So I have had the Z3 Compact since first week of release and from day 1, it had a tiny chip (could call it a nic) on the leading edge of the front bezel just above the magnetic port. I decided to keep it, but the number of these indentations has increased to 12.
One of these nics has flaked further to almost 2mm diameter by the top left corner.
All of the marks are on the front leading long bezel, both sides.
I always put my phone in a pocket without other items
I always lie my phone face up.
I don't use any kind of stands or holders in the car
No other phone (Moto X, Nexus 5, Nexus 4, Razr I) has ever suffered anything like this.
There are no marks on the back or front faces (cheap screen protectors on both, which usually scratch/mark easily)
I suspect its poor adhesion of the top black paint layer on the bezel, but cannot prove it obviously.
I can send it back to Sony, but they may say its not manufacturing fault and thus charge me £25 for sending it back without repairing (I find this disgraceful)
I have little experience with Sony customer service or care so it's a risk I don't really want to take.
Question, has anyone elses phone suffered in a similar way?
Or have positive (or negative) experience with Sony UK?
Thanks in advance.
You can send it back to Sony, most of the times they charge you with shipping costs yup.
Manufacturing error or not, but also try to look from their side, if it were easy to get your device repaired without costs or even replaced, more people would do it, even if it was their mistake.
So in the end they can't just believe everyone.
They will repair it when you send them, but thy might ask for repairing fees.
I'm noticing the same thing. I keep the phone in my pocket as well, but I do keep it with a leather keyholder (pretty soft leather), so I'm surprised that there are any chips/nicks at all. I actually have 3 right now, first one in just about the same place as you (above the magnetic charging port), a smaller one above the power button, and the last one in the bottom right corner of the phone.
I always assumed the metal bezels on these phones was powder-coated aluminum, which is pretty tough. Anyone know what is actually is?
Dsteppa said:
You can send it back to Sony, most of the times they charge you with shipping costs yup.
Manufacturing error or not, but also try to look from their side, if it were easy to get your device repaired without costs or even replaced, more people would do it, even if it was their mistake.
So in the end they can't just believe everyone.
They will repair it when you send them, but thy might ask for repairing fees.
Click to expand...
Click to collapse
Yes I understand that, but I know that these ever increasing faults are not of my doing, but I cannot prove it.. Therefore, it is possible (maybe probable) that Sony will offer an expensive repair or simply send it back with the total cost to me being close to £30.
pipspeak said:
I always assumed the metal bezels on these phones was powder-coated aluminum, which is pretty tough. Anyone know what is actually is?
Click to expand...
Click to collapse
I believe they are painted plastic but I might be wrong.
I've said before that this is one of the few annoyances I have with the build quality of this phone. The Z3 doesn't have the front and back plastic bezels as the metal frame attaches directly to the front and back glass. I don't mind the transparent plastic on the sides of the Z3C but I don't like that they needed to use plastic front and back bezels.
To answer the OP's question, i also have light scuffs and small chips on the front plastic bezel of my Z3C but the back is near perfect at the moment. If I'd have known the build quality in these areas was lacking I'd have waited until I had a case before i used it but it's too late now.
I've decided to return the phone for repair (hopefully under warranty) and have ordered several cases (I usually do this once I am satisfied that the phone is a keeper). Will keep you posted.
Related
Hi,
I personally love my xperia X1. Its a lovely piece of sleek hardware, can be easily overclocked and has a good solid metal chassy. I bought a black one from rogers and I love it. I personally havent had any cracking issues or anything, in fact my phone has been dropped on pavement 2 times and in deep snow once, and emerged without even a scratch.
Because I hate frequent hardware changes Id like to keep my xperia for a full five years and would like to buy a second phone as they are really becoming cheap now. I have had my eye on the silver phones for a while, but know they are more prone to cracking. Particularly phones made in weeks 44,45 and 46 right?
Are there any silver phones that have had this issue corrected yet and been relreaed?
When buying a phone and shopping is there a way to tell which phones will have the cracking issue? Serial or batch numbers on the box mabye.
If I am concerned should I just stick to the black ones?
Finally other than ebay does anyone know where I can get a cheap new or refurbished X1?
