Related
Hey Guys, I am in trouble and any help/advise will be highly appreciated....
So, First thing first.
Problems:
1. USB Port is Buggy, Cant connect to 0din or PC. I can just charge it.
2. Recovery mode is bit upside/down, means I cant mount USB, wipe anything, cant Partition SD Card,
Recovery Mode Reason:
I was on EHNDROIX V 14.1.24 and Unfortunately Tried to Flash Gingerbread (F1 Galaxy S2 V7).
I placed F1 Galaxy S2 V7 in internal SD and went into recovery and tried to flash, it started and after few seconds stopped, saying "Partitioning error" After that i lost my old ROM, Lost Root Access, Now Phone is just stucked at Samsung Logo.
So, was just curious is there any Magic Word that can Flash my i9000?
Any method, any expert who can give suggestion....
Thanks in Advance Guys
hasanin.xaidi said:
Problems:
1. USB Port is Buggy, Cant connect to 0din or PC. I can just charge it.
Click to expand...
Click to collapse
solve USB problem by following [Tutorial] How to resolve micro USB connection problems [unknown USB device][code 43]
Check this out! Links to useful Guides and " Banned " Documentaries
Hi guys,
So I'll tell you the whole story here. I was on Lollipop, fully rooted with working XZDR recovery but phone seemed laggy so I decided to give it a full format with the newer firmware. So I backed up everything. Booted into recovery. Formatted the whole phone, then took out the SD card to load on the zip file from the PC. On inserting it, it wouldn't be detected so I tried to reboot into recovery using the inbuilt option but forgot that recovery too would have been deleted. Since then its just stuck on the Sony logo. It reboots by keeping the Power button and Volume Up pressed, but to no avail. I tried to flash the image using Flashtool but it doesn't recognize the phone when I try to connect it in Fastboot using the Volume Down during Reboot method. Nor do I get a blue LED on the phone. I guess it isn't entering Fast boot.
Please help out since its my daily driver. Help appreciated. Thanks
Oh hey guys managed to restore using Flashtool. Tried booting phone into Flash Mode again and idk how it worked this time. Breathing a sigh of relief.
Could you please explain in detail how did you managed to get out of bootllop....it seems i sucked exactly like you & now clueless....
First of all, try repair it with Pc Companion. If that doesn't work, try with flashtool.
Keep in mind, to enter flash mode, press volume down button and insert usb cable.
tried PC companion & got error 2003 (Unlocked Bootloader & rooted wont work it seems)
Flashtool, will give a try again....
As of now, i am able to go to the fastboot & can open files on my PC when connect phone via USB cable....
Phone not booting up normal/recovery mode....It just stucked with boot loops
Tried flashtool---Ended up with errors as attached pic
As i cant bootup my phone...USB Debugging option cant be ticked
I was running SlimLP (unofficial) while bricked my phone....
Anything on that please....
pranavd1980 said:
Tried flashtool---Ended up with errors as attached pic
As i cant bootup my phone...USB Debugging option cant be ticked
I was running SlimLP (unofficial) while bricked my phone....
Anything on that please....
Click to expand...
Click to collapse
Try installing Flashtool ver 0.9.10.2beta4 - you can see in this tutorial section #5: Device connected with USB Debugging off, ergo you dont have to have USB Debugging on: http://forum.xda-developers.com/xperia-z/general/tutorial-how-to-flash-stock-roms-t2240614
Norup58 said:
Try installing Flashtool ver 0.9.10.2beta4 - you can see in this tutorial section #5: Device connected with USB Debugging off, ergo you dont have to have USB Debugging on: http://forum.xda-developers.com/xperia-z/general/tutorial-how-to-flash-stock-roms-t2240614
Click to expand...
Click to collapse
if that is the case, i think that fsc script is the issue....can you highlight something on that????
pranavd1980 said:
if that is the case, i think that fsc script is the issue....can you highlight something on that????
Click to expand...
Click to collapse
Not sure what you mean....... all I can say is, Flashtool 0.9.10.2beta4 does not require USB Debugging to be turned on to work and I definitely didnt turn USB Debugging on before starting the root process. Later yes but not before.
Try it or not, thats up to you.....
