Tried updating to 6.0, stuck at Huawei loadingscreen - Huawei Mate S

Afternoon gents.
So yesterday i tried to update my Mate S with 5.1 Android to the 6.0 version with Huawei´s Firmware. After adding the Dload file to the mobilephone and starting the update sequenze, the phone does a double boot, basically does the first boot as usual, after loading the first boot it reboots and does a second boot. The second boot just gets stuck at the Huawei loadingscreen.
Ive tried to clear both the cache folder and do a factory reset, both did not work. I tried to do a recovery from the Hisuit software from Huawei, but as my phone is not supported by the software, that did not work either. (And yes, i did get the phone into the Fast Boot menu).
So from what i can see, im left with doing a manuel reset of the ROM. This is not something im very good at, allthough i do know alot about PCs, phones is a whole nother area i have not exlored yet.
So i was wondering if anyone here had any help they could provide me with how i can fix this for this specific phone. I do have the stock ROM and the newest ROM with 6.0 Android.
Ive been fooling around with ADB and SP Flash Tools, but i constantly get stuck as im not too sure what im doing.
Any help is greatly appreciated!

Edits
Just a few Edits:
The ADB i simply could not figure out how to use, the SP Flash Tools on the other hand looked quite simplistic and easy to use. Problem i had with the SP Flash Tools is that i only have the Update.APP file, but i did need a Scatter file (and possibly some other files), this is where i got stuck using this software.
Also, i forgot to mention. Whenever i turn off the phone by holding inn the ON/OFF Buttion, it automatically restarts and tries to boot again. Basically i cannot turn it off.

hi..
try to get a full 5.1.1 rom for your mate s..
which cust version do you have?
eu is c432
global is c900
and all others are provider based firmwares or other countries..
so you need to get your proper firmware which is for your country, then take an external sd card..format it on pc (fat32), put a folder on it named "dload", inside this you put the update.app (no need for other files)..
then start your phone by pressing all three hardware buttons (power, vol+ & vol-) at the same time and hold them until the update screen is showing up..
then it should flash/install this firmware..
after that try to start the OTA updater by huawei..
if this doesn't work, take the correct update.app (full version) of the next higher version (in my example it was c432b145 (android 5) - c432b321 (android 6 beta) - c432b361 (android 6 final) ) and do the same as before..
good luck
Gesendet von meinem HUAWEI CRR-L09 mit Tapatalk

blueIBI said:
hi..
try to get a full 5.1.1 rom for your mate s..
which cust version do you have?
eu is c432
global is c900
and all others are provider based firmwares or other countries..
so you need to get your proper firmware which is for your country, then take an external sd card..format it on pc (fat32), put a folder on it named "dload", inside this you put the update.app (no need for other files)..
then start your phone by pressing all three hardware buttons (power, vol+ & vol-) at the same time and hold them until the update screen is showing up..
then it should flash/install this firmware..
after that try to start the OTA updater by huawei..
if this doesn't work, take the correct update.app (full version) of the next higher version (in my example it was c432b145 (android 5) - c432b321 (android 6 beta) - c432b361 (android 6 final) ) and do the same as before..
good luck
Gesendet von meinem HUAWEI CRR-L09 mit Tapatalk
Click to expand...
Click to collapse
Hi, thanks for the reply.
To be honest, im not completly sure which i have, but considering i bought it in Norway i supose the EU version is the correct: eu is c432
I did not know you coul boot from an external SD card. this made things alot easyer. Ill drive out to my office where i have a micro SD card coverter and try this fix. Ill bring all the Firmwares and lets hope it all works!
Cheers for the reply man, might just be my lifesaver.

Hello again,
I tried what you suggested with both the stock ROM and the new updated ROM, but it did not seem to work. The problem i get is when the update starts, it reaches 5% when it verifies the software, then i get a "Software install failed!".
Please note i had this problem before i tired this, problem first occured when i did a factory reset of the device. So i belive the phone is still not booting from the SD card, but from thge phone itself as before. How do i solve this?

I could also add. before i did the factory reset, the update did work, but it still got stuck on the boot logo.

I gues ill be sending the phone inn for service tomorrow unfortunatly, cause i cannot figure this out. Thanks though!

