Database Develop

[Q] (Q) Galaxy tab P1000L wont turn on

O my problem is i was trying to flash OVERCOME Icarus and following the guide on the overcome site i downloaded the stock v5 file unziped and started the included odin in download mode selected the files as instructed set repartition and pressed start. After couple minutes odin gave me a green PASS and rebooted my phone but it wont turn on soft keys are on but screen is of. If i press the power button the keys turn of. Conecting it to power outlet (original included charger) turn on soft keys after a few secs but no battery icon displayed.
After about 30 mins in this state i tried plugging it to my pc (windows 7x64Ultimate) and windows made the sound that it detected something but i cud not check what hardware it detected and odin did not detect device.
Is this a SOFT-Brick or a HARD-Brick and how can i correct my problem if possible
Edit: ok when i plugg it in windows Device manager shows SAMSUNG Android USB Modem, and SAMSUNG Android composite adb interface. Also if i start kies it tries to connect but after a while gives me a device not responding to resolve this issue reboot the device. Odin still does not detect it
Edit2: Ok tried going tru command prompt adb with adb devices command and it gives me a device conected in recovery mode i guess the is still hope still if some1 can help ill apreciate it

i was gonna reply you now , if you wait 1 second with your pm , you could see me reply you
1st of all and this is the important , overcome is not for P1000L my prove is :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
if odin can't recognize it then sorry i can't do you anything but you can try this "
Check to see if the device is actually "Hard" bricked by leaving it plugged into charge for atleast 4 hours via a mains supply (NOT USB).
If above doesn't work you will need to send your Tab To Samsung To Fix it For you or visit this link. "
sorry for your lost dude , you better read carefully later the guides , to be sure batter than to be sorry .
good luck

Rotobackup
Ok managed to get the tab in download mode with screen on(had to replace bootloader)... and now im trying a full hemidall flash from a stock roto-backup i made before i started flashing will update......

chinchulin said:
Ok managed to get the tab in download mode with screen on(had to replace bootloader)... and now im trying a full hemidall flash from a stock roto-backup i made before i started flashing will update......
Click to expand...
Click to collapse
how you managed it to go into download mode ? btw glad to hear that

download mode
looks like the tab was booting but the screen wasnt turning on i replaced the kernel with one found in post #1 from this treadhttp://forum.xda-developers.com/showthread.php?p=14728425#post14728425 and instalation continued still no screen the followed instructions from post#4 of same thread and got screen to turn on but stuck at galaxy tab boot screen, got fed up and im restoring my original rotobackup using heimdall 1.1 frontend the bar at heimdall shows 100% but no other success or failure message been like that for bout 10mins device screen show download bar but i dont see any advance btw im at the phone-yellow triangle-pc download screen

that is cool , simply you are a Worrier
did you unplugged or not yet ?
sooner or later you gonna do

still nothing
damm this tab used odin to flash my roto backup of original rom and nothing normal boot goes past galaxy tab screen into operator(telcel:mexico) animation and then gets stuck in samsung logo.
Recovery mode shows following errore:cant mount /dev/bñock/mmcblk0p2 (invalid Argument)
E:install_aplication_for_customer: cant mount DATA:
Good news looks like a software brik bad news=a really bad software brik any help will b thanked and apreciated

i think you need to flash your firmware " http://www.samfirmware.com/apps/auth/login?why=pw&try=1&wp=1&next=WEBPROTECT-p1000.htm" download it from this link ans flash it with PIT FILE

Finally
Ok Im a very happy tab owner now dont really know what worked but i tried the rom from samfirmware and the same so i retraced my steps got overcome in there again managed to get the sexy voice withoout screen went back to samfirmware at this point the error changet to cant mount dev sdcard or something like that so i went back to my own rotobackup and was back on last error.
I was almost thinking of sending it for repair when (and i dont know why i did) in the factory recovery menu i pressed home on the wipe cache option i got android with sign so i get desperate and press home dunno how many times and sudenly the cache was wiped i did the same on factory reset and after that my tab booted into my operator rotobackup(rooted ofc).
Guess I will stick to froyo for now and thanks for the help

Telcel
I'm anothere desesperated user that tried to update the Galaxy Table P1000L toandroid Gingerbread, but screen is not working anymore, I hate my self for trying doing this, What should I do? I wasn't able to download rotohammer tools as http : // files. deodexed. com/ModADroid-Galaxy-Tablet/Rotohammer/JME/ is not working anymore, help!!!! please!!!!

