly, but I've read that this is usually a non-issue. I can boot into flashmode and fastboot mode. I can unlock and lock the bootloader. I can use ADB and Fastboot CMD (Minimal version) to read values and run commands. Actually, I managed to use the phone in fastboot mode, in conjunction with ADB and Fastboot CMD, I ran the command "fastboot continue" and the phone went on to charge off the usb power, It didn't seem to charge very fast, or at all, and I haven't been able to get it to do it again. So a TL;DR:
-C6603 stuck in bootloop.
-Possibly has a 4.2.2 ROM installed (10.3.A.0.423 Unbranded AU)
-Cannot Charge
-Can run flashmode and fastboot mode
-Can use ADB and Fastboot
-Can use SUS, PCC, and Flashtool to flash stock roms
-Can't figure this out for the life of me!
UPDATE 01/01/14
Currently I have a kernel installed that allows me to use cwm twrp (doomkernel v19, maybe), I have flashed a 'flashable' stock 4.3 rom using cwm and the phone didn't manage to get past the kernel logo. HOWEVER, using fastboot mode, I run the command "fastboot continue", and if I allow the phone to go past the kernel logo it vibrates, the LED turns green as opposed to showing a purple one, and it will begin charging (The LED isn't green as a result of the battery level). EDIT [1/1/14 3:01AM]: I tried to launch the phone whilst it was charging, the charging symbol went away and the phone remained on a black screen (lcd is on, but nothing is displayed) for a few seconds before shutting off automatically.
I must mention, I cannot get into recovery unless I boot the phone into fastboot mode, run the command in fastboot: "fastboot continue". If I don't do this, it simply crashes (shuts off) when showing the kernel logo.
If you need to know more I will provide as much information as I can, as succinct as I can, as fast as I can. I am in this for the long run. Thank you for your time,
UPDATE 08/01/14
I've come to the conclusion that my issue is battery related. After repeated from flashes and fastboot attempts, I managed to get the phone charging a few times, I witnessed the level was sporadic upon infrequent viewings. I have come across a few other very similar threads and feel that it is necessary to try replacing the battery, I try and post a youtube clip that details what happens currently.
Keringkien
keringkien said:
C6603 Stuck in bootloop!
I've got quite a story to tell and if you have the patience to read it, I will greatly appreciate your assistance. TL;DR BELOW
In the beginning I was running 4.2.2, on a stock Australian 10.3.A.0.423 Unbranded ftf. It had been working flawlessly for a month or so until quite recently. It had developed a problem where it would only remain switched on whilst being plugged into the wall socket. As soon as (or thereafter) I removed the plug out of the phone, with one touch, one action, BAM! The display was off and I had to restart the phone again. I spent a few hours browsing for solutions to this problem, most of them said to hold the power and vol+ buttons until the handset vibrated 3 times. That turned it off alright, but I'm looking to go in the other direction.
After a stressful while scrounging old forum posts, I came to the conclusion that the fault is in my ROM, after all, I had flashed from 4.1.2 (I think) to 4.2.2 just a month prior (I flashed a ROM instead of waiting until the snail-like carriers here in Australia decided to dribble out the release). So now being convinced that I ROM is at fault I browse XDA for a newer stock one. Hey! Look! 4.3 it being rolled out in Aust, I check whether it's available to me yet, and obviously, no, it is not. I stumble upon this thread in my travels. I spend a while working to meet it's requirements. Get flashtool, get unlocked bootloader, get root, install cwm, and attempt to install XzDualRecovery 2.6. I've placed the XDR.zip on the sdcard in the XZ, I run the zip using CWM, it seems successful, I then go to reboot and check whether my 4.3 works, after I select reboot I'm asked whether I wish to root the phone. Why yes! that seems easy enough, and just as I select 'ok' the screen goes blank. The bloody phone has switched off in the middle of my work! I try to boot and it hangs on the Sony logo then reboots, creating a cycle. I decide to plug it back in to the wall socket (as this is the only way to get it to boot and remain on), huzzah, it runs. But the root had failed. The rest of my rant is insignificant until now (around 7 hours of failed attempts later)
So in an attempt to keep this wall of text down, I try my best to summarize, If I am not clear enough, just say.
I tried reflashing my old 4.2.2 ROM back, this makes the whole thing worse, now the phone won't even get past the Sony logo (even when plugged to a socket), I flash a different 4.3 ftf, nothing, I restore with PCC, I restore with SUS, I create a ftf from the SUS files and attempt to flash that. Nothing, nothing works. So where am I at now?
The phone still has battery, although, I'm not sure how much, I can no longer get it to charge as it hangs on the Sony logo. The phone should be flashed with 10.3.A.0.423, but when I check the baseband version in Fastboot cmd prompt, it still says 10.4.B.0.569, I feel as though flashtool isn't flashing properly, but I've read that this is usually a non-issue. I can boot into flashmode and fastboot mode. I can unlock and lock the bootloader. I can use ADB and Fastboot CMD (Minimal version) to read values and run commands. Actually, I managed to use the phone in fastboot mode, in conjunction with ADB and Fastboot CMD, I ran the command "fastboot continue" and the phone went on to charge off the usb power, It didn't seem to charge very fast, or at all, and I haven't been able to get it to do it again. So a TL;DR:
-C6603 stuck in bootloop.
-Possibly has a 4.2.2 ROM installed (10.3.A.0.423 Unbranded AU)
-Cannot Charge
-Can run flashmode and fastboot mode
-Can use ADB and Fastboot
-Can use SUS, PCC, and Flashtool to flash stock roms
-Can't figure this out for the life of me!
If you need to know more I will provide as much information as I can, as succinct as I can, as fast as I can. I am in this for the long run. Thank you for your time,
Keringkien
Click to expand...
Click to collapse
download any FTF , 4.2.2 or 4.3 , connect your device to flash tool as flashmode , and select to flash the ftf , when you are selecting the ftf in the flash tool , at the right side check all at the wipe section , and uncheck all at the exclude section
but your internal storage might get also wiped , but i assume it already happened when you unlocked your boot loader
elias234 said:
download any FTF , 4.2.2 or 4.3 , connect your device to flash tool as flashmode , and select to flash the ftf , when you are selecting the ftf in the flash tool , at the right side check all at the wipe section , and uncheck all at the exclude section
but your internal storage might get also wiped , but i assume it already happened when you unlocked your boot loader
Click to expand...
Click to collapse
Alrighty then, I'll give that a go later. I have just found a 4.3 for Australia, perhaps it will be different. Thanks for the quick reply.
keringkien said:
Alrighty then, I'll give that a go later. I have just found a 4.3 for Australia, perhaps it will be different. Thanks for the quick reply.
Click to expand...