Any help is appreciated.
hahahhahahahahahahaha
I have a black xperia and it cracks like crazy xD and i didn't drop it once xD
Hi, if the cracking is whats got you concerned, why don't you try getting just the housing? there's guides on how to replace it, I've done it myself. Replaced both the ribbon cable and the housing.
I still have my silver X. bought it at bethefirstx1 (1st day). my housing has been replaced once because of crack. I never bumped my phone nor dropped it. but I have cracks all over it:
1. the dreaded volume button crack (2nd time after replacement)
2. the camera button crack
3. the middle area crack (rumored to have been cracked due for using a car stand, I don't have car stand but I got the crack on the same location)
4. the camera part crack up to the top of the phone
The only thing left for me to have is the crack on the stylus area and the crack on the earphone plug.
So after these years, what I can tell about it is it still cracks due to user mishandling (please correct me if I'm work I already rant a lot of times on the crack thread)
but I found out that whenever you change your battery/take off your memory card, you either use your fingernail to open the cover on one of the four areas where you can slip it. That actually inclines the cover and tilts it on the side where your fingernail opened it. Thus it results to the cracking of the opposite trapeziodal area (either the volume or camera part)
I had my keyboard replaced and the camera housing had the crack after it was replaced. (I'm thinking it was from the technician's part of re-assembling it)
Lastly, the metallic middle portion of the phone chipped off:
I think from the leather case that came with my X1, the middle part of it is exposed and I wear 'em clipped on my belt. I guess that how got it to chip off, whenever you reach your phone on your belt side you actually hold it on the expose area pressing your thumb to it to lever your fingers on the magnetized leather case to open up. For more than 3 years of doing it everyday, I guess that the reason for my crack on the metallic area.
If you live in the UK you could pay a visit to CEX also known as Entertainment Exchange, they also have a website... I bought my x1 from them about three months ago, and everything they sell comes with a 12 month guarantee be it second user or brand new.
just buy the black one, the silver ones seem to crack a lot easier. Or just get another phone that's better, they should be cheap now.
I got mine for $120 so can't complain.
Christopher888 said:
Hi,
I personally love my xperia X1. Its a lovely piece of sleek hardware, can be easily overclocked and has a good solid metal chassy. I bought a black one from rogers and I love it. I personally havent had any cracking issues or anything, in fact my phone has been dropped on pavement 2 times and in deep snow once, and emerged without even a scratch.
Because I hate frequent hardware changes Id like to keep my xperia for a full five years and would like to buy a second phone as they are really becoming cheap now. I have had my eye on the silver phones for a while, but know they are more prone to cracking. Particularly phones made in weeks 44,45 and 46 right?
Are there any silver phones that have had this issue corrected yet and been relreaed?
When buying a phone and shopping is there a way to tell which phones will have the cracking issue? Serial or batch numbers on the box mabye.
If I am concerned should I just stick to the black ones?
Finally other than ebay does anyone know where I can get a cheap new or refurbished X1?
Any help is appreciated.
Click to expand...
Click to collapse
I bought an silver x1i this 14 feb 2011 and it shows some crack on the battery-housing,flaking paint is my another problem . I'm still under warranty ..what should I do? I love x1 a lot than others do..
Sorry for bad english, hope you understand my problem..!
"Tough" Silver X1
I have a Silver X1 for about 3 years now, fell down 15 feet, hit a stone and has a tiny little dent on the screen, never had cracking problems until 2 weeks ago, fell out my hand, 3 floors down, ricocheted off a handrail and landed on concrete pavement, one crack upper right hand corner, and well usual wear and tear, the bright chrome siding wore off due to car keys in same pocket.
Don't know whether my phone actually is tough, or plain dumb luck.
Anyone have suggestions for dealing with cracks on an out of warranty TP?
I sent my Touchpad back in February when it was in warranty, and got a new case. Then the girlfriend liked the fit on my TP better and insisted that I trade her for hers which hadn't had any issue and hadn't been back for repair.
Well, it now has cracks. There are two cracks leading from the speaker openings onto the back of the case that I was ignoring. Now there's a crack from one of the speakers to the front, which is more threatening since if the other side of that cracks the thin piece will come off...
It's like the poor TP is falling apart. I've had it in the official HP case the whole time and am extremely careful with it, of course, everyone knows that doesn't really help. It seems some of the cases were just destined to crack!