Related

Cannot upgrade P7-L07 with EMUI 2.0

Hi,
a friend of mine has got in China a P7 with a strange EMUI 2.0 firmware (I always knew that P7 came with 2.3 since the first version). I wanted to upgrade it to the EMUI 3.0, then I downloaded the package from emui.com, I extracted the dload directory and copied to the internal memory (the same procedure I succesfully did with mine) but when I booted it holding Vol-, Vol + and Start button I just went into the stock recovery interface.
I though was a problem of the recovery, then I restarted with adb into bootloeader mode but the screen was all empty except for "fastboot mode" wrote at the bottom. When I tried to flash another recovery I got an error saying that flashing the recovery was not allowed.
Anyone knows what the problem is?
Thanks in advance
locked bootloader..
blueIBI said:
locked bootloader..
Click to expand...
Click to collapse
And also is resisting to any attempt to unlock: do not give Product ID so I cannot produce the unlocking code, neither are working all methods I found on the web. I may have to give up
maybe there is a firmware for your p7-L07 like there is for the p6-u06 where you can flash a so called unicom version and first downgrade and then upgrade/update..
and hopefully this downgrade unlocks the bootloader..
just my thoughts..
blueIBI said:
maybe there is a firmware for your p7-L07 like there is for the p6-u06 where you can flash
Click to expand...
Click to collapse
Thanks blueIBI, the problem is how to flash it, since the normal way do not work. After copying the dload directory on the phone memory, if I use the system menu to perform local upate or I reboot by pressing Vol+ Vol- Start I always end up in the recovery menu, the firmware gets never installed.
Will try harder.
jimmi61 said:
Thanks blueIBI, the problem is how to flash it, since the normal way do not work. After copying the dload directory on the phone memory, if I use the system menu to perform local upate or I reboot by pressing Vol+ Vol- Start I always end up in the recovery menu, the firmware gets never installed.
Will try harder.
Click to expand...
Click to collapse
Are you sure this is original P7 not some chinese crap looking like P7?
mrcs64 said:
Are you sure this is original P7 not some chinese crap looking like P7?
Click to expand...
Click to collapse
The phone belongs to a friend of mine. I own another P7 and they look exactly the same. It came in the original box with everything, so I have no doubt that it is original.
The fact that it has EMUI2.0 make me think that it was one of the first released to the market. The phone is working fine, just it is not upgrading on-line and I cannot find a way to upgrade it manually. I will try contacting Huawei support.

Please help me im desperate (p9 unrooting)

Hey all.
I am trying to unroot and re lock my bootloader so my phone is back to its normal state
I have wiped all data on twrp and re flashed with 136.
That isn't the issue,
Whenever I go to change the theme it doesnt let me, the stock icons are big and ugly and werent the stock ones I had before.
Does anybody have a guide on how I can remove all traces of this root because its not letting me get rid of these ugly icons.
Reflash from externe SD card ?
Verstuurd vanaf mijn EVA-L09 met Tapatalk
can you please elaobarate? i have the same problem...
buljo said:
can you please elaobarate? i have the same problem...
Click to expand...
Click to collapse
I think that what he said is this:
- Create a dload folder on sd card root
- Copy update.app (from 136) to dload folder on sd card
- Force an reflash: power off, then vol up+vol down+power
- After flashing, go to huawei updater and update to the last official version for your phone
This is what I've done with mine. And ended with bootloader locked and everything as factory again.
Hope it helps, but if you search the forum you will find a lot of info about this procedure.
iLukey96 said:
Hey all.
I am trying to unroot and re lock my bootloader so my phone is back to its normal state
I have wiped all data on twrp and re flashed with 136.
That isn't the issue,
Whenever I go to change the theme it doesnt let me, the stock icons are big and ugly and werent the stock ones I had before.
Does anybody have a guide on how I can remove all traces of this root because its not letting me get rid of these ugly icons.
Click to expand...
Click to collapse
If u wipe data and flash u need to include the hw folder to with the firmware in dload folder when u flash to get rid of the ugly icons and get Themes to work.
jamorimpt said:
I think that what he said is this:
- Create a dload folder on sd card root
- Copy update.app (from 136) to dload folder on sd card
- Force an reflash: power off, then vol up+vol down+power
- After flashing, go to huawei updater and update to the last official version for your phone
This is what I've done with mine. And ended with bootloader locked and everything as factory again.
Hope it helps, but if you search the forum you will find a lot of info about this procedure.
Click to expand...
Click to collapse
You have to flash stock recovery via fastboot before this method of complete reflashing firmware. Otherwise flashing process may fail and end up on eRecovery screen.