So... same problem here.... My tab p1000l bricked and then when i finally got the answear the battery got drained... so... if i understand it correctly if it was not a hard brick i can charge already if i plug it for at least 4 hours to charge?

[Q] N7000 bricked?

Hello, peeps!
So I was when starting an application, my phone doesn't respond. Tried the power button and it didn't work so I removed the battery and placed it back in.
Here's when my nightmare starts. My phone is stuck at the "GT-N7000" screen, and I cannot proceed further. I'm unable to start Recovery Mode (Vol Up + Power + Home), and only Download Mode works.
However, I tried flashing stock roms, Odin showed no progress even after almost 2 hours.
What seems to be the issue? Is it a hard brick?

Questions should be in the Q&A section.
Is odin able to detect the phone.. ( the port square in odin turns yellow/blue?).
check if there are any Kies processes running in the task manager.. kill them, restart odin and restart phone in download mode and try again.

nokiamodeln91 said:
Questions should be in the Q&A section.
Is odin able to detect the phone.. ( the port square in odin turns yellow/blue?).
check if there are any Kies processes running in the task manager.. kill them, restart odin and restart phone in download mode and try again.
Click to expand...
Click to collapse
Hi, how do I move the topic?
Odin is able to detect it. Checked and no Kies processes running at all.

where is Odin getting stuck?

nokiamodeln91 said:
where is Odin getting stuck?
Click to expand...
Click to collapse
stuck at the NAND Write part, and the progress bar shows no progress at all (the green bar thing). Could this mean hard brick?

do you have warranty? If yes, take it to Samsung and tell them to rectify it. If no warranty then, you will need to get into recovery may be by flashing a kernel using odin.

nokiamodeln91 said:
do you have warranty? If yes, take it to Samsung and tell them to rectify it. If no warranty then, you will need to get into recovery may be by flashing a kernel using odin.
Click to expand...
Click to collapse
Wow...thank you for such quick replies!!
Nope, no longer in warranty..Can I have a link to the kernel file?
Thank you so much!

Before you go about this.. try a reboot PC, reboot download mode phone. try a original USB cable and main USB port of pc and flash again,
If above still stops at NAND
http://forum.xda-developers.com/showthread.php?t=1901191
look for a tar.md5 file which is odin flashable. If you remember the build number of you phone, then pick that else get any JB kernel and flash using odin. check if odin gives a pass.

nokiamodeln91 said:
Before you go about this.. try a reboot PC, reboot download mode phone. try a original USB cable and main USB port of pc and flash again,
If above still stops at NAND
http://forum.xda-developers.com/showthread.php?t=1901191
look for a tar.md5 file which is odin flashable. If you remember the build number of you phone, then pick that else get any JB kernel and flash using odin. check if odin gives a pass.
Click to expand...
Click to collapse
I've flashed it, unfortunately it's stuck at NAND (kernel flash). Are there any alternatives?
Thanks!

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sorry for double posting, here's the screenshot..

you dont need to select it everywhere... just the PDA ONLY.
1. download http://d-h.st/FVh.. this is a PIT file.. select it in the PIT partition. Check it and also repartition.
2. select the kernel file in the PDA..
3. press start... (you will need to reboot into download mode every time to start flashing. so remove the battery.. reboot into download mode.. (vol down+home+power)... after you get the screen volume up to continue.. once the screen shows DOWNLOADING, then connect to pc .. open odin

Thanks again!
How long does it normally take for the entire process to complete? The progress bar of "Set Partition" isn't moving at all

There seems to be some issue with the USB Port or Cable or PC.. you need to check ...a full flash of rom takes about 5-10 mins.

use only the back usb port, don't use the front or extension usb ports, they often throw up problems.. good luck

elprix and
I tried everything suggested, but the progress bar doesn't even move
What are the symptoms of hard brick btw?
EDIT : I tried with Odin3 V3.09, and it is stated Re-Partition failed.
EDIT2 : Tried multiple files, progress bar not moving at all.

