last year i recommended a colleague to buy this phone (mi a2 lite)
A few days ago, he told me that his son dropped him on the ground and broke the screen. he went to a shop and was asked for € 75.
later, he went to youtube and noticed that it's not that difficult to change it yourself. I searched the screen on the various e-commerce sites and found many. He would like me to help him buy a decent one so that he then undertakes to assemble it himself.
Do you have any to recommend? there are a lot of them and I wouldn't want to waste too much money. He said he needs the screen and any glue needed to attach it.
Many thanks in advance : Highfive:
(I translated everything with google translate to avoid too many grammatical errors ...)
I recommend watching the video in this link to disassemble. Also, Google for other A2 Lite tear-downs to get a good feeling for what you are going to do. As far as which screen to buy, I don't know which is the best but I bought this one. I am happy with it. The only other recommendation I have is to buy the screen AND the frame. It's only a couple more bucks for the frame. Then you just transfer the motherboard, etc... to the new frame/screen. No need to glue anything back and no need to worry about heating up the old screen to remove it.
A couple pointers:
* Be careful removing the fingerprint ribbon cable - it can rip easily (but a replacement can be purchased as well from China).
* Be careful removing the earpiece. I pried it up wrong and it split in half. I had to buy another from the UK which took about 3 weeks to arrive.
*When removing the tape that holds the battery in place, wind it slowly but firmly. If you go fast it will snap and then the battery will be hard to pry out.
Overall, I didn't think it was too difficult. I just had a problem with the earpiece & battery tape. Not bad considering I don't do this everyday.
Good luck!
Thanks a lot for the answer!
I watched the video and read the answers in that other thread too.
As soon as I catch my colleague, I will tell him all these things. I must also remind him that the phone has this middle name (redmi 6pro) so that he can get better information.
A little thing I didn't understand is that he told me he had seen a video showing how the screen was changed. And he told me how it has to be heated for a few seconds in order to detach it. Instead, in the video link in that other thread, it shows how to detach all the components until you get them all on the table. But, the only piece that had to "warm up" is the fingerprint reader.
Clearly, you suggested that I watch other videos on google and since this colleague of mine is not very well versed in the internet and the various ways to "retrieve information" I will have to help him both in recovering instructions and then ... ordering the necessary "pieces".
He told me that in addition to detaching the screen, after heating it ... there was only need to detach a cable or two that connects the screen to the motherboard and the game was done.
There is a thin thread that binds my future skill in recovering assembly and disassembly instructions ... the cost of the components and hoping that he has grasped the concept.
(I hope google translator has translated everything in a decent way xD )
If you follow my advice and replace the screen & frame, you won't need to heat anything to replace it. You just transfer the contents (motherboard, earpiece, etc...) from the cracked screen/frame to the new screen/frame.
The fingerprint reader attaches to the back cover and that gets replaced onto the new screen/frame...so it never has to be removed in the first place.
I found what I did was the best method for me. I tried replacing a screen on a Samsung Galaxy S4 years ago. Heating up the screen wasn't easy since I only had a blow dryer. I ultimately completely destroyed that phone trying to heat/pry the broken screen off, even though the video made it seem very easy. I didn't want a repeat of that so I choose to just transfer the components to the new screen/frame.
this is the video
https://www.youtube.com/watch?v=zNuRf7uOADc&t=437s
I finally found my colleague and told him about this other method.
I showed him (from my phone) the video posted in the other thread.
His response was:
"oh my god how do I put it all back together?
I would be confusing for sure. In the video that I have seen, just heat the front part and then I will only have to detach and reattach only 2 cables. "
he told me that he doesn't have that tool that looks like a hairdryer. But he would like to use a kind of hot metal counter that is used to pack the products in plastic. He would like to put the phone down a few seconds and then take off the screen.
I, if I had been in his place, I would have certainly opted to disassemble and reassemble everything. I do not trust very much to unstick and glue such delicate components.
But I've never tried either, so I have no idea how to make him understand that it's not as easy as it seems.
Assuming, that I have to buy him a screen that allows him to do as he says, which one should I buy? In the sense, I noticed for sale the famous screens with or without frames. But in your case, which one should I opt for?
I hate the fact that I have to take on this big responsibility of having to help and choose what to do.
however this forum is beautiful. As soon as I can I would like to follow him more to read the various topics ...
thank you for the advice not to heat the screen but to follow that method of detaching and reattaching the components but I may not be able to convince him ...
Reassembling the phone is no more difficult than disassembling it. In fact, it might even be easier.
Who is going to do the actual work? You or him? If it's him, let him do whatever he wants...his way. If it's you, then just get the screen & frame and swap components over.
The rest is up to you guys now. He asked you for help/advice. Tell him to let you help/give him advice or he's on his own.
Related
I'm assuming I smashed my At&t tilt or something, there is no cracks on the screen or anything, but the pic below shows the display I get. I'll have the phone for about a year in about 2 weeks. Anyone have an idea as to how much At&t or HTC will charge to fix this or am I better off buying a new phone? Or any ideas as to what could be broken and how it can be fixed? It doesn't allow me to do a hard reset. Thanks
well i don't know if warranty will cover it or not but you are still under your one year warranty so you could try to get a replacement. Its hard to say what could be causing it. You can check out mike channon's articles on disassembling a kaiser.
Good luck.
brianlb said:
I'm assuming I smashed my At&t tilt or something, there is no cracks on the screen or anything, but the pic below shows the display I get. I'll have the phone for about a year in about 2 weeks. Anyone have an idea as to how much At&t or HTC will charge to fix this or am I better off buying a new phone? Or any ideas as to what could be broken and how it can be fixed? It doesn't allow me to do a hard reset. Thanks
Click to expand...