Your LG Magna(H502) stuck on lg logo or bootlooping follow this guide to fix your device
Requirements:
USB Cable
LG Driver
LG FlashTool
MegaLock.dll
H502F Stock ROM
Let's start
1.Install the LG Driver
2.Install LG FlashTool and don't run it yet
3.Copy MegaLock.dll and replace in the folder LG FlashTool (C:\LG\LGFlashTool)
4.Turn off your device(remove battery and put it back to be sure its off)
5.Press and Hold the Volume UP button,plug in the USB cable and hold until you see "Firmware Update" you are now in download mode
Don't plug into usb 3.0 port and try other ports if getting issues
6.Open Device Manager on your PC
Go on "Ports (COM & LPT)" if the driver is installed properly, you will see "LGE Mobile USB Serial Port (COMxx)"
We need to change the COM port number to 41
Double click on "LGE Mobile USB Serial Port"
Go to Port Settings Tab and click Advanced
Change COM Port Number to COM41 and click OK
Disconnect USB cable,wait a few seconds and reconnect or reboot back in download mode to check if the drivers are working properly
7.Open LG FlashTool as admin
Tick the Select Manual Mode box
Extract LG Magna H502F.rar
Click the DLL "....." button and select the DLL found in the extracted folder(LGH502f_20150416_LGFLASHv190.dll)
Click the S/W add button and select the file with the .tot extension(LGH502fAT-00-V10a-CIS-XX-MAR-16-2015+0.tot)
Don't touch anything else and press ok
Flashing will format the phone all data will be lost
8.Click on the Yellow Arrow Button at the top left and it will start the flashing process
When you see ready in a few seconds you will be asked to disconnect and reconnect the cable and it will start flashing
It will take some time
During the flashing process, the phone will reboot itself and will display "MiniOS Factory Reset Status".Don't worry about it
When you see pass in FlashTool and Factory Reset Status 3 on your phone means the flashing process is completed
Disconnect the cable and remove the battery
Power on your phone and enjoy your working phone again (Don't forget to disconnect USB cable else if you didn't close the FlashTool it will go back in download mode and flash again)
Fixing problems
Factory Reset Status 2 and download fail
Method 1
1.Disconnect the cable and take out the battery after some seconds insert back
2.Press and hold both the power button and the volume down and hold until LG logo appears release the buttons and immediately press and hold both buttons again to go in Factory Reset
3.Choose Yes, then Yes again, the phone will reboot
Method 2
1.In step 7 where we are setting up the FlashTool change the action mode to Board DL instead of Upgrade DL
2.When the flashing is done your phone will reboot to the AAT Screen
3. Hold down power button and press normal boot (+power) your phone will reboot. (dont forget to disconnect usb cable or close the FlashTool)
LGE Mobile USB Serial Port (COMxx) doesnt appear on my device manager..help me please??
danvelle said:
LGE Mobile USB Serial Port (COMxx) doesnt appear on my device manager..help me please??
Click to expand...
Click to collapse
Install LG Drivers from here : https://sourceforge.net/projects/avicohh/files/Android/LGUnitedMobileDriver_S51MAN313AP22_ML_WHQL_Ver_3.13.2.exe/download
danvelle said:
LGE Mobile USB Serial Port (COMxx) doesnt appear on my device manager..help me please??
Click to expand...
Click to collapse
Try installing the driver when you are in download mode or try other ports in your computer.If it still doesn't work try this driver http://oceanhost.eu/x1b0tjlhzw1z/LGUnitedMobileDriver_S51MAN313AP22_ML_WHQL_Ver_3.13.2.exe.htm
May the stock ROM work with h500f ?
Geralt1232 said:
May the stock ROM work with h500f ?
Click to expand...
Click to collapse
Nope
is this v10a? which ROM can be rooted and TWRPed?
xd
as I can install the KDZ I have the LG H502G And not catch any of that model Dll !! Help!!
danvelle said:
LGE Mobile USB Serial Port (COMxx) doesnt appear on my device manager..help me please??
Click to expand...
Click to collapse
You have to enable "Show hidden devices"
I lost data connection often when playing games or using any app can this problem solved by installing stock rom again? Plzz tell me the solution
Trying to get rid out TWRP
If I ever flash stock firmware, does custom recovery/TWRP be removed ?
yes.it will be replaced with stock...
Sent from Valhalla
Lg magna
My lg magna is not booting.
I tried installing a custom ROM it showed that it was done but its not booting now. Its not even booting to recovery mode. I've not tried flashing the a ock ROM but will it work.will it boot in download mode?
go to view option appear on that window and click on 'show hidden devices'
danvelle said:
LGE Mobile USB Serial Port (COMxx) doesnt appear on my device manager..help me please??
Click to expand...