Stuck in bootloop

I got a free P9 from a family friend so i decided to tinker around with it.
I successfully unlocked the bootloader flashed twrp and installed SU on it but then I wanted to try the unofficial CM rom on it. But I wasn't getting any signal with it so then i tried to go back into stock firmware which was posted on xda (at the time i didn't know i had the wrong model). After that Playstore wasn't working so tried using another stock firmware that was on xda but then i found the right model that i had (VIE-AL10C00176) but now it's stuck in a boot loop. It would boot up (doesn't show that i have an unlocked bootloader anymore) and then it would restart. Occasionally it boots up into erecovery. I've tried downloading "latest firmware and recovery" from this but it's still stuck in a boot loop. Any idea how I might fix this? (lack of hindsight cause i've done this a lot on other phones but i didn't prep a back up). I'm pretty sure I left USB debugging on before all of this I have yet to test if i can reflash twrp and try flashing another rom to see if this fixes anything (any thoughts?). Any help would be appreciated thanks.
Hello. I would try this way:
1. download a complete dload version from http://www.huaweifirm.com/firmware/p9-plus-vie-l09/
2. unzip it, inside there is a dload folder..
3. format a micro SD card and copy the dload folder on it
4. shutdown the phone. If it does not shut down don't worry.. go to next step
5. insert the micro SD card
6. keep pressed all three buttons (volume+, volume- and power) until it starts flashing
Let me know if it works..
antonio2009 said:
Hello. I would try this way:
1. download a complete dload version from http://www.huaweifirm.com/firmware/p9-plus-vie-l09/
2. unzip it, inside there is a dload folder..
3. format a micro SD card and copy the dload folder on it
4. shutdown the phone. If it does not shut down don't worry.. go to next step
5. insert the micro SD card
6. keep pressed all three buttons (volume+, volume- and power) until it starts flashing
Let me know if it works..
Click to expand...
Click to collapse
That will not work, he has the Chinese version AL10.
Sent from my VIE-L29 using XDA Labs
---------- Post added at 06:14 PM ---------- Previous post was at 06:02 PM ----------
bkzz said:
I got a free P9 from a family friend so i decided to tinker around with it.
I successfully unlocked the bootloader flashed twrp and installed SU on it but then I wanted to try the unofficial CM rom on it. But I wasn't getting any signal with it so then i tried to go back into stock firmware which was posted on xda (at the time i didn't know i had the wrong model). After that Playstore wasn't working so tried using another stock firmware that was on xda but then i found the right model that i had (VIE-AL10C00176) but now it's stuck in a boot loop. It would boot up (doesn't show that i have an unlocked bootloader anymore) and then it would restart. Occasionally it boots up into erecovery. I've tried downloading "latest firmware and recovery" from this but it's still stuck in a boot loop. Any idea how I might fix this? (lack of hindsight cause i've done this a lot on other phones but i didn't prep a back up). I'm pretty sure I left USB debugging on before all of this I have yet to test if i can reflash twrp and try flashing another rom to see if this fixes anything (any thoughts?). Any help would be appreciated thanks.
Click to expand...
Click to collapse
Try this guide for P8 it works on P9 to. Just follow the guide and use the VIE-AL10C00 firmware.
http://forum.xda-developers.com/huawei-p8/how-to/guide-how-to-unbrick-huawei-p8-failed-t3260704
Sent from my VIE-L29 using XDA Labs