So is there anything to be done? Does anyone know how much HP charges if you PAY them to fix it? Probably too much.
What about a Skinomi case like this: http://www.skinomi.com/hp-touchpad-carbon-fiber-skin-protector.html - will that help keep piece next to the speaker from cracking the rest of the way, and maybe at least.. *sigh*... hide the other cracks?
I have a feeling that I will eventually have a pile of loose electronics in my hand here....
lotherius said:
Anyone have suggestions for dealing with cracks on an out of warranty TP?
I sent my Touchpad back in February when it was in warranty, and got a new case. Then the girlfriend liked the fit on my TP better and insisted that I trade her for hers which hadn't had any issue and hadn't been back for repair.
Well, it now has cracks. There are two cracks leading from the speaker openings onto the back of the case that I was ignoring. Now there's a crack from one of the speakers to the front, which is more threatening since if the other side of that cracks the thin piece will come off...
It's like the poor TP is falling apart. I've had it in the official HP case the whole time and am extremely careful with it, of course, everyone knows that doesn't really help. It seems some of the cases were just destined to crack!
So is there anything to be done? Does anyone know how much HP charges if you PAY them to fix it? Probably too much.
What about a Skinomi case like this: http://www.skinomi.com/hp-touchpad-carbon-fiber-skin-protector.html - will that help keep piece next to the speaker from cracking the rest of the way, and maybe at least.. *sigh*... hide the other cracks?
I have a feeling that I will eventually have a pile of loose electronics in my hand here....
Click to expand...
Click to collapse
I know what you mean about the cracking - I think all TP users share our remorse.
I don't know what HP charges, or even if that's an option with them, considering how quickly they dropped any sort of support for us after launch.
What I've done in regards to the cracking is just dab a small amount of super glue on/in the cracked plastic (while paying mind to the speakers!) and hold it there for a hot second. Then, I throw back on the official HP case and pretend the cosmetic issue doesn't exist...... Until I find a new crack..... and then, it's rinse and repeat.
As for the Skinomi protector, I don't have one (although highly contemplating getting one, now) but, you can find it cheaper on Amazon. However, this SKIN got better reviews, plus it's cheaper!
/sigh
I also had my case replaced due to cracking around the speakers. From the sound of it, it may just always happen. I plan to just put dabs of super glue if it starts again, and not worry about it. I've heard some people saying they think it's from using a case (ie putting too much pressure on it), and others saying it's just a manufacturing defect. Unless it completely falls apart, it shouldn't really cause problems, hopefully. If anything, maybe just put it in some case, even like a TPU wrap.
the cracks on my speakers have gotten way worse
the cracks propagated to the back side, plus, cracks appear on the microusb connector as well
i feel it's cuz of the official case that's causing it
the tablet is always home, does not get that much use, it's mostly just sitting around
anyways, looking at the skinomi link, it looks pretty promising
it will hide the cracks for sure, plus, i have always hated the matte finish on the back because it's a dirt magnet
anonxlg said:
i feel it's cuz of the official case that's causing it
the tablet is always home, does not get that much use, it's mostly just sitting around
Click to expand...
Click to collapse
Honestly, though I can't see *how* the official case can be causing the problem.
Many people had cracks when their devices were brand new, and didn't have the case because it still cost like fiddy bux at the time. HP even tried sending out cases to people as a preventative.
Also, I "manage" four Touchpads. So far, mine is the only one that has cracked - twice now. The others also use the official case. However, only two of them get used heavily, mine and the girlfriend's. She insists that I must be rough with my Touchpad, but I am definitely not rough with it - I am extremely careful. Her case shows scars from being dropped, chewed on by dogs(!), etc... but no cracks.
I wonder if there's a "usage scenario" that causes something internal to heat causing the cracks. But I've never noticed my TP getting excessively hot. It's just whether or not you got a good backplate or not.
When I had my first Touchpad repaired under warranty, the new backplate it came with had a fit much better than any of the others we'd bought. It fit perfectly flush with the glass and had no uneven spots around the edge. None of the other Touchpads we have matched that level of fit. Unfortunately, my girlfriend took that Touchpad to gift to someone else, and left me with one of the ones that had a less than perfect fit. I think the level of fit of the original backplate has a lot to do with whether or not it cracks.