Click to collapse
Reply::go to view option appear on that window and click on 'show hidden devices'
Hello, I have the following problem. As in every other thing ive done to this phone (root, installing twrp, installing xposed) I always thought my model was LG-H502F. Though, my model is LG-H500F, I bought it from Greece, I recently bought Huawei P8 lite 2017 for myself and I gave my old LG to my father, he tell me that sometimes it lags and he is right. I think it lags because I uninstalled Xposed (flashed the uninstall zip using twrp) and also removed root, because he didnt need those things in his phone. The question is: Is there somewhere I can get the stock LG-H500F zip and what guide should I use? Ive been searching for a while now and can't find many topics related to LG-H500F. Thanks
Aneom7331 said:
Hello, I have the following problem. As in every other thing ive done to this phone (root, installing twrp, installing xposed) I always thought my model was LG-H502F. Though, my model is LG-H500F, I bought it from Greece, I recently bought Huawei P8 lite 2017 for myself and I gave my old LG to my father, he tell me that sometimes it lags and he is right. I think it lags because I uninstalled Xposed (flashed the uninstall zip using twrp) and also removed root, because he didnt need those things in his phone. The question is: Is there somewhere I can get the stock LG-H500F zip and what guide should I use? Ive been searching for a while now and can't find many topics related to LG-H500F. Thanks
Click to expand...
Click to collapse
https://lg-firmwares.com/lg-h500f-firmwares/
just find the country you are in.
I found this page earlier but can you import the kzd file to LG Flash tool? I didn't test this but, I guess it works. Thanks for replying
Aneom7331 said:
I found this page earlier but can you import the kzd file to LG Flash tool? I didn't test this but, I guess it works. Thanks for replying
Click to expand...
Click to collapse
yes. it will )
Hi, I'm in the same situation as Aneom7331, indeed I have a bricked LG Magna H500F and I'm trying to flashing a stock firmware. Where should I put the .kdz file in the lg flash tool 2.0.1.6? Moreover, the .kdz file has not a .dll file together with it, Thanks in advance
Someone have link to stock for h502y?
i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second
aljthab said:
i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second[/QUOTE try connecting it to the PC, if it doesn't show anything on PC then just hand it over to the lenovo service center and blame it on the device that it stopped booting :silly:. I thought i had bricked my device but they did something and gave it to me in 3 to 4 days and that was done under the warranty no extra charge and don't confess that I had rooted ur device , If u tell them that they will try to extort money from u :crying:
Click to expand...
Click to collapse
aljthab said:
i did something Stupid and my Z2 Pro dead
e LED there is flash yellow for 0.1 second
Click to expand...
Click to collapse
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
kerei said:
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
Click to expand...
Click to collapse
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
same issue with zuk z2
adriano1593 said:
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
Click to expand...
Click to collapse
Hello there... Any solution you found? I am stuck with my zuk z2 in same situation ?? any help ?
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
eryenakgun said:
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
Click to expand...
Click to collapse
Hi,
Thanks for your quick response.
The Hardware ID: USB\DEVICE_DESCRIPTOR_FAILURE
"Error Message": This device has been stopped because it has reported errors. (Code 43)
An error occurred while requesting the USB device descriptor.
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
OtakuLi said:
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
Click to expand...
Click to collapse
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
m_atze said:
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
Click to expand...
Click to collapse
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
OtakuLi said:
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
Click to expand...
Click to collapse
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I don't want to destroy my PC (3000 bugs)
m_atze said:
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I won't destroy my PC (3000 bugs)
Click to expand...
Click to collapse
oh well, good luck
OtakuLi said:
oh well, good luck
Click to expand...
Click to collapse
I will report the result.
OK. I made the deepflash cable.
After using it there is no difference between pressing one of the button combinations I recently mentioned (VOL+ or VOL- or PWR).
The phone will be detected as Unknown device. After intalling my modified driver to match the unknown ID, QFIL don't detect the COM Port.
Hello had the same problem, only with the difference that my battery was not completely discharged.
What has helped:
1 Start QFIL Tool
2 Press the volume +
3 Connect the original cable to the PC
4 QFIL Tool recognized the phone and I could play an original Rome.
Mfg
Ps. Is now the battery cover (glass) broken?
No, I used a hairdryer, a razorblade, plastic tool and a suction cup to lift the backcover glass.
The glass is fully intact no damages.
You have good nerves. I would not have expected that.
But in the end, it does not matter if it does not start anymore.
Thank you again for your great instructions for playing and rooting the mobile phone.