[Tutorial] Rollback from N to MM for C432 devices

Many people have problems to get back from C432B336 to C432B160/151/etc. so I decided to briefly explain, how to rollback using official Huawei tools. I am not responsible for any damage, soft bricks, hard bricks, etc. Internal storage will be wiped clean! This method worked for me, I did it twice on L31 and L21, both times without any problems. All firmware files come from official Huawei support for Germany, UK, and Poland. Here we go:
1. Preparation
A few things are necessary before we can rollback:
SD Card (needed to apply update)
Huawei Rollback File
For L31C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93787&siteCode=de
For L21C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93800&siteCode=pl
For L11C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93764&siteCode=uk
Full OTA Software File (for the system You want to finally end up with)
L31C432B160: http://download-c1.huawei.com/download/downloadCenter?downloadId=93803&siteCode=de
L21C432B160: http://download-c1.huawei.com/download/downloadCenter?downloadId=93802&siteCode=pl
L11C432B161: http://download-c1.huawei.com/download/downloadCenter?downloadId=93804&siteCode=uk
PC/Mac and USB cable
2. Going to C900B300
Rollback file will change Your software info to C900B300. As far as I know, this is a specific firmware key, that alows to fully update firmware to any other version. What you need to do:
Download and unpack Huawei Rollback File for Your device (links in chapter 1)
Copy "dload" folder from unpacked file to Your SD card
Turn off Your phone and turn it back on, holding POWER, VOL+ and VOL- buttons
Now, Your phone should apply update from SD card, and reboot
In Your phone, go to "Settings" -> "About Phone". If Your software version is LXXC900B300, everything is fine, and You can proceed
2. Switching to Marshmallow
Download and unpack Software File for Your device (links in chapter 1)
Remove all files from "dload" folder on Your SD Card, and copy "UPDATE.APP" from the file You just unpacked to this folder
Turn off Your phone and turn it back on, holding POWER, VOL+ and VOL- buttons
Now, Your phone should apply update from SD card, and reboot
Second reboot may last a while, but eventually You'll see a popup informing about removing user data
Next reboot will bring You a fresh install of MM,
Done
Again, I'm not responsible for any bricks, crashes, etc. If You want more information or help, please, leave a comment in this thread.
SteadyDisorder said:
[*]In Your phone, go to "Settings" -> "About Phone". If Your software version is LXXC900B300, everything is fine, and You can proceed
Click to expand...
Click to collapse
Hmm, update process of rollback file went fine, but in settings>about, it says build number is NRD90M test keys..
Should I proceed to next step?
EDIT: never mind, I did second step, and it worked like a charm
SteadyDisorder said:
Many people have problems to get back from C432B336 to C432B160/151/etc. so I decided to briefly explain, how to rollback using official Huawei tools. I am not responsible for any damage, soft bricks, hard bricks, etc. Internal storage will be wiped clean! This method worked for me, I did it twice on L31 and L21, both times without any problems. All firmware files come from official Huawei support for Germany, UK, and Poland. Here we go:
1. Preparation
A few things are necessary before we can rollback:
SD Card (needed to apply update)
Huawei Rollback File
For L31C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93787&siteCode=de
For L21C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93800&siteCode=pl
For L11C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93764&siteCode=uk
Full OTA Software File (for the system You want to finally end up with)
L31C432B160: http://download-c1.huawei.com/download/downloadCenter?downloadId=93803&siteCode=de
L21C432B160: http://download-c1.huawei.com/download/downloadCenter?downloadId=93802&siteCode=pl
L11C432B161: http://download-c1.huawei.com/download/downloadCenter?downloadId=93804&siteCode=uk
PC/Mac and USB cable
2. Going to C900B300
Rollback file will change Your software info to C900B300. As far as I know, this is a specific firmware key, that alows to fully update firmware to any other version. What you need to do:
Download and unpack Huawei Rollback File for Your device (links in chapter 1)
Copy "dload" folder from unpacked file to Your SD card
Turn off Your phone and turn it back on, holding POWER, VOL+ and VOL- buttons
Now, Your phone should apply update from SD card, and reboot
In Your phone, go to "Settings" -> "About Phone". If Your software version is LXXC900B300, everything is fine, and You can proceed
2. Switching to Marshmallow
Download and unpack Software File for Your device (links in chapter 1)
Remove all files from "dload" folder on Your SD Card, and copy "UPDATE.APP" from the file You just unpacked to this folder
Turn off Your phone and turn it back on, holding POWER, VOL+ and VOL- buttons
Now, Your phone should apply update from SD card, and reboot
Second reboot may last a while, but eventually You'll see a popup informing about removing user data
Next reboot will bring You a fresh install of MM,
Done
Again, I'm not responsible for any bricks, crashes, etc. If You want more information or help, please, leave a comment in this thread.
Click to expand...
Click to collapse
It works with unlocked bootloader?
I failed on the first step, it says "Software install failed! Incompatibility with current version. Please download the correct update package." I'm on VNS-L21C432B336
edyy1111 said:
It works with unlocked bootloader?
Click to expand...
Click to collapse
I think it will, but haven't tested it
Acoca said:
I failed on the first step, it says "Software install failed! Incompatibility with current version. Please download the correct update package." I'm on VNS-L21C432B336
Click to expand...
Click to collapse
Try downloading rollback package for Your country, maybe that will help. You can find them on Huawei support site.