I did find a place online that sells replacement backplates, but they're like $50 a pop... Not worth it even for those of us that paid $200 for our 32gb touchpads. http://www.portatronics.com/product_info.php?info=p10245_HP-Touchpad-Backplate-Part-Only.html -- I don't know anything about that site or the part. Oddly enough, it also isn't listed if you search by category on their website. I could only find it by google search. It lets me add it to the cart, but who knows if it is actually available.
Shortly after I noticed the cracks I bought a Stealtharmor cover for the back while it was on sale.. Nearly a year later and the cracks haven't gotten any worse.
I have read lots of threads and comments on the Internet regarding screen cracking on the z3c but most are dating back to early 2015.
As I am now considering buying a Z3C does anyone know if improvements have been made by Sony to address these issues for the 2016 models?
Thanks for any comments.
Nothing has changed. On the bright side, replacing said-glass is very cheap and easy to do. On the minus-side. Say bye-bye to any form of water-resistance. This long with the Z3C: I've grown to accept this phone won't be water-resistant unless I use a case because the seals and IP-68 rating is only for fresh-water and the rating completely depends on the ability of flap-seals and sealant of the back cover to to do its job. I hope I can convince you to disregard water-resistance factor in your purchase. Notably because Sony won't cover any repairs if the damage is a result of water-damage(personal experience). That way, you can swap back glass covers as you please. They go for like $2.
My z3c screens right top corner today unglued. Lasted for about 8 months since purchase, without case, without any water interference. Still under warranty, sending it for repair.
alpha-niner64 said:
Nothing has changed. On the bright side, replacing said-glass is very cheap and easy to do. On the minus-side. Say bye-bye to any form of water-resistance. This long with the Z3C: I've grown to accept this phone won't be water-resistant unless I use a case because the seals and IP-68 rating is only for fresh-water and the rating completely depends on the ability of flap-seals and sealant of the back cover to to do its job. I hope I can convince you to disregard water-resistance factor in your purchase. Notably because Sony won't cover any repairs if the damage is a result of water-damage(personal experience). That way, you can swap back glass covers as you please. They go for like $2.
Click to expand...
Click to collapse
Thanks for the reply, if I understand you correctly replacing the back glass is not a big issue and is cheap, but what about the front screen? I did have a quick search around the net and it looks quite complicated and expensive to replace the front one.
Have you done the front one yourself?
Thanks.
vilx01 said:
My z3c screens right top corner today unglued. Lasted for about 8 months since purchase, without case, without any water interference. Still under warranty, sending it for repair.
Click to expand...
Click to collapse
Yep, mine has unglued as well, after 7 months of usage (bought it brand new), I am sending it for repair also. When my warranty expires, I will replace case on my own, because I have black one, and I want black screen + white case
bmg777 said:
Thanks for the reply, if I understand you correctly replacing the back glass is not a big issue and is cheap, but what about the front screen? I did have a quick search around the net and it looks quite complicated and expensive to replace the front one.
Have you done the front one yourself?
Thanks.
Click to expand...
Click to collapse
I service my own phones often enough to kind of say that replacing your own front screen is easy to do if you're starting out with this phoneYou take out the front-screen the same way you take apart the back screen.. As long as your motherboard components are in good condition like the USB Port, antenna, SIM/MicroSD slots, and the battery(cause this is glued very well to the motheboard), nearly everything on the Z3 Compact is expendable and easily replaceable.
alpha-niner64 said:
I service my own phones often enough to kind of say that replacing your own front screen is easy to do if you're starting out with this phoneYou take out the front-screen the same way you take apart the back screen.. As long as your motherboard components are in good condition like the USB Port, antenna, SIM/MicroSD slots, and the battery(cause this is glued very well to the motheboard), nearly everything on the Z3 Compact is expendable and easily replaceable.
Click to expand...