It don't write to NAND. But it still is able to set partition. Have you tried a different pc? Uninstall Kies completely and then again install Samsung usb drivers.
Sent from my GT-I9500 using xda premium

Hi everyone!
I experience a similar problem as the original poster! Yesterday my phone was fine, but then it rebooted and got stuck. Now I can only get in to "Download mode". There it says:
Odin Mode
Product Name: GT-N7000
Custom binary download: No
Current binary: Samsung Official
I've had it running Paranoid Android successfully for months and then this happened! So where do I go from here,,,? I have Odin downloaded, drivers installed, so what should I try to flash and in what order?
I would be thankful for any help - feel a bit handicapped without a phone!

316097 said:
Hi everyone!
I experience a similar problem as the original poster! Yesterday my phone was fine, but then it rebooted and got stuck. Now I can only get in to "Download mode". There it says:
Odin Mode
Product Name: GT-N7000
Custom binary download: No
Current binary: Samsung Official
I've had it running Paranoid Android successfully for months and then this happened! So where do I go from here,,,? I have Odin downloaded, drivers installed, so what should I try to flash and in what order?
I would be thankful for any help - feel a bit handicapped without a phone!
Click to expand...
Click to collapse
Exactly what happened to me! Running on PA too! Any solutions?

[Q] re-post: gt-s5830 stuck at bootloop

Hi, I am reposting here because I posted in the wrong section. If any action is required by me to have a better troubleshooting, ask please!
Hi, after one year using CM7, I decided to go back to stock rom on my galaxy ace. After flashing with odin, I keep getting stuck on a bootloop. I tried wiping cache and doing a factory reset but the problem persists. I tried unbranded stock as well as wind and vodafone, but the phone keep bootlooping. I also tried again with CM7 but the phone doesn't boot again. Please help, I believe the phone is ok but I don't know how to get out from this situation. I read several forums and all of them suggest to factory reset it, but this procedure seems to not be effective on my phone. How can I solve it?

I'd like to provide more detail in order to give a more complete description but I'm not able to know which error messages are given by the phone...I just see the samsung logo. I'm quite a newbie but I have a lot of experience with computers and electronic devices, so if anyone can point me the way, I can easily learn how to do...

gt-s5830 stuck at bootloop
ilmatte said:
I'd like to provide more detail in order to give a more complete description but I'm not able to know which error messages are given by the phone...I just see the samsung logo. I'm quite a newbie but I have a lot of experience with computers and electronic devices, so if anyone can point me the way, I can easily learn how to do...
Click to expand...
Click to collapse
Hi,
flash stock ROM,
remove sd-card,
wipe cache and do a factory reset again;
daniga74

daniga74 said:
Hi,
flash stock ROM,
remove sd-card,
wipe cache and do a factory reset again;
daniga74
Click to expand...
Click to collapse
thank you for answering. anyway I already did these steps for the whole last weekend. I tried no-brand stock rom, branded (wind) and various versions of android (2.3.3, 2.3.6, ...) of course I have countlessly factory reset the phone but the result is always the same: samsung logo loading and reloading till the end of humanity.....
any other option?

I forgot to mention that I've followed this guide: http://www.droidviews.com/how-to-in...mware-on-samsung-galaxy-ace-s5830-using-odin/
I found many smilar others on the web but the procedure is the same. Download .tar.md5 from sammobile and then flash with odin 4.38 using cooper_v1.0.ops
....but the phone keeps bootlooping.....

......time for my phone to be launched into the trash bin?

ilmatte said:
Hi, I am reposting here because I posted in the wrong section. If any action is required by me to have a better troubleshooting, ask please!
Hi, after one year using CM7, I decided to go back to stock rom on my galaxy ace. After flashing with odin, I keep getting stuck on a bootloop. I tried wiping cache and doing a factory reset but the problem persists. I tried unbranded stock as well as wind and vodafone, but the phone keep bootlooping. I also tried again with CM7 but the phone doesn't boot again. Please help, I believe the phone is ok but I don't know how to get out from this situation. I read several forums and all of them suggest to factory reset it, but this procedure seems to not be effective on my phone. How can I solve it?
Click to expand...
Click to collapse
hi
well download or i may say swap some odin versions.
Download Firmware files etc
and first select the PDA and hit Flash
Then Again Select BOOT and hit Flash Then Choose Whole Firware and Flash agaian.
If Device doesnt start charge it and then Manually Boot it UP:
HIT ThaNks

Hi, if you can access in recovery mode, do a wipe cache/dalvik cache/factory reset;
flash another ROM for S5830 model, for example S5 reincarnation;
later flash with odin the stock rom,
wipe cache and do a factory reset again;
daniga74