I hope you get your phone back.
Mfg
Good and bad news
The guy unbricked the phone successfully, I received it today.
Now I have an other problem:
The phone is very very slow and laggy now.
The problem occurs everywere, Recovery, boot (the bootlogo laggs), booted System, also the test mode laggs now
Furthermore the sceen flickers sometimes and at the right side the sceen is mirrored sometimes.
Did anyone has an idea?
What I did today:
reflash through qfil
1.9.104_ST
2.3.044_ST
ZUI_2.5.335_ST
Hi m_atze, I am exactly in the same situation as You. After using deep flash cable method, I got "unknown usb device (device descriptor request failed)". Could You tell me what was the solution to unbrick the phone?
Hey all,
I have Zuk z2pro z2121. I wanted more than stock ROM so I downloaded zui 2.5.344. I unlocked bootloader n rooted my phone as well as installed TWRP. "Tool All in one" PC software helped me to carry out above with ease.
While playing around I clicked "Lock Bootloader" and phone got switched off with indicating continuous blue light. I tried pressing vol down + power + Home button, and several other combination but didn't help. When I pressed power button for long, I got Zuk logo onscreen with a white flash on indicator for 1 sec and then again the blue light indicator.
After a little RnD after pressing power button till I got white flash for 3 times and the blue light got completely off. I don't know what to do further. I have backup of my boot , recovery and ROM. Kindly suggest.
Shoaib
Press and hold volume - and power . Release power, after vibration you can release the volume -. You will be in that menu https://ibb.co/f3vOHm . Go to device manager and check if pc recognize your phone https://ibb.co/bHqZOR . Open CMD in adb folder and write adb devices https://ibb.co/cwCg3R . Then adb reboot edl . You are i EDL https://ibb.co/cvjiHm . Use Qfil to flash stock rom
Didn't work...
Thanks for responding. As said, tried pressing Vol + Power and never got any vibrations. Tried Up vol + power, tried Down vol + power. No vibrations.
When I press power button with any combination, this is what happens,
After Approx 15 secs - 1 white light flash in place of blue along with ZUK pic on d display (stays approx 1 sec)
Still keeping power button pressed
After approx 7-8 secs - same as above
Still keeping power button pressed
After Approx 15 secs - 1 white light flash in place of blue along with ZUK pic on d display (stays approx 1 sec)
But now after this third time of flash, blue light appears and after 4-5 secs disssappears. If I leave the button only at this time, the blue light doesn't comes back.
If I leave the power button before or after this sequence, the blue light doeanon the indicator doesn't goes off at all.
What is happening when you connect phone with pc ? Is there any reaction ?
No reaction from PC.
I tried connecting to PC, earlier Tool all in one immediately use to detect, n now there is no response from the PC or the software after making USB connection.
Sir,
As I said earlier, I clicked lock bootloader, n when the screen went off, I disconnected the phone from PC. There is a possibility of the boot partition getting damaged or so. Kindly assist.
Rgds
There aren't any ways to enter in fastboot or recovery , even in service menu . I think you should try deep flash cable to enter in EDL .
Will do as u say. Just one last thing, when I checked device manager in my PC, it showed the phone as other devicez "QUSB XXXX". Question is,
1. Any possibilities of recovery without going for a deep flash, as I got to learn it first.
2. Other part is, my phones battery seems to be drained now. So, it won't be a problem for a deep flash.
Could you give some print screen ?
The matter is that you must switch your phone to edl . Try this yet . Your phone must be turn off .
Press only volume up button for 10 sec and while keeping it pressed,connect phone to PC . Hold volume up until your PC finds a new hardware . It should be android phone - ShenQi composite adb interface . If it doesn't work I have no more ideas apart from df cable . This cable works on Zuk z2 and I think it should works on our Zuk z2 pro
Sir,
I managed to connect the phone via USB as 9008. Miflash not supporting my ROM. Will download Stock ROM n then try with QFIL and MiFlash as well. Thanks for all your support. Will keep u posted about the progres. XML file is not found in any ROMs I have. Miflash some error also but detecting the device. Is there any other tool similar to Miflash, which I can try..
Rgds
First use QPST/Qfil . Follow this guide https://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
Do all steps .
Good day.
I tried QFIL as well as Mi flash tool. Both showing errors. QFIL displaying Qualcomm HS USB QLoader 9008. But when downloading content , it shows Sahara error with even initiating the installation. After browsing a bit, started eMMC software download, and found displaying COM20 No phone connected. Can u assist me to fix this. I mean the phone must be in download mode. But how ?