Did it yesterday. Works perfect for me. THX for the links
Done today and it worked perfectly (rollback from c432b335 to c432b161).
Bye, folks!
First file installed, rebooted... stuck seeing the Huawei logo... :/
Edit: it booted but the build number says i'm on test-keys and still android 7...And missing half of the apps
So I don't know if I can continue with the rollback
Chippie_83_ said:
First file installed, rebooted... stuck seeing the Huawei logo... :/
Edit: it booted but the build number says i'm on test-keys and still android 7...And missing half of the apps
So I don't know if I can continue with the rollback
Click to expand...
Click to collapse
Are you sure you used correct rollback package?
SteadyDisorder said:
Are you sure you used correct rollback package?
Click to expand...
Click to collapse
At the moment I'm not so sure anymore! But I am sure I used the L31 version, which is the one I need...
Edit: solved! See this thread
I can't downgrade to 6.0
It always fails when I try to apply the first step, and I can't find an package for my country(Romania) VNS-L31C432B336. I tried all the possible packages, and it doesn't work...
I can't downgrade to 6.0 too...i fail the fist step(the install upgrade goes well but the reset doesn't), i'm quite sure i used the right rollback package. I'm now stuck, hiSuite doesn't work(it doesnt' recognize the device or something like that) eRecovery cannot retreive the package to reset. I really don't know what to do.
Update: the phone is not bricked,there's some part of a OS similar to android,witout keybord, navigation bar and notification bar. Is it a clone??D: i should have wiped cache and factory reset(somehow)but nothing seems to work, everything fail.
SteadyDisorder said:
Many people have problems to get back from C432B336 to C432B160/151/etc. so I decided to briefly explain, how to rollback using official Huawei tools. I am not responsible for any damage, soft bricks, hard bricks, etc. Internal storage will be wiped clean! This method worked for me, I did it twice on L31 and L21, both times without any problems. All firmware files come from official Huawei support for Germany, UK, and Poland. Here we go:
1. Preparation
A few things are necessary before we can rollback:
SD Card (needed to apply update)
Huawei Rollback File
For L31C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93787&siteCode=de
For L21C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93800&siteCode=pl
For L11C432 (EU): http://download-c1.huawei.com/download/downloadCenter?downloadId=93764&siteCode=uk
Full OTA Software File (for the system You want to finally end up with)
L31C432B160: http://download-c1.huawei.com/download/downloadCenter?downloadId=93803&siteCode=de
L21C432B160: http://download-c1.huawei.com/download/downloadCenter?downloadId=93802&siteCode=pl
L11C432B161: http://download-c1.huawei.com/download/downloadCenter?downloadId=93804&siteCode=uk
PC/Mac and USB cable
2. Going to C900B300
Rollback file will change Your software info to C900B300. As far as I know, this is a specific firmware key, that alows to fully update firmware to any other version. What you need to do:
Download and unpack Huawei Rollback File for Your device (links in chapter 1)
Copy "dload" folder from unpacked file to Your SD card
Turn off Your phone and turn it back on, holding POWER, VOL+ and VOL- buttons
Now, Your phone should apply update from SD card, and reboot
In Your phone, go to "Settings" -> "About Phone". If Your software version is LXXC900B300, everything is fine, and You can proceed
2. Switching to Marshmallow
Download and unpack Software File for Your device (links in chapter 1)
Remove all files from "dload" folder on Your SD Card, and copy "UPDATE.APP" from the file You just unpacked to this folder
Turn off Your phone and turn it back on, holding POWER, VOL+ and VOL- buttons
Now, Your phone should apply update from SD card, and reboot
Second reboot may last a while, but eventually You'll see a popup informing about removing user data
Next reboot will bring You a fresh install of MM,
Done
Again, I'm not responsible for any bricks, crashes, etc. If You want more information or help, please, leave a comment in this thread.
Click to expand...
Click to collapse
if you have oeminfo l31c636 you can share for me thanks
Success!
I actually did this exactly the same way with the help of Huawei Customer Service. They saved my life and this tutorial will save many more!
markositoo said:
I actually did this exactly the same way with the help of Huawei Customer Service. They saved my life and this tutorial will save many more!
Click to expand...
Click to collapse
They didn't answer to me..
robi10101298 said:
They didn't answer to me..
Click to expand...
Click to collapse
That is really strange. I received an answer from them the very next day after I sent my e-mail describing my problem. Then it was just a matter of a few hours and constant e-mail exchange with them, talking about the problem, and eventually they found a way to fix it and it worked like a charm. The fix is exactly the same as in this thread.
Followed the guide to rollback from vns-l31c432b336 to b161 and worked flawlessly: just to give more details on the installation progress, if you see an error message during data erase in the first dload installation, don't mind it, reboot and proceed to next step, if you did follow exactly what the OP says, you will have no problem with last installation!
Thanks a lot for the tutorial, saved me lot of time and efforts!
Thanks!
works perfect!
Thanks a lot!
markositoo said:
That is really strange. I received an answer from them the very next day after I sent my e-mail describing my problem. Then it was just a matter of a few hours and constant e-mail exchange with them, talking about the problem, and eventually they found a way to fix it and it worked like a charm. The fix is exactly the same as in this thread.
Click to expand...
Click to collapse
I finally received a message from them.. They said my phone it's not made for Romanian market and they can't help me with this problem.. Very nice..