Click to collapse
this thread could be helpful : http://forum.xda-developers.com/showthread.php?t=2229250
i'm not sure if that problem could be solve, but it was, like you said, different. never saw anything like that either.
Anyway:
Can it boot into custom recovery in its state now?( for mounting storage for something else in case you have cwm or twrp installed)
Jambu95 said:
this thread could be helpful : http://forum.xda-developers.com/showthread.php?t=2229250
i'm not sure if that problem could be solve, but it was, like you said, different. never saw anything like that either.
Anyway:
Can it boot into custom recovery in its state now?( for mounting storage for something else in case you have cwm or twrp installed)
Click to expand...
Click to collapse
Thanks so much for the reply. The thread has something I can try, if this new rom fails (I expect it will). What is custom recovery? I cannot access the storage, only fastboot and flashmode. no cwm and xdr was never completed.
ROM just failed, trying SUS now.
keringkien said:
Thanks so much for the reply. The thread has something I can try, if this new rom fails (I expect it will). What is custom recovery? I cannot access the storage, only fastboot and flashmode. no cwm and xdr was never completed.
ROM just failed, trying SUS now.
Click to expand...
Click to collapse
oh dear, custom recovery is cwm (clockworkmod recovery) or twrp (team win recovery project), it means, it allows you to do something important just before it boot into system, which is bootstall or bootloop as you call it. you cannot boot into system, then try to boot into recovery ( which is before it boot the system), that might help.
both recoveries will allow you to mount storage to copy things to sd cards from pc.
you can try unlock bootloader and flash custom kernel with recoveries, maybe you "could" boot into one of those recoveries.
I also got the same problem, but mine is a C6602. I was trying to setup a mail exchange, then it asked for some permission. I push enter, then after an hour, it start the bootloop.
The phone boot till the main screen, i could swipe and play around for 10 second, then it reboot.
I have tried everything from hard reset, to FlashTool to SUS, relock, unlock, flash stock, from old stock to new stock, it just won't work :|
Jambu95 said:
oh dear, custom recovery is cwm (clockworkmod recovery) or twrp (team win recovery project), it means, it allows you to do something important just before it boot into system, which is bootstall or bootloop as you call it. you cannot boot into system, then try to boot into recovery ( which is before it boot the system), that might help.
both recoveries will allow you to mount storage to copy things to sd cards from pc.
you can try unlock bootloader and flash custom kernel with recoveries, maybe you "could" boot into one of those recoveries.
Click to expand...
Click to collapse
I'm well aware what cwm is, I just assumed that because you said 'custom' that it might possibly be different, as recovery is always custom anyway, sorry for the misunderstanding.
I am able to flash a 'boot.img' that enables me to use cwm and twrp, HOWEVER, the only way I can access it (as in cause the phone to remain on long enough for it to parse the boot.img) is to connect the phone to my computer in fastboot mode, then using the Fastboot command: "fastboot continue", it will run the 'img' and allow me to enter twrp or cwm. It still won't begin charging or even show the Xperia logo if I allow it to continue without accessing the recovery options.
Thanks for your help.
keringkien said:
I'm well aware what cwm is, I just assumed that because you said 'custom' that it might possibly be different, as recovery is always custom anyway, sorry for the misunderstanding.
I am able to flash a 'boot.img' that enables me to use cwm and twrp, HOWEVER, the only way I can access it (as in cause the phone to remain on long enough for it to parse the boot.img) is to connect the phone to my computer in fastboot mode, then using the Fastboot command: "fastboot continue", it will run the 'img' and allow me to enter twrp or cwm. It still won't begin charging or even show the Xperia logo if I allow it to continue without accessing the recovery options.
Thanks for your help.
Click to expand...
Click to collapse
if you can mount the storage, you could copy the flashable stock rom (4.3) and copy it into your sd card, and maybe you can flash through there by following instructions from that thread.
---------- Post added at 11:21 PM ---------- Previous post was at 11:20 PM ----------
billhainh said:
I also got the same problem, but mine is a C6602. I was trying to setup a mail exchange, then it asked for some permission. I push enter, then after an hour, it start the bootloop.
The phone boot till the main screen, i could swipe and play around for 10 second, then it reboot.
I have tried everything from hard reset, to FlashTool to SUS, relock, unlock, flash stock, from old stock to new stock, it just won't work :|
Click to expand...
Click to collapse
look for the disaster recovery thread i posted above
Jambu95 said:
if you can mount the storage, you could copy the flashable stock rom (4.3) and copy it into your sd card, and maybe you can flash through there by following instructions from that thread.
---------- Post added at 11:21 PM ---------- Previous post was at 11:20 PM ----------
Click to expand...
Click to collapse
I tried to mount the storage, my pc wouldn't detect the phones storage, I managed to push the stock rom zip to the sd card using ADB. I still had cwm recovery and could flash the zip using it. Still, however, the phone shuts down before it gets past the kernel logo. Again, I used the phone in Fastboot mode and forced it to continue using "fastboot continue", I left it go past the kernel logo and it is charging at the moment. I may try to start the phone now, yet expect it to crash again.
EDIT: I tried to launch the phone whilst it was charging, the charging symbol went away and the phone remained on a black screen (lcd is on, but nothing is displayed) for a few seconds before shutting off automatically.
EDIT: Happy New Year!
Thank you.
keringkien said:
I tried to mount the storage, my pc wouldn't detect the phones storage, I managed to push the stock rom zip to the sd card using ADB. I still had cwm recovery and could flash the zip using it. Still, however, the phone shuts down before it gets past the kernel logo. Again, I used the phone in Fastboot mode and forced it to continue using "fastboot continue", I left it go past the kernel logo and it is charging at the moment. I may try to start the phone now, yet expect it to crash again.
EDIT: I tried to launch the phone whilst it was charging, the charging symbol went away and the phone remained on a black screen (lcd is on, but nothing is displayed) for a few seconds before shutting off automatically.
EDIT: Happy New Year!
Thank you.
Click to expand...
Click to collapse
this problem occurs with every kernel you've used (including stock and custom kernels)?
Jambu95 said:
this problem occurs with every kernel you've used (including stock and custom kernels)?
Click to expand...
Click to collapse
Yes that is correct, it's current issue (turning off sponanteously) occurred when I was running stock 4.2.2 (no root, no bootloader unlock).
keringkien said:
Yes that is correct, it's current issue (turning off sponanteously) occurred when I was running stock 4.2.2 (no root, no bootloader unlock).
Click to expand...
Click to collapse
lol, you should unlock the bootloader before you flash a custom boot.img. the primary solution now is to flash any rom to see if it boots up normally , then you can still find a way to revert back to stock.