Click to collapse
I've been using Z3C (15W33) since early september and this phone has really rough life. I mean working in very hard conditions (very cold outside > pretty warm inside the house) and I never really cared about it even when I know there are problems with the glass. Also I have a custom s-line case and that's the only protection... I dropped the phone twice or three times...
but it's still running pretty nice and there are no signs of any damage, the glass is more than OK
This morning I was cleaning my phone (getting rid of the finger prints/smudges) while standing up when it slipped out of my hand and hit the tiled floor. Everything is fine except the screen (which is cracked). Screen works fine but is unresponsive no matter where I press or touch the screen. How much does a Z3 Compact replacement screen cost? I searched around and it seems it is about $100?
Screen replacement costs in Poland +/- 135$
(authorised sony service)
Yes' it's hard to get original one cheaper than 100-120$. You can search for some Chinese replacement cause sometimes it looks quite similar to original one but You must check it before buying. Last time I had a client with Z1c replacement screen which he bought for 40$ and there was no white color, everything what should be white was purple.
Voids warranty, cheap replacement
Got mine from here replacebase dot co dot uk (can not post links ), of course you void your warranty if you do it yourself.
Parts are good quality till now. I advice to order a back glass too, I broke mine when taking it out and had to reorder again (costs approx 6 pound).
Next time just heat up back glass with hair dryer and You wont break it.
Chamelleon said:
Next time just heat up back glass with hair dryer and You wont break it.
Click to expand...
Click to collapse
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Thanks for the replies.
I'll be getting the repair done from the official Sony shop/distributor I bought the phone from. Just wanted to get an idea of how much it "should" cost before I approach them.
m4mbax said:
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Click to expand...
Click to collapse
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Foxhunter123 said:
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Click to expand...
Click to collapse
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
m4mbax said:
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
Click to expand...
Click to collapse
Doh!!! ? I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) ?.
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Most pre-glued adhesive stickers on back are useless. Now everytime I change back in Xperia Z, Z1, Z2, Z3 and compacts I need to remove pre-glued sticker and change it to original one. Many times I had complaint on it from my clients saying that back glass came off. So it's better to order original back glass or just original adhesive.
Foxhunter123 said:
Doh!!! I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) .
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Click to expand...
Click to collapse
Good
Mine came with the adhesive ON the screen, I used that one, I didn't have a separate one. Be extra careful when 'placing' the adhesive where it belongs because you can not remove it once place (okay maybe slightly). Its important that it fits on the first to first and a half try. More adhesive means thicker layer --> glass will stick out
Anyway, most of the stories you read online are partially BS, the phone will work even when the glass is a tiny bit loose or when the adhesive rotated and is a bit thicker in one place. In my eyes, when you dared to order, you are very much capable of assemble the parts.
In btw, ordered new glasses today, hope my two left hands fix it this time.
PS: A lesson I learned on a friends Galaxy S2, do NEVER EVER try to use force when something sticks or is not as loose as in a video. Google or ask another person maybe you just dont do the trick. A connector didnt want to come off so we used a lever to lift it, CLICK, the place where the lever levered broke the board... :silly:
Edit 1: I think its not necessary to HEAT it, it just has to be a lil bit warmer than in your pocket or when calculating heavily. 30s under a hairdryer will be more than enough i guess.
Forgot to update this thread. I received my fixed phone last week. They replaced the screen and even the "bumpers" around the phone for $98. They even delivered the phone to my home free of charge. Looks brand new, all the minor dings I had on the phone are gone.
On another note, I also bought my first iPhone. Got an Space Gray iPhone 6s 128 GB with the official/Apple leather case for the 6s. Got it last Thursday. Been playing around with it a lot and, overall, I love it. Deciding on whether to keep my Z3 Compact as a back-up phone or just sell it. But geez, does the iPhone 6s load games and other apps fast (thanks to its NVMe storage).
So I like just about everything about the Sony Z compact line of phones but durability wise I have been unlucky. My first Z3 compact died from water damage and my 2nd one has a screen that is ready to fall off the device.
I choose to buy a HTC U11 to replace my Z3 compact as I have never owned a HTC phone before and thought I would try something different.
What I would like to ask here though is it worth trying to fix the Z3 compact to sell or not?
The only way to protect this phone:
The phone bends 0.1mm causes the phone screen to start opening. So it's not suitable for jeans pockets.
I remedied this by using an anodized aluminium bumper and tempered glass both sides.
Sony does a very bad repair of it's phones, and the issues will return, and their parts are expensive.