Hi, i have the exact same problem with my coworkers Ace gt-s5839i !
His Ace crashed in normal use and was stuck in a bootloop after the crash.
I looked up the internet and tried the factory reset/wipe without success.
Then i tried flashing several firmwares for the 5839i and even 5830i fw´s with odin v1.87 and 3.10 (took me 2 days to figure out that you need to split the fw files with odinatrix for flashing... ).
But still everytime it either freezes in a black screen after the samsung loading screen (after the model logo followed by the branding/animated Samsung logo) or shuts off and starts over the bootloop.
Is there a chance that this error is hardware-sided ? I wiped everything countless times but it doesnt change anything. What else could i try ?
I would love to get some suggestions that could do the trick !
Sorry for hijacking this thread but it fits perfect to my problem

ace_ger said:
Hi, i have the exact same problem with my coworkers Ace gt-s5839i !
His Ace crashed in normal use and was stuck in a bootloop after the crash.
I looked up the internet and tried the factory reset/wipe without success.
Then i tried flashing several firmwares for the 5839i and even 5830i fw´s with odin v1.87 and 3.10 (took me 2 days to figure out that you need to split the fw files with odinatrix for flashing... ).
But still everytime it either freezes in a black screen after the samsung loading screen (after the model logo followed by the branding/animated Samsung logo) or shuts off and starts over the bootloop.
Is there a chance that this error is hardware-sided ? I wiped everything countless times but it doesnt change anything. What else could i try ?
I would love to get some suggestions that could do the trick !
Sorry for hijacking this thread but it fits perfect to my problem
Click to expand...
Click to collapse
Hello
Well Actually if u can clear the EFS of your phone and the eMMc, it would work normally.
#Flash a Custom Recovery using Odin
#CWM much better. Go to Advanced and clear the efs and emmc there.
#Normally flash the Stock Rom using Odin or Heimdall
Hi THAAAAANNKS

RáKí Zârğãr said:
Hello
Well Actually if u can clear the EFS of your phone and the eMMc, it would work normally.
#Flash a Custom Recovery using Odin
#CWM much better. Go to Advanced and clear the efs and emmc there.
#Normally flash the Stock Rom using Odin or Heimdall
Hi THAAAAANNKS
Click to expand...
Click to collapse
Ok i downloaded the CWM Recovery but i dont know what to do in the Advanced Menu ?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks for your help !

ace_ger said:
Ok i downloaded the CWM Recovery but i dont know what to do in the Advanced Menu ?
View attachment 3337993
Thanks for your help !
Click to expand...
Click to collapse
the version of CWM you have flashed for your cooper doesnt seem to clear the Emmc and Efs etc.
If your device doesnt boot up to Download Mode then Force boot it using Heimdall Rescutor and flash the stock rom using the same tool or Odin.
In odin tick the option of NAND ERASE ALL.
Still doesnt work give me a ring on +918715031141
Hit THAAANKS button plx

galaxy s6 g920t stuck on samsung logo after flash with firmware g920tuvu3doj7 (5.1.1)

I had soft bricked my t mobile galaxy s6 g920t. i flashed it odin with the latest firmware g920tuvu3doj7 but after that the phone reboots and the android guy appears and say erasing and then the phone reboots again and gets stuck on the samsung logo.
i wiped cache partition and data/factory reset but still not use.....the phone reboots and gets stuck on samsung logo
i saw in some forum that i need to flash again with odin with the BL and AP box but the site was Vietnamese and i couldn't understand it .
any help would be appreciated...

Have you tried re-flashing the firmware?

tocirah1 said:
Have you tried re-flashing the firmware?
Click to expand...
Click to collapse
yep, tried it but still the same problem.