Jambu95 said:
lol, you should unlock the bootloader before you flash a custom boot.img. the primary solution now is to flash any rom to see if it boots up normally , then you can still find a way to revert back to stock.
Click to expand...
Click to collapse
I never said that I flashed a custom boot.img whilst on a locked bootloader. The reason I tried all the things that I have is because the phone was spontaneously shutting down (on stock, unedited). Perhaps once I made the mistake of flashing a boot.img before unlocking, but I have since unlocked and flashed many roms and kernels. Thanks for your reply.
keringkien said:
I never said that I flashed a custom boot.img whilst on a locked bootloader. The reason I tried all the things that I have is because the phone was spontaneously shutting down (on stock, unedited). Perhaps once I made the mistake of flashing a boot.img before unlocking, but I have since unlocked and flashed many roms and kernels. Thanks for your reply.
Click to expand...
Click to collapse
the device can't get pass the sony logo?
edNHour consum
Jambu95 said:
the device can't get pass the sony logo?
Click to expand...
Click to collapse
That is correct, it doesn't hang but suddenly turns off, the only way I can use recovery tools in the kernel is if I plug the phone into my pc in Fastboot mode, then issue the command "fastboot continue" from cmd.
keringkien said:
That is correct, it doesn't hang but suddenly turns off, the only way I can use recovery tools in the kernel is if I plug the phone into my pc in Fastboot mode, then issue the command "fastboot continue" from cmd.
Click to expand...
Click to collapse
i think there is something wrong with your motherboard or the battery connection, i'm not sure, because my pc got that problem before, it just boot up to starting windows... and then reboot, in the end i found out the capacitor got swelled in the power supply.
Jambu95 said:
i think there is something wrong with your motherboard or the battery connection, i'm not sure, because my pc got that problem before, it just boot up to starting windows... and then reboot, in the end i found out the capacitor got swelled in the power supply.
Click to expand...
Click to collapse
That is certainly possible, I have had to replace the back glass and during that operation it is possible that the battery got too hot and is now lower in voltage or something. Thanks for the suggestion, I would appreciate a second opinion with this...
Thank you.
keringkien said:
That is certainly possible, I have had to replace the back glass and during that operation it is possible that the battery got too hot and is now lower in voltage or something. Thanks for the suggestion, I would appreciate a second opinion with this...
Thank you.
Click to expand...
Click to collapse
if you still have your warranty, you can go to the center and request for a replacement, the best solution now is to revert to as stock as possible, if can get the bootloader locked again then it's good,
Jambu95 said:
if you still have your warranty, you can go to the center and request for a replacement, the best solution now is to revert to as stock as possible, if can get the bootloader locked again then it's good,
Click to expand...
Click to collapse
I imagine it is still under warranty, however I have read that unlocking the bootloader permanently voids warranty. And I have replaced the back of my white phone with a black glass, perhaps if I get a new white rear glass it will be ok, but then I might as well just replace the battery $40AUD isn't too expensive IMO.
Related
Hello all! So, I tried to install CM11, the one on this post.
Went into CWM, did Wipe data factory reset and formatted /system. when I tried installing the rom, it said operation aborted and it could not install it. No biggie, the post says to install cm10.2 before doing so.
So i Powered the phone off to copy the file over to the SD. To my surprise, now I can't get into CWM, Philz, TWRP, fastboot or flashmode. Whenever I press the back pin to power the phone off, it turns back on automatically before I have time to press the key and connect the USB cable. Furthermore, when I manage to do it quick enouhg, the green led lights up, but it fades away after 10ish seconds only to display the sony logo again, and a "can't recognize USB device" popup comes up in my PC. I've used flashtool with this same pc in the past, so I don't know what that is about. Also, whenever I try installng flashtool drivers again, just in case 2 things happen:
there is no xperia SP device listed and whatever i select it fails to install.
What can I do now? I had 4.3 with the eXistenZ Ultra ROM before all of this.
Damm, this is the first time this happens to me, I've been swapping roms for ever, and this is not even the first phone i do this in, had a galaxy s2 and a wildfire S before. I feel like such a noob
UPDATE!:
So I finally managed to fix it. I posted this after about 8-9 hours of trying to get into fastboot on the 3 different pcs in my household, all had the drivers at some point and i've worked with them and fastboot and this same phone previously, so I figured they'd still work. They didn't, I couldnot even get SUS to work. So i went to a 4th PC, installed SUS and the needed drivers and it only took like 40 minutes worth of tries. I'm in the software download part of the SUS, i'll keep this updated!
UPDATE2!:
So, it finished downloading but it suddenly disconnected, tried again for about 10 minutes and then got it going again. Downloaded the second time and installed it successfully. Leaving this up for future reference!
Bottomline: if you can't get into flashmode, try on as many PCs as you have available for at least 30 minutes each.
Don't use flash tools just install CM11 with CWM or something, use doomlord kernel to get CWM and install CM11 zip that's it.
Sorry locked boot loader didn't read it correctly don't use my advice .
Th3Duck said:
Don't use flash tools just install CM11 with CWM or something, use doomlord kernel to get CWM and install CM11 zip that's it.
Sorry locked boot loader didn't read it correctly don't use my advice .
Click to expand...
Click to collapse
No problem, it kinda sorted itself out by brute force connections :> Dammed sony, locking the bootloaders for real. I even got the sim unlock code from my phone company and it's still not bootloader unlockable at the phone settings, even though i can now get any sim i want in it -.-
My motorola Nexus 6 won't turn on, when I try to power it on, it shows the Google sign then shuts off immediately. When I plug in the charger from a complete power off, the white battery sign keeps flashing, it shows for 1 second then shuts off then repeats the cycle of showing the battery sign then shutting off. It boots into bootloader/fastboot mode fine, and I have tried flashing the factory image, it flashes fine but it still shuts off immediately while showing the google sign. It won't even boot into recovery after the flash, it just shuts off after the google sign. This isn't my first nexus, in know that flashing factory image should fix 99% of issues. Please help.
P.S I didn't purchase officially from google or Motorola, bought it from a guy who claimed he bricked it trying to install a font pack so I figured let me buy it and restore factory image. Didn't work. I tried flashing manually, the process went fine, but it it still turns off at google splash image. I tried Wugfresh toolkit also to no avail. He said he rooted it, installed custom recovery and euphoria os rom. Then he installed the fontpack, it told him to reboot to apply changes, and it wouldn't boot past google screen after that. It doesnt even get to the boot animation. It just shuts off. When its off and u plug in the charger it does the same thing, you just keep seeing the charging symbol over and over because its constantly rebooting. Its a T-Mobile Nexus 6 BTW, model number XT1103. I spoke to my friend who has a local repair shop and he says there is nothing out for his z3x or his other boxes for the nexus 6 because it is such a new and rare device. His theory is that the partition tables have been corrupted somehow and need to be rewritten manually. Please any help would be appreciated. I can promise a hefty $$ reward for any individual that helps me recover it to a working state.
can you get a custom recovery on successfully.........?
did you flash the stock image manually?
mediaman123 said:
can you get a custom recovery on successfully.........?
did you flash the stock image manually?