Miflash, on the other hand shows Hello packet error. Don't know how to fix.
Things I did to fix above errors,
1. Copied ROM to Qualcomm/ bin file
2. Copied ROM to C:/
3. Tried using different USB ports
4. Tried different USB cables
5. Uninstalled n reinstalled USB driver, adb n fastboot, qpst, n miflash many a times along with restarting my PC.
None of the above helped.
I think, if eMMC software download starts displaying COM20 Phone connected, then the issue might be sorted out.
Kindly assist.
Rgds
DrTahseen said:
Good day.
I tried QFIL as well as Mi flash tool. Both showing errors. QFIL displaying Qualcomm HS USB QLoader 9008. But when downloading content , it shows Sahara error with even initiating the installation. After browsing a bit, started eMMC software download, and found displaying COM20 No phone connected. Can u assist me to fix this. I mean the phone must be in download mode. But how ?
Miflash, on the other hand shows Hello packet error. Don't know how to fix.
Things I did to fix above errors,
1. Copied ROM to Qualcomm/ bin file
2. Copied ROM to C:/
3. Tried using different USB ports
4. Tried different USB cables
5. Uninstalled n reinstalled USB driver, adb n fastboot, qpst, n miflash many a times along with restarting my PC.
None of the above helped.
I think, if eMMC software download starts displaying COM20 Phone connected, then the issue might be sorted out.
Kindly assist.
Rgds
Click to expand...
Click to collapse
U need ufs flash not emmc. Change programmer in qfil.
I have a some experience with miflash but I use it for xiaomi . I've never flashed my zuk z2 pro by miflash . If you want to use miflash use 2016.03.30 and run it on PC with win 64 . Create a folder on c: for example "zuk" and copy to that all contents of unrar Qpst/Qfil zui rom . If you have Qualcomm hs usb 9008 that means your phone is in edl ( download mode ) . Good luck
I appreciate all ur support....
As suggested, tried Miflash 30.03.2016 also. This ones showing class not registered.
No of things i did to overcome this errors.
1. Changed my PC to developer mode. Allowed portable device connections n stuff.
2. Visual studio C++ 2010 was installed along with Qualcomm driver, i believe thats sufficient.
3. Disabled my Firewall.
4. Downloaded n copied some atl70.dll file to my syswow64 folder as well as sys32 folder.
Tried all flash tools again after these changes....Same negative results.
Any further advices !!!
Regards
It's fault of drivers . Go to device manager and chose qualcomm hs usb 9800 and update driver automaticly . The second matter concerning of flashing by qpst/qfil - why did you put rom in qpst location ? . It must be for example on desktop in one folder . The simplest path is better . Don't use spacebar . Load content you must chose from that rom . Don't use other location . It's not necessary . Could you give some screenshots with qfil errors
DrTahseen said:
I appreciate all ur support....
As suggested, tried Miflash 30.03.2016 also. This ones showing class not registered.
No of things i did to overcome this errors.
1. Changed my PC to developer mode. Allowed portable device connections n stuff.
2. Visual studio C++ 2010 was installed along with Qualcomm driver, i believe thats sufficient.
3. Disabled my Firewall.
4. Downloaded n copied some atl70.dll file to my syswow64 folder as well as sys32 folder.
Tried all flash tools again after these changes....Same negative results.
Any further advices !!!
Regards
Click to expand...
Click to collapse
Did u use ufs flash in qfil instead of emmc?
Starchm said:
Did u use ufs flash in qfil instead of emmc?
Click to expand...
Click to collapse
Yups !!! I already did with Meta Build Type selection. Didnt Help. I tried to search for mbn file also to try emmc but cudnt find so was stuck with ufs....
mar.ur said:
It's fault of drivers . Go to device manager and chose qualcomm hs usb 9800 and update driver automaticly . The second matter concerning of flashing by qpst/qfil - why did you put rom in qpst location ? . It must be for example on desktop in one folder . The simplest path is better . Don't use spacebar . Load content you must chose from that rom . Don't use other location . It's not necessary . Could you give some screenshots with qfil errors[/QUOTE
https://forum.xda-developers.com/attachment.php?attachmentid=4339940&stc=1&d=1511421690
https://forum.xda-developers.com/attachment.php?attachmentid=4339941&stc=1&d=1511421690
https://forum.xda-developers.com/attachment.php?attachmentid=4339942&stc=1&d=1511421690
Click to expand...
Click to collapse