Need help to flash stock rom on P SMART 2019

Hi everyone,
I need to flash stock rom on a huawei P SMART 2019
Unfortunately I followed all steps on this link : https://firmwarefile.com/huawei-p-smart-2019-pot-lx1
I installed all drivers, software but when I put in donwload mode, it shows ADB interface ready but not downloading on the phone or sometime I get a fastbook status failed
If anyone had a little trick with this
Thank you.
If you’re still looking for a solution, I reverted a Huawei P Smart 2019 (POT-LX1 but may also be known as POT-L21) back to 9.1 stock ROM by:
1. Downloading the firmware from here: https://androidhost.ru/search.html
2. Putting the 3 zip files from the firmware in a dload directory on a clean SD card then putting it in the phone (please note that some documentation instruct you to put UPDATE.APP in the dload directory. This didn’t work for me.)
3. Powering on the phone while holding both the volume buttons down
The phone would reboot in EMUI recovery, check the presence of the firmware on the SD card, and install it if correct.
Hi
Unfortunately I can't test anymore since I don't have the demo unit with me but thank you
breversa said:
If you’re still looking for a solution, I reverted a Huawei P Smart 2019 (POT-LX1 but may also be known as POT-L21) back to 9.1 stock ROM by:
1. Downloading the firmware from here: https://androidhost.ru/search.html
2. Putting the 3 zip files from the firmware in a dload directory on a clean SD card then putting it in the phone (please note that some documentation instruct you to put UPDATE.APP in the dload directory. This didn’t work for me.)
3. Powering on the phone while holding both the volume buttons down
The phone would reboot in EMUI recovery, check the presence of the firmware on the SD card, and install it if correct.
Click to expand...
Click to collapse
hey..
i have flashed a rom from this site and now my pot-lx1 only boots in recovery.. no erecovery works, no other update.. every time i try to updste again with sd card it fails with error.. so i think i flashed wrong dload firmware.. i was wondering that the first try to flash with sd card and dload works perfectly.. phone says to verify update and pass verifying the firmware on sd card.. update success but phone doesn start now..
i tried factory reset again and this doesnt work..
can u please give me the name or the link for the fitmware files that worked for u?
thanks
I think it was Huawei_P_Smart_2019_POT-LX1_9.1.0.314_C432E8R4P1_Firmware_EMUI9.1.0_05015PRL_Dload.zip
breversa said:
I think it was Huawei_P_Smart_2019_POT-LX1_9.1.0.314_C432E8R4P1_Firmware_EMUI9.1.0_05015PRL_Dload.zip
Click to expand...
Click to collapse
thanks, but does not work for me.. update files from sd not verified from phone.. no update with these files possible..
i tried some other files and find some which updates perfectly..but almost the same.. phone says:
"Your Device has failed verification and may not work properly"
maybe it is bricked for ever...
I hope you'll find a solution. I can't help you any further as I've spent way too much time on that ****ty phone (stay away from Huawei/Honor/Oppo in the future).

Categories

Resources