Click to expand...
Click to collapse
Yes I tried pushing the stock recovery individually and it succeeded in the command prompt, but won't enter recovery, just shows google and shuts off. I tried pushing twrp too but same outcome. Yes I had flashed the stock image manually, everything flashed well from what the command promt said, but when it should reboot to recovery after flash to wipe, just shuts off.
jeromechrome1 said:
Yes I tried pushing the stock recovery individually and it succeeded in the command prompt, but won't enter recovery, just shows google and shuts off. I tried pushing twrp too but same outcome. Yes I had flashed the stock image manually, everything flashed well from what the command promt said, but when it should reboot to recovery after flash to wipe, just shuts off.
Click to expand...
Click to collapse
Please! Anyone!
by manually do you mean flashing all the separate parts of the stock image separately, system, boot, recovery, cache and so on..........
I don't know what else to do after going through with that process.....
Make sure you have the latest fastboot by updating SDK Manager. Then reflash bootloader then reboot back to bootloader to reset. Then proceed to flash each partition again. Directions below.
fastboot flash bootloader bootloader.img <-- rename bootloader to this to make it easier
fastboot flash radio radio.img <--- again rename to make easier
fastboot flash boot boot.img
fastboot flash cache cache.img
fastboot flash recovery recovery.img
fasyboot flash system system.img
Hope this helps.
I'm a total newb here so take what I tell you with a grain of salt. I had your exact same problem on my Nexus 5. Every single thing you just described is what happened to my N5. And just like your N6...I was able to boot up into recovery (stock and TWRP), I was able to flash all the things manually and even used Wug's NRT. But then whenever I tried to actually boot up the device it could never pass the Google logo....basically EVERYTHING THAT IS HAPPENING TO YOU.
What I did to fix everything? Changed my battery. Sounds stupid and totally irrelevant but that did the trick. When I opened up my phone I noticed my battery had a nasty bulge and realized it was defective. Bought a new one for $25 and have never had any issues ever since. I suggest you look at your battery and see if that is the root of your problem. I have heard of the N6 having some batteries expanding and causing the back covers to pop off...this could be related to your problem.
Like I said I am a newb and thought I'd share my experience in the hopes it solves your problem.
Good luck buddy! :good:
my N6 is actually away getting repaired for the exact issue you described, expanding battery [assumed], and cover coming away from the bezel.....
I believe though that if you keep the device plugged into the wall when trying to boot up with this battery defect it will get through the boot, at least in the beginning anyway....
I believe also that if it was a battery issue the device would power off first, as opposed to just sticking on the Google logo.........
ldkud50 said:
Make sure you have the latest fastboot by updating SDK Manager. Then reflash bootloader then reboot back to bootloader to reset. Then proceed to flash each partition again. Directions below.
fastboot flash bootloader bootloader.img <-- rename bootloader to this to make it easier
fastboot flash radio radio.img <--- again rename to make easier
fastboot flash boot boot.img
fastboot flash cache cache.img
fastboot flash recovery recovery.img
fasyboot flash system system.img
Hope this helps.
Click to expand...
Click to collapse
I tried all of that already bro, it takes the files fine i did each individually including the bootloader. yes i have the latest sdk and latest fasboot. same issue no matter what i try. thank you all for ur help so far, really appreciate it.
jeromechrome1 said:
I tried all of that already bro, it takes the files fine i did each individually including the bootloader. yes i have the latest sdk and latest fasboot. same issue no matter what i try. thank you all for ur help so far, really appreciate it.
Click to expand...
Click to collapse
Thats too bad. Maybe the device is hosed. RMA for a new one.
Same thing happened to me. As soon as I updated to the newest version of fastboot on my computer, everything worked...
jeromechrome1 said:
My motorola Nexus 6 won't turn on, when I try to power it on, it shows the Google sign then shuts off immediately. When I plug in the charger from a complete power off, the white battery sign keeps flashing, it shows for 1 second then shuts off then repeats the cycle of showing the battery sign then shutting off. It boots into bootloader/fastboot mode fine, and I have tried flashing the factory image, it flashes fine but it still shuts off immediately while showing the google sign. It won't even boot into recovery after the flash, it just shuts off after the google sign. This isn't my first nexus, in know that flashing factory image should fix 99% of issues. Please help.
P.S I didn't purchase officially from google or Motorola, bought it from a guy who claimed he bricked it trying to install a font pack so I figured let me buy it and restore factory image. Didn't work. I tried flashing manually, the process went fine, but it it still turns off at google splash image. I tried Wugfresh toolkit also to no avail. He said he rooted it, installed custom recovery and euphoria os rom. Then he installed the fontpack, it told him to reboot to apply changes, and it wouldn't boot past google screen after that. It doesnt even get to the boot animation. It just shuts off. When its off and u plug in the charger it does the same thing, you just keep seeing the charging symbol over and over because its constantly rebooting. Its a T-Mobile Nexus 6 BTW, model number XT1103. I spoke to my friend who has a local repair shop and he says there is nothing out for his z3x or his other boxes for the nexus 6 because it is such a new and rare device. His theory is that the partition tables have been corrupted somehow and need to be rewritten manually. Please any help would be appreciated. I can promise a hefty $$ reward for any individual that helps me recover it to a working state.
Click to expand...
Click to collapse
I know, it's been a long time, but coud you tell me what happened to the phone?
Hi.
I've been searching for a solution on how to fix my phone for already almost a year now. I didn't even do anything to it, no custom recoveries or OS (wanted to get CM, but at the time it wasn't available on it, not sure if now is).
The problem - the phone is stuck in a bootloop with an empty battery. The battery wasn't empty at the beginning, but it died in the process of trying to make it work, since the only thing I can boot is "fastboot&rescue" mode, in which the phone doesn't charge - how sweet. Now, I've read just about every thread here on how to flash custom (and original) recoveries, all the DLOAD folder versions and everything, and somewhere in between all that I found that it's impossible to flash anything if the battery is low (or totally empty).
The question - how do I charge the battery if it doesn't boot in anything other than fastboot, and when I plug it in the wall it just loops and loops and loops, and doesn't even charge? It's also impossible to turn it off while it's plugged in the charger. WTF, Huawei, really?
Any help appreciated. Cheers,
Can you Boot into recovery through pressing power + volume+?