It is better to do it yourself and use B7000 glue, use plenty, easily removable for future repairs, no heat, clothes pegs, wait 48 hours before removing pegs or turning on the phone. And look for the best grade of screen with frame, Sony uses two manufacturers for its screens.
My Z3C has a screen that is lifting. This thread and others seem to indicate that fixing the screen is not hard but hardware is not my thing at all...
Would a phone repair place (in a shopping centre) be able to do this kind of repair? Is the phone much different to other phones that people would take in for screen replacements?
I don't care about the loss of waterproofing. The screen isn't even falling out, just lifted in the corner. I don't want to send the phone anywhere and be without it, or have it come back changed in unexpected ways...
a1291762 said:
My Z3C has a screen that is lifting. This thread and others seem to indicate that fixing the screen is not hard but hardware is not my thing at all...
Would a phone repair place (in a shopping centre) be able to do this kind of repair? Is the phone much different to other phones that people would take in for screen replacements?
I don't care about the loss of waterproofing. The screen isn't even falling out, just lifted in the corner. I don't want to send the phone anywhere and be without it, or have it come back changed in unexpected ways...
Click to expand...
Click to collapse
Phone shops including Sony themselves have difficulty in repairing this particular phone, I think any phone shop can do this repair, but, they must use the B7000 glue or similar, or silicone, and not the red tape they usually use, it's useless, as this phone can heat up, or the blue z3c ready cut tape is not so good either. And if you get the wrong screen (clone), the colours will not be as good.
Many phone repairers have the clone screens that are thicker than the original.
The screen sometimes is actually bent, along with the body, check on a flat surface.
Always buy a good screen together attached with the body, and never by itself.
So armed with this knowledge and or hardware, you could go talk with a phone repairer... The first 3 times, shop, but maybe the fourth repair, try doing it yourself, it's as easy as opening a PC, just smaller, just follow z3c repair guides and youtube, when you're ready. When attempting to repair the phone, for the very first time, do it over hours, maybe over the weekend, and not one sitting.
If you start loosing patience, leave it for a while etc.
[emoji12]
I got so comfortable with opening my phone, I put extra 0.3mm copper plates on the processor and gpu with Cooler Master Extreme Fusion paste etc. Lol.
But it's good to have an already damaged motherboard to work on.
Z3C LOS Omni Oreo
My screen is still working fine. Just lifting.
I do have some old phones I could practice on, assuming they have the same glass sandwich construction.
I will go look for some videos...
a1291762 said:
My screen is still working fine. Just lifting.
I do have some old phones I could practice on, assuming they have the same glass sandwich construction.
I will go look for some videos...
Click to expand...
Click to collapse
?
Z3C LOS Omni Oreo
I put up with my screen for a long time but eventually the glue gave out and I had no choice. It was good, then bad, but ultimately ok.
I didn't have any trouble taking the glass off the first time because the glue was barely hanging on. I had a look and noticed that the headphone jack's glue was also failing. Probably why it was becoming unreliable. I glued that and reseated the screen cable and it worked fine while sitting there so I glued everything on again.
It was a poor first attempt. I had both too much glue (blobs that leaked out) and not enough to actually seal around much of the screen. No problem. I took the glass off again and glued it again. This time I followed the instructions closer and glued the front screen before connecting the ribbon.
The second gluing was good but something with the ribbon was wrong because it only worked when I pressed on the lower part of the screen. Sigh.
Taking the glass off after a good glue was much harder. I finally got the spudger under the glass but I moved it sideways before removing the suction thing. It was too much pressure for the glass. The good news is that it was the rear glass and only the bottom half shattered. I got the rest off and started on the front.
Now that I knew to be more careful, I got the front off OK. Reseat. Test and working. I glued the front on first again, without disconnecting the cable. Tested and working. I glued the half back I had on (covers the camera).
Its working!
I use a case so the back isn't even a problem, but I ordered a new back from China (cheap). The headphone Jack seems better. I put a new screen protector on. In some ways the phone is rejuvenated.
I was apparently not careful enough when taking off the screen though. I appear to have some marks on my screen now. It's minor, probably won't notice during normal use, but there if you look.
I'm so glad to have my phone back. I've been using an iPhone for the last 3 weeks.
Thanks for the tips.
Edit: The hands free speaker works again too. Bonus