If you're upgrading to the latest you may have to separately flash the modem and bootloader Of the new one idk for sure though
Sent from my SM-G920T using XDA Free mobile app

lorddart said:
If you're upgrading to the latest you may have to separately flash the modem and bootloader Of the new one idk for sure though
Sent from my SM-G920T using XDA Free mobile app
Click to expand...
Click to collapse
this is my first android phone so i'm a noob , do you mean i need to flash my phone again with another files from odin?

vegeta_badman said:
this is my first android phone so i'm a noob , do you mean i need to flash my phone again with another files from odin?
Click to expand...
Click to collapse
Try waiting, sometimes can take 10-15 minutes for it to fully load. Be patient. Does it ever get past the samsung logo where it gets to white screen with Tmobile in pink animation?

tyrone1 said:
Try waiting, sometimes can take 10-15 minutes for it to fully load. Be patient. Does it ever get past the samsung logo where it gets to white screen with Tmobile in pink animation?[
i've waited for 20 minutes and still it's stuck on the samsung logo......i then go to recovery mode and shut down the phone.....No, it hasen't gone past the samsung logo, it's stuck there
Click to expand...
Click to collapse

vegeta_badman said:
tyrone1 said:
Try waiting, sometimes can take 10-15 minutes for it to fully load. Be patient. Does it ever get past the samsung logo where it gets to white screen with Tmobile in pink animation?[
i've waited for 20 minutes and still it's stuck on the samsung logo......i then go to recovery mode and shut down the phone.....No, it hasen't gone past the samsung logo, it's stuck there
Click to expand...
Click to collapse
Then yeah needs to try re-flashing. Which version of odin you using? I think there is like 3.10.
You flashing the full firmware too right? http://forum.xda-developers.com/tmo...firmware-g920tuvu3doi1-g920tuvu2doh6-t3213001 check 2nd post from this thread.
Maybe if you get a chance when you go download mode take a photo of your phone screen so can see where you at.
Click to expand...
Click to collapse

tyrone1 said:
vegeta_badman said:
Then yeah needs to try re-flashing. Which version of odin you using? I think there is like 3.10.
You flashing the full firmware too right? http://forum.xda-developers.com/tmo...firmware-g920tuvu3doi1-g920tuvu2doh6-t3213001 check 2nd post from this thread.
Maybe if you get a chance when you go download mode take a photo of your phone screen so can see where you at.
Click to expand...
Click to collapse
i'm using odin 3.10.6 and the 5.1.1 firmware that was released in oct which i know is the latest one
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse

There the problem frp lock on. So maybe try to flash firmware you were coming from first. Then get that up and running again. Then turn off frp then update after.

I think you can go into recovery and see what recovery version you on. That might help too. When power is off then hold up home and power. It will not into recovery and give you more clues.

tyrone1 said:
There the problem frp lock on. So maybe try to flash firmware you were coming from first. Then get that up and running again. Then turn off frp then update after.
Click to expand...
Click to collapse
My phone was sent from usa and i live in a different country and also i don't know what firmware the phone came with and right now i flashed with latest 5.1.1 build . so can i flash it with old firmware (5.0.2) to figure out which one works or do i need to do something else.

I would try to flash do1 full firmware then see if you can boot.
Do not attempt to flash anything older than DO1 because that boot loader can't be downgraded.
So try flashing full DO1 and see if you can boot.

tyrone1 said:
I would try to flash do1 full firmware then see if you can boot.
Do not attempt to flash anything older than DO1 because that boot loader can't be downgraded.
So try flashing full DO1 and see if you can boot.
Click to expand...
Click to collapse
i flashed with DO1 but i had the same issue and tried to flash with OH6 but failed with odin.......i think my problem was that when i flashed with OJ7 i didn't turn frp lock....i didn't know i had to turn it off

guy i just got the bootloder and the modem files for OI1 , when do i flash them ? do i do it before or after the AP flash on the odin

http://forum.xda-developers.com/showthread.php?p=62626134
Maybe research this method. Sounds similar to what you got. What happens when you flash full DO1?
Anyone else got ideas?

tyrone1 said:
http://forum.xda-developers.com/showthread.php?p=62626134
Maybe research this method. Sounds similar to what you got. What happens when you flash full DO1?
Anyone else got ideas?
Click to expand...
Click to collapse
thanks i'll look into it and when i flash with DO1 it flashes but the same problem is still there
there are three 5.1.1 firmware and the latest two flashes with odin but the oldest one which is the OH6 fails when i try to flash it with odin

Once you are on DO1 you can't flash back to OH6. Was your phone originally on DO1? Or an older firmware?

tyrone1 said:
Once you are on DO1 you can't flash back to OH6. Was your phone originally on DO1? Or an older firmware?
Click to expand...
Click to collapse
i bought this phone online and the seller also doesn't know what the original firmware was... and yes i can only flash DOJ7 and DOI1 , the DOH6 flash always fails..... still the same problem though with both flashes.....after i flash i wipe factory and cache from recovery but the phone is still stuck on the initial samsung logo..... i think my main problem is that i flashed without turning off the FRP and TWRP flash is block by FRP lock