You may have to remove the back of your phone and buy a new battery. The disassambling process is pretty simple, but of course you will loose any guarantee..
l3Nni said:
Can you Boot into recovery through pressing power + volume+?
You may have to remove the back of your phone and buy a new battery. The disassambling process is pretty simple, but of course you will loose any guarantee..
Click to expand...
Click to collapse
No, can't boot into recovery, only fastboot. If I could, I guess I would've already fixed it, heh.
I actually got it to charge, at least that's what I think. There was a *.bat script somewhere here that was repeatedly doing these two things:
1) fastboot getvar battery-voltage
2) fastboot reboot-bootloader
So, I ran that (while the phone was plugged in my computer and running fastboot mode), and it began looping and looping and looping. Left it like that for the night. Now, in the morning, when I unplugged it and tried to do someting, the red "battery low" LED wasn't glowing/blinking anymore! Since "fastboot getvar battery-voltage" returned an error all the time (remote: command not allowed), I don't exactly know how much power I have in it, but I'll just leave it like that for a day or two now, and then try some of the methods I've already tried before. Got any new ones I could try?
I already removed the back and removed the battery - wanted to see if I can charge it externally, but has a very small connector to connect it to the mother board, and I can't just put it in any external charger - I actually didn't find any external chargers that can charge the battery of this phone, really strange.
About the warranty - don't even care anymore. Somehow I managed to get a small crack on the glass on the back of the phone just a few days after getting it. Screen is not damaged, just the back cover. And, you don't know Latvia, but this is how it goes here. I took it to a repair shop - the one I needed to take my device for warranty repair. However, in Latvia that means it's just an another small repair shop, which just happens to have a contract with the company who sold me the phone (mobile phone operator). So, they take my phone, say they'll do a diagnostic and get back to me. Three weeks pass, and they call me telling that the only thing they can do is replace the motherboard, which is gonna cost me about 250 euros. That, or nothing. I don't agree. That means, if I don't agree to their suggested method of repairing, I have to pay for the diagnostic (about 20 euros).
Well, good idea, looks like you will get your phone running..
To unbrick your device you need to flash a recovery that matches with the firmware you had been on. So, if you had a B1xx Rom running try flashing TWRP 2.8.1.0 and MyRom 1.2. After that flash the stock emui 2.3 recovery and B133 through dload. If you were on a B6xx Ron flash TWRP 2.8.7.0 and MyRom 3.3, then emui 3.0 Recovery and B621.
When you didn't try this way until now, do it. It should work if the device isn't hardbricked.. I wish you the best.
l3Nni said:
Well, good idea, looks like you will get your phone running..
To unbrick your device you need to flash a recovery that matches with the firmware you had been on. So, if you had a B1xx Rom running try flashing TWRP 2.8.1.0 and MyRom 1.2. After that flash the stock emui 2.3 recovery and B133 through dload. If you were on a B6xx Ron flash TWRP 2.8.7.0 and MyRom 3.3, then emui 3.0 Recovery and B621.
When you didn't try this way until now, do it. It should work if the device isn't hardbricked.. I wish you the best.
Click to expand...
Click to collapse
Just flashed TWRP 2.8.1.0, it's already getting better. Now when I tried turning it on in recovery mode, it's not just simply bootlooping all the time, but is stuck on the Huawei logo. At least I hope that's better If I try to turn it on normally it just bootloops again. Omg omg omg.
l3Nni said:
Well, good idea, looks like you will get your phone running..
To unbrick your device you need to flash a recovery that matches with the firmware you had been on. So, if you had a B1xx Rom running try flashing TWRP 2.8.1.0 and MyRom 1.2. After that flash the stock emui 2.3 recovery and B133 through dload. If you were on a B6xx Ron flash TWRP 2.8.7.0 and MyRom 3.3, then emui 3.0 Recovery and B621.
When you didn't try this way until now, do it. It should work if the device isn't hardbricked.. I wish you the best.
Click to expand...
Click to collapse
Well, tried everything again. Flashing all those recoveries, nothing, can't get a recovery. Put a dload folder with update.app in it, magic 3 button combo just gives me some more of that good old bootloop. Extracted everything from the update.app, flashed recovery, system and boot with fastboot - all showed success. I got the most excited when it got to flashing system - it was quite big and took quite long, and returned success, so I really hoped that really did something - but no. Downloaded P7 kernel. Tried "fastboot flash:raw boot P7_kernel" ("P7_kernel" is the name of the file). It created a boot image (544985088 bytes), sending 'boot' returned "OKAY [20.622s]", then "writing boot" returned "FAILED (remote: flash write failure)". Is this the thing that's really broken? The boot flash partition? If so - what can I do, if anything?
God I hate this phone. The best is that I only used it for 3 months, and I still have to pay for it for more than a year. It's been in this condition for 7-8 months already. FML.
edzjins said:
Well, tried everything again. Flashing all those recoveries, nothing, can't get a recovery. Put a dload folder with update.app in it, magic 3 button combo just gives me some more of that good old bootloop. Extracted everything from the update.app, flashed recovery, system and boot with fastboot - all showed success. I got the most excited when it got to flashing system - it was quite big and took quite long, and returned success, so I really hoped that really did something - but no. Downloaded P7 kernel. Tried "fastboot flash:raw boot P7_kernel" ("P7_kernel" is the name of the file). It created a boot image (544985088 bytes), sending 'boot' returned "OKAY [20.622s]", then "writing boot" returned "FAILED (remote: flash write failure)". Is this the thing that's really broken? The boot flash partition? If so - what can I do, if anything?
God I hate this phone. The best is that I only used it for 3 months, and I still have to pay for it for more than a year. It's been in this condition for 7-8 months already. FML.
Click to expand...
Click to collapse
Hi, is your bootloader unlocked??? I think you cant write the boot partition if tour p7 is not unlocked, hace you tried flashing stock recovery? Try the b135
SiulGKT said:
Hi, is your bootloader unlocked??? I think you cant write the boot partition if tour p7 is not unlocked, hace you tried flashing stock recovery? Try the b135
Click to expand...
Click to collapse
Hi. Yes, bootloader unlocked, 100% sure. Have tried flashing the stock recovery, no changes. Tried to find the b135 now - I actually failed to find a real, valid download link! All I found were some russian ****up sites, which downloaded some russian ****ing malware! WTF? I'm about to give up on this phone. Just destroy it with all my hate for it. **** this ****ing piece of **** to hell. There is no hope, and **** my life. Whatever.
Be patient. I'll give you link soon but give me answers for this questions.
What was yours last valid ROM ?
Dude you can't flash any recovery you want.... It's not simply working between different ROMs.
Second question. Do you unplaged usb cable before flashing ROM by force update (3 buttons) ?
PS
I am not sure but battery isn't charging even fastboot mode or if totally device is off ?
Sent from my HUAWEI P7-L10 using Tapatalk
Ziolek67 said:
Be patient. I'll give you link soon but give me answers for this questions.
What was yours last valid ROM ?
Dude you can't flash any recovery you want.... It's not simply working between different ROMs.
Second question. Do you unplaged usb cable before flashing ROM by force update (3 buttons) ?
PS
I am not sure but battery isn't charging even fastboot mode or if totally device is off ?
Sent from my HUAWEI P7-L10 using Tapatalk
Click to expand...
Click to collapse
My last valid ROM is the only one I ever had - EMUI, whichever was the latest about a year ago.
After flashing recovery in fastboot mode, I unplugged the cable and pressed the power button and helt it until it turned off. Waited for a minute to see if it doesn't turn on, to make sure it's completely off - just what the instructions say. Then I tried the force update with 3 buttons, cable unplugged. With stock ROM it was still bootlooping, no changes at all, but with TWRP 2.8.1.0 it got stuck at Huawei logo - but no bootloop. Just Huawei logo, nothing else.
Battery is not charging in fastboot mode because that's how it is on all phones. But it's also not charging when it's totally off, because when I plug it in the charger, it automatically tries to turn on, and starts bootlooping. It's impossible to charge it then. However, with the .bat script I guess I have solved the charging problem - at least the red LED doesn't light/flash anymore.
Emui 3.0 beta release was at the end of 2014, official B609 in January 2015. It's important what rom you have been on. Trying different ones is just a waste of time..
You may try to extract and flash Bxxx part for part (depends on what rom you were) and then TWRP 2.8.1.0/2.8.7.0.I have no other idea, unfortunately.
It's a stupid question, but did you, when trying to boot into recovery, press volume+ for a longer time?
edzjins said:
My last valid ROM is the only one I ever had - EMUI, whichever was the latest about a year ago.
After flashing recovery in fastboot mode, I unplugged the cable and pressed the power button and helt it until it turned off. Waited for a minute to see if it doesn't turn on, to make sure it's completely off - just what the instructions say. Then I tried the force update with 3 buttons, cable unplugged. With stock ROM it was still bootlooping, no changes at all, but with TWRP 2.8.1.0 it got stuck at Huawei logo - but no bootloop. Just Huawei logo, nothing else.
Battery is not charging in fastboot mode because that's how it is on all phones. But it's also not charging when it's totally off, because when I plug it in the charger, it automatically tries to turn on, and starts bootlooping. It's impossible to charge it then. However, with the .bat script I guess I have solved the charging problem - at least the red LED doesn't light/flash anymore.
Click to expand...
Click to collapse
Than you probably have EMUI 2.3 ROM version.
Try flashing B135 recovery from here.
Next try to install B135 ROM from this link.
l3Nni said:
Emui 3.0 beta release was at the end of 2014, official B609 in January 2015. It's important what rom you have been on. Trying different ones is just a waste of time..
You may try to extract and flash Bxxx part for part (depends on what rom you were) and then TWRP 2.8.1.0/2.8.7.0.I have no other idea, unfortunately.
It's a stupid question, but did you, when trying to boot into recovery, press volume+ for a longer time?
Click to expand...
Click to collapse
No, it broke down before EMUI 3 came out, then. I guess I had the ROM which was just before EMUI 3.
Usually when trying to boot into recovery I press the volume+, hold it for about 10 seconds, and then press and hold the power button until it starts turning on. Then I hold both of them for some time, then release the power button but keep the volume button pressed. I've tried doing it differently - holding both buttons for longer time, releasing both as soon as it starts turning on, nothing I've tried works.
edzjins said:
No, it broke down before EMUI 3 came out, then. I guess I had the ROM which was just before EMUI 3.
Usually when trying to boot into recovery I press the volume+, hold it for about 10 seconds, and then press and hold the power button until it starts turning on. Then I hold both of them for some time, then release the power button but keep the volume button pressed. I've tried doing it differently - holding both buttons for longer time, releasing both as soon as it starts turning on, nothing I've tried works.
Click to expand...
Click to collapse
B135 recovery
http://forum.xda-developers.com/ascend-p7/general/trying-to-update-rom-1-2-t3222485
I uploaded it couple days ago...
OK, I left it "charging" for 2 days straight, hoping maybe battery was too low to flash partitions or whatever. Just wanted to make sure the battery is charged enough. I can't check the voltage or the percentage, because "fastboot getvar battery-voltage" always says that it's forbidden, no permissions, whatever.
So, I left it to charge for 2 days, and now I tested all the things you guys have posted here. Carefully, one by one. Every fastboot flash command returned success, but in the end nothing changed. Doesn't matter which recovery and/or boot I flash, it's just stupidly bootlooping all the time. Nada.
Finally, you can buy a defect P7 (with a broken screen or anything like this) for pretty low money on eBay and change the motherboard.
But I could also understand it well if you just throw it out of the window.. You had really bad luck.
Probably i have the same problem..... You solve yours problem with this ?
Nop, didn't solve the bootloop. I managed to get a donor phone for 55eur though, which had a bent body and wasn't functioning well because of that, and the screen was a bit cracked too. So I did a motherboard swap. Worked perfectly, but the battery connector protecting case screw doesn't hold in anymore, so sometimes it just turns off because it loses connection, or something. I tried to fasten it with some duct tape, hoped it'd help, and put a hard case on it - got better, but still fails sometimes.
I try give it back on warranty, i hope thei repair it.
I am in the EXACT same boat as edzjins. I have wasted 4 days of my precocious life trying to flash stuff on a phone with a completely dead battery.
I just doesn't work, period!
The only possible fix is to buy a new battery, replace the old one, and after the new battery is installed, have all of the flashing software ready to go and fired up before the new battery dies, too!
Its a time game.
Just like edzjins, there was a brief period of time when I thought I could stop the bootloop via TWRP recovery, but was unable to and the battery completely died.
Be wary of trying to flash "EdXposed" framework with TWRP. Instead, flash it only through Magisk.
I have learned the hard way : (
Having gotten a spare Xperia SP, I decided to venture into the realm of flashing custom ROMs. This was the first time I did anything of this sort with an Android device. So, here is what I did to it today:
At first, I successfully rooted, installed recovery and flashed CM12. After fiddling with it for about an hour and not finding anything super exciting, I decided to try out other ROMs. I did a facotry reset, wiped the data and cache, and was about to flash CM11 (I forgot that it required an unlocked bootloader, which I don't have, and the recovery console told me so). Maybe at this point I should have just reflashed CM12, but I chose (not even sure why at this point) to exit recovery instead. After this, the phone keeps getting stuck on the Sony logo (although on the second attempt to turn it on, it did display a screen showing that wrench icon, indicating some sort of configuration activity going on, but never moved past that either). I tried flashing two different stock ftf roms with flashtool, both fail with this error: Processing of system.sin finished with errors. One of them will cause the phone to shut off after about a minute on the logo instead of remaining stuck on it indefinitely.