Maybe someone can suggest a solution or take to Samsung repair shop in your country

Samsung Note 8 N950F Boot Loop after latest update

Hey
After the latest update, every time I called with the Note 8, it would restart and every time I would switch it off, it would start back on. So the first thing I did was boot to recovery mode and wipe cache partition. When I restarted the phone, I would get a "No command" error and it would always boot to the recovery mode. Next, I tried flashing the latest firmware (I made sure to use the right carrier, VDH) from SamMobile using Odin which still didn't work. Then I tried NAND erase and re-partition and this didn't work either.
I am very new to this so any solutions would be greatly appreciated
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

NoteEight said:
Hey
After the latest update, every time I called with the Note 8, it would restart and every time I would switch it off, it would start back on. So the first thing I did was boot to recovery mode and wipe cache partition. When I restarted the phone, I would get a "No command" error and it would always boot to the recovery mode. Next, I tried flashing the latest firmware (I made sure to use the right carrier, VDH) from SamMobile using Odin which still didn't work. Then I tried NAND erase and re-partition and this didn't work either.
I am very new to this so any solutions would be greatly appreciated
View attachment 5256493View attachment 5256495
Click to expand...
Click to collapse
NoteEight said:
Hey
After the latest update, every time I called with the Note 8, it would restart and every time I would switch it off, it would start back on. So the first thing I did was boot to recovery mode and wipe cache partition. When I restarted the phone, I would get a "No command" error and it would always boot to the recovery mode. Next, I tried flashing the latest firmware (I made sure to use the right carrier, VDH) from SamMobile using Odin which still didn't work. Then I tried NAND erase and re-partition and this didn't work either.
I am very new to this so any solutions would be greatly appreciated
View attachment 5256493View attachment 5256495
Click to expand...
Click to collapse
When you tried to flash stock with Odin did it pass? Fail? Did it give an error code? Did you download the latest filmware? As you can't flash older filmware than what is already on the phone.

stonedpsycho said:
When you tried to flash stock with Odin did it pass? Fail? Did it give an error code? Did you download the latest filmware? As you can't flash older filmware than what is already on the phone.
Click to expand...
Click to collapse
Hey, thanks for the reply
When I flashed with stock firmware, Odin said it passed. And I used the latest firmware for my carrier from SamMobile

NoteEight said:
Hey, thanks for the reply
When I flashed with stock firmware, Odin said it passed. And I used the latest firmware for my carrier from SamMobile
Click to expand...
Click to collapse
I was hoping that it was an issue with Odin so I could possibly help you, even having a look on the internet doesn't being much help other than trying a factory reset. I've been on xda for years and never seen this issue before. Hopefully someone more knowledgeable will see your post, I suggest bumping your thread every 24 hrs.
Having tried flashing stock with Odin which usually resolves most bugs I would guess that it is a hardware issue and if you're able to, take it to a service centre.
If you do find a solution please post it here on XDA for anyone who searches this in the future

stonedpsycho said:
I was hoping that it was an issue with Odin so I could possibly help you, even having a look on the internet doesn't being much help other than trying a factory reset. I've been on xda for years and never seen this issue before. Hopefully someone more knowledgeable will see your post, I suggest bumping your thread every 24 hrs.
Having tried flashing stock with Odin which usually resolves most bugs I would guess that it is a hardware issue and if you're able to, take it to a service centre.
If you do find a solution please post it here on XDA for anyone who searches this in the future
Click to expand...
Click to collapse
Thanks for trying. If I do find the solution, I'll be sure to post it here

Looks like the partition in your internal SSD has been corrupted and needs to be reformatted. If that doesn't work then you need to have the motherboard on your device replaced.

iceepyon said:
Looks like the partition in your internal SSD has been corrupted and needs to be reformatted. If that doesn't work then you need to have the motherboard on your device replaced.
Click to expand...
Click to collapse
How would I go about doing this?

Bump

The same thing happened to me. I tried everything possible. I tried a new flash via odin. unsuccessful. only Download mode works, nothing else works, not even recovery mode, black screen.

Have anyone found the solution to fix this issue ?

im having similar problems