Maybe I should mention that this phone did not exactly work flawlessly for some time, even before I started experimenting with it. Here are the main things that I can remember it doing:
-Lags on even the basic functions, apps often crashing, despite doing a very recent hard reset.
-Battery drains very fast sometimes (like going from 55% to 0 in about 2 hours with almost no usage).
-A few months ago, it would periodically freeze and reboot itself, but that problem seemed to disappear with time.
Did I do something stupid to that phone, or are there internal/hardware problems that have manifested themselves in this way? I won't be horribly upset if I killed it (after all, knowing that something of this sort may happen was exactly the reason why I was not doing all this on my main phone), but I certainly would like to get it back up and running.
Download Flashtool v0.9.18.6 from official site.
Option 1: Flash stock.
or,
Option 2: Flash tangerine-7.1.elf via 'fastboot mode' to directly get TWRP, then flash any ROM you want.
https://dl.cubeserver.eu/TechnoSparks/tangerine-stuffs/tangerine-7.1.elf
nandan21 said:
Download Flashtool v0.9.18.6 from official site.
Option 1: Flash stock.
or,
Option 2: Flash tangerine-7.1.elf via 'fastboot mode' to directly get TWRP, then flash any ROM you want.
]
Click to expand...
Click to collapse
Thank you for your reply. I have a few questions:
I downloaded the flashtool version that you mentioned (from the official site), but avast detected malware in it. Should version 9.19.8, the one I tried yesterday, work fine?
What is exactly considered "stock rom"? Is it exclusively the version your phone came with, or is it firmware of any version/carrier branding, as longs as it is made for your phone model by the manufacuter?
It looks like my phone actually won't stay in flash mode. I select fastboot mode in flashtool, a window pops up asking me to plug in the phone. I press the volume down button and plug it in, the LED glows bright green, but nothing happens in flashtool. After a few seconds, the LED goes red and the Sony logo appears on the phones screen (as if it was going to turn on), and my computer makes a sound as if the phone was ejected. The phone shuts off a minute later, goes into flash mode again, and the cycle repeats.
UPDATE
Nevermind everything I wrote before, I was able to successfully re-flash stock. Turns out I did in fact have some crappy version of flashtool that didn't work, and I found anolder version without malware.
Strangely, the infected flashtool version was the one I dowloaded from the official site... Something is fishy here.
Anyways, thanks a bunch for your help!
MrDroid15 said:
Thank you for your reply. I have a few questions:
I downloaded the flashtool version that you mentioned (from the official site), but avast detected malware in it. Should version 9.19.8, the one I tried yesterday, work fine?
What is exactly considered "stock rom"? Is it exclusively the version your phone came with, or is it firmware of any version/carrier branding, as longs as it is made for your phone model by the manufacuter?
It looks like my phone actually won't stay in flash mode. I select fastboot mode in flashtool, a window pops up asking me to plug in the phone. I press the volume down button and plug it in, the LED glows bright green, but nothing happens in flashtool. After a few seconds, the LED goes red and the Sony logo appears on the phones screen (as if it was going to turn on), and my computer makes a sound as if the phone was ejected. The phone shuts off a minute later, goes into flash mode again, and the cycle repeats.
Click to expand...
Click to collapse
Use flashtool 0.9.19.8 because that is what everyone is recommending now, Stock rom defines as what it originally comes from your phone which is manufactured by sony. To get into fastboot mode turn off your phone by taking off the cover off your xperia sp and use a pin or pen to press into a small dot and you will get 3 vibrations.
This guide is not written by me, so give credit to chris10286
Step 1. Download a kernel with twrp embedded im sure I used dooms kernel as far as I remember. There are many others just do a simple google of xperia sp kernel with recovery.
Step 2 . take phone case off the back hold button in on lower bottom for 10 seconds you will get 3 vibrations . good leave it at that.
Step 4 . open flashtool let it load completely. Now plug USB into your phone also have it into your PC ! Whilst plugging in hold down volume button to enter flashmode your phone should be green . hold up for fast boot mode which is blue either too let's you flash a kernel but fast boot mode requires "elf" kernel.
Step 5. Locate kernel install and then boot phone up whilst press the volume up button as its booting recovery mode will be accessed now flash rom of your choice or use Sony PC suite to go back to stock. Make sure you have stock kernel and bootloader locked or else it won't let you..
Use this thread to help you since i had the similar problem which involved my phone: http://forum.xda-developers.com/showthread.php?p=63660062#post63660062
If none of my methods work please ask zenith to help you or ask anyone in the xperia sp forum to help you since im not a developer but ran into a similar problem to yours.
I hope this helps you out in someway as it did me good luck.
Thanks Nandan
Thank you, I very much appreciate that you took the time to write this long post to help me out. As I mentioned in an earlier post, I found a solution to my problem - by using flashtool 9.18.6 (the one that wasn't working was actually newer).
Hello my fellow friends in HTC Desire 626s Metro PCs land.
This is Isaiah speaking. I've run into a little misfortune here and I wanted to know if someone would be kind enough to help me out.
I have seemed to get myself in a little snag, were for some reason after I relock my phone, it won't reboot the system. What happens is, it boots right into download mode. So I unlocked it again and guess what. Everything booted normally.
Then I go to unlock it again, it jumps right back to download mode. I'm going bonkers over here, like Willy Wonka bonkers because i can't figure out why I can't relock my phone without it going right back to download mode. I flashed stock recovery through cmd, before I relocked it, that didn't work. All I did was root my phone. No debloated roms or anything. Just simply rooted my phone. I'm on Android 6.0.1. Somebody will you please help me get back to stock. Sigh, momma told there'd be days like this! Lol!!! I had to throw in a little humor.
I had the exact same problem. I found a possible fix. If you are just trying to get back to the recovery area.
Press and hold the power and volume down keys then release the power.
Once on the download mode screen scroll to Reboot to bootloader
Once in the bootloader area select Reboot to recovery mode.
This is the only way I can get to recovery mode.
Ace18o said:
I had the exact same problem. I found a possible fix. If you are just trying to get back to the recovery area.
Press and hold the power and volume down keys then release the power.
Once on the download mode screen scroll to Reboot to bootloader
Once in the bootloader area select Reboot to recovery mode.
This is the only way I can get to recovery mode.
Click to expand...
Click to collapse
What i'm trying to do is actually get back to the stock recovery so that I can re-flash the official ruu file from the official HTC Roms Website because my phone has not been running smoothly on the ota update they sent out in July. I figured since the the sites ruu file is 1.32gb and the actual ota update was 845mb, may-be there's something in the ruu that will fix this issue.
I already tried unrooting it by flashing stock recovery through command prompt then going back and re-locking my device. But after I re-locked my phone, instead of it rebooting normally where it goes to the boot animation, then loads the welcome screen to allow you to go through putting your wifi info and email address etc. It returns to download mode, or boot loader mode. Then every time I restart my phone it does the same thing and it goes back to the same screen. But when I re-unlock it, it boots fine.
s3llz said:
What i'm trying to do is actually get back to the stock recovery so that I can re-flash the official ruu file from the official HTC Roms Website because my phone has not been running smoothly on the ota update they sent out in July. I figured since the the sites ruu file is 1.32gb and the actual ota update was 845mb, may-be there's something in the ruu that will fix this issue.
I already tried unrooting it by flashing stock recovery through command prompt then going back and re-locking my device. But after I re-locked my phone, instead of it rebooting normally where it goes to the boot animation, then loads the welcome screen to allow you to go through putting your wifi info and email address etc. It returns to download mode, or boot loader mode. Then every time I restart my phone it does the same thing and it goes back to the same screen. But when I re-unlock it, it boots fine.
Click to expand...
Click to collapse
Ahh my bad, I was very tired last night.
s3llz said:
What i'm trying to do is actually get back to the stock recovery so that I can re-flash the official ruu file from the official HTC Roms Website because my phone has not been running smoothly on the ota update they sent out in July. I figured since the the sites ruu file is 1.32gb and the actual ota update was 845mb, may-be there's something in the ruu that will fix this issue.
I already tried unrooting it by flashing stock recovery through command prompt then going back and re-locking my device. But after I re-locked my phone, instead of it rebooting normally where it goes to the boot animation, then loads the welcome screen to allow you to go through putting your wifi info and email address etc. It returns to download mode, or boot loader mode. Then every time I restart my phone it does the same thing and it goes back to the same screen. But when I re-unlock it, it boots fine.
Click to expand...
Click to collapse
Just don't lock the boot loader, I didn't lock my boot loader to run the RUU. My phone was running the firmware that if came with and I had unlocked the boot loader, flashed TWRP, and rooted. All I did was flash the stock recovery then ran the RUU(it didn't work turned off so I booted into fastboot) and it updated.
Problem solved
IsaacGuti said:
Just don't lock the boot loader, I didn't lock my boot loader to run the RUU. My phone was running the firmware that if came with and I had unlocked the boot loader, flashed TWRP, and rooted. All I did was flash the stock recovery then ran the RUU(it didn't work turned off so I booted into fastboot) and it updated.
Click to expand...
Click to collapse
Thank you so much for your advice. It worked like a charm. Consider this case closed. I downloaded the official ruu file for my particular carrier and left the boot loader unlocked, but installed the stock recovery through command prompt. Then, I connected my device to my pc via usb as instructed through the ruu. Then, zing.....watched it zap my phone with the stock rom of 6.0.1. Solved my lagging issues as well as my network switching issues as well. For some strange reason, my device kept switching between different carriers which caused me not to be able to sent text messages. I was like "What in the Doc Brown Marty McFly is going on here!!!" Had me like Doc Brown "Great Scott!!!!" LOL!! Thanks buddy for your advice though. Problem Solved.:good::highfive::victory::victory:
s3llz said:
Thank you so much for your advice. It worked like a charm. Consider this case closed. I downloaded the official ruu file for my particular carrier and left the boot loader unlocked, but installed the stock recovery through command prompt. Then, I connected my device to my pc via usb as instructed through the ruu. Then, zing.....watched it zap my phone with the stock rom of 6.0.1. Solved my lagging issues as well as my network switching issues as well. For some strange reason, my device kept switching between different carriers which caused me not to be able to sent text messages. I was like "What in the Doc Brown Marty McFly is going on here!!!" Had me like Doc Brown "Great Scott!!!!" LOL!! Thanks buddy for your advice though. Problem Solved.:good::highfive::victory::victory:
Click to expand...
Click to collapse
By any chance, do you have the stock recovery link? I'm having the same issue :/
Sharkyzz said:
By any chance, do you have the stock recovery link? I'm having the same issue :/
Click to expand...
Click to collapse
I will upload it so that you can dowload it. Make sure when you go in to command prompt that you type exactly what it says "Stock_Recovery.img" without the parenthesis of course. Thats what i had to do. it will look like this when you type it in "fastboot flash recovery Stock_Recovery.img"
Link below.
https://drive.google.com/file/d/0ByVHpaOig07QT1hfUmY4bkZrbGs/view?usp=sharing
s3llz said:
I will upload it so that you can dowload it. Make sure when you go in to command prompt that you type exactly what it says "Stock_Recovery.img" without the parenthesis of course. Thats what i had to do. it will look like this when you type it in "fastboot flash recovery Stock_Recovery.img"
Link below.
https://drive.google.com/file/d/0ByVHpaOig07QT1hfUmY4bkZrbGs/view?usp=sharing
Click to expand...
Click to collapse
PS. Also, when I used the Rom update utility it failed once. But if you look carefully at the picture instructions on the screen, it tells you to unplug your usb cable and pull out the battery. But of course we both know we can't take out the battery. So what you do is, just unplug the usb, but don't restart your phone. Leave it on the screen where it stopped on. When you get to the screen where it tells you to plug your usb back in, then you plug it back in. After that, you just follow the instructions on the screen of the ruu, and it will begin flashing your device with the stock rom. That was the step I kept missing. To unplug the usb and then plug it back in when the ruu says to.
s3llz said:
I will upload it so that you can dowload it. Make sure when you go in to command prompt that you type exactly what it says "Stock_Recovery.img" without the parenthesis of course. Thats what i had to do. it will look like this when you type it in "fastboot flash recovery Stock_Recovery.img"
Link below.
https://drive.google.com/file/d/0ByVHpaOig07QT1hfUmY4bkZrbGs/view?usp=sharing
Click to expand...
Click to collapse
PS. Also, when I used the Rom update utility it failed once. But if you look carefully at the picture instructions on the screen, it tells you to unplug your usb cable and pull out the battery. But of course we both know we can't take out the battery. So what you do is, just unplug the usb, but don't restart your phone. Leave it on the screen where it stopped on. When you get to the screen where it tells you to plug your usb back in, then you plug it back in. After that, you just follow the instructions on the screen of the ruu, and it will begin flashing your device with the stock rom. That was the step I kept missing. To unplug the usb and then plug it back in when the ruu says to.