Click to collapse
Well to my trained eye, it looks as though you have actually cracked the lcd screen. This damage isnt generally covered by any manufacturers standard warranty. Unless you purchased an extra warranty including accidental damage, I think its up to you to repair yourself unless you want to spend 400USD + for the repair. Taking it apart isnt terribly difficult and I have seen links to lcd screens posted all over for no more than 100USD. Check Ebay also.
http://cgi.ebay.com/LCD-Replacemet-...39:1|66:2|65:12|240:1318&_trksid=p3286.c0.m14
Here is one for 45 USD
Hope this helps ya
pyraxiate said:
Well to my trained eye, it looks as though you have actually cracked the lcd screen. This damage isnt generally covered by any manufacturers standard warranty. Unless you purchased an extra warranty including accidental damage, I think its up to you to repair yourself unless you want to spend 400USD + for the repair. Taking it apart isnt terribly difficult and I have seen links to lcd screens posted all over for no more than 100USD. Check Ebay also.
http://cgi.ebay.com/LCD-Replacemet-...39:1|66:2|65:12|240:1318&_trksid=p3286.c0.m14
Here is one for 45 USD
Hope this helps ya
Click to expand...
Click to collapse
I don't see a crack in the screen. Can there still be a crack in it that isn't visible or not noticeable until you take it apart? If that's the case I'll either buy a new screen or just buy a new phone on ebay for 200bux. Also anyone have any recommended sites on how to replace the screen?
This raises a great question for me. i work in a clean room/static sensative environment and repair and calibrate many different types of electronics (mostly signal generators & spectrum analyzers). I was wondering if anyone here has actually attempted to replace a LCD screen with success. And if so, how complicated the process was. I have downloaded the schematical drawings and have found replacement parts for the kaiser online for extremely cheap. i will post the site as soon as i find it again.
I did a screen replacement on a Wizard, and it wasn't that difficult. just make sure you don't break anything while trying to pry small pieces off to get to the screen.
Stu_Can_Sam said:
This raises a great question for me. i work in a clean room/static sensative environment and repair and calibrate many different types of electronics (mostly signal generators & spectrum analyzers). I was wondering if anyone here has actually attempted to replace a LCD screen with success. And if so, how complicated the process was. I have downloaded the schematical drawings and have found replacement parts for the kaiser online for extremely cheap. i will post the site as soon as i find it again.
Click to expand...
Click to collapse
ITs easy as hell.
I've done it two times with success.
Its only matter of two connection belts and thats all at all .
Screen replacement is really easy here.
brianlb said:
I don't see a crack in the screen. Can there still be a crack in it that isn't visible or not noticeable until you take it apart? If that's the case I'll either buy a new screen or just buy a new phone on ebay for 200bux. Also anyone have any recommended sites on how to replace the screen?
Click to expand...
Click to collapse
Generally you will NOT see a physical crack on the surface. The surface is actually JUST a digitizer ( a separate piece which is built into or ontop of your LCD for input purposes ). The digitizer is basically your touch screen portion of the LCD. What is actually cracked is the thin film below that which contains all of the liquid crystals.
As far as the replacement goes, I believe it is Michael Channon who has the step by step instructions on how to disassemble and replace the LCD. It isnt a hard task from what I can tell. I had taken my hermes ( Tytan ) apart so many times that i could do it in my sleep. Its not a terribly difficult process.
Here is Michaels Guide
Its not in English but its not hard to follow the pictures. He has done a great job at documenting the procedure.
If you are a bit scared to try it yourself, have a geeky friend do it for you ( maybe get him a date to a movie or something lol )
It should only cost you no more than 50$USD to repair ( Minus the bribe for a date lol )
Hope this helps you out !
pyraxiate said:
Generally you will NOT see a physical crack on the surface. The surface is actually JUST a digitizer ( a separate piece which is built into or ontop of your LCD for input purposes ). The digitizer is basically your touch screen portion of the LCD. What is actually cracked is the thin film below that which contains all of the liquid crystals.
As far as the replacement goes, I believe it is Michael Channon who has the step by step instructions on how to disassemble and replace the LCD. It isnt a hard task from what I can tell. I had taken my hermes ( Tytan ) apart so many times that i could do it in my sleep. Its not a terribly difficult process.
Here is Michaels Guide
Its not in English but its not hard to follow the pictures. He has done a great job at documenting the procedure.
If you are a bit scared to try it yourself, have a geeky friend do it for you ( maybe get him a date to a movie or something lol )
It should only cost you no more than 50$USD to repair ( Minus the bribe for a date lol )
Hope this helps you out !
Click to expand...
Click to collapse
Thx, I'm gonna give it a shot. I went ahead and bought the screen off ebay from the post by pyraxiate. Worst case I mess it up and buy a new phone of ebay for 150-200, which is what I originally thought I'd have to do, so this at least gives me a chance to save some $$$
brianlb said:
Thx, I'm gonna give it a shot. I went ahead and bought the screen off ebay from the post by pyraxiate. Worst case I mess it up and buy a new phone of ebay for 150-200, which is what I originally thought I'd have to do, so this at least gives me a chance to save some $$$
Click to expand...
Click to collapse
Let us know how it goes
Glad I could help
Got it all done, actually my pops did it. Works great, he took it apart just like the Mike Channon pics show, don't know if you had to do all of it or not just to replace the screen, but he did. Only one little annoying thing now that it's back together is that a small part of the black plastic out case hangs out just a tab and isn't flush, which makes it a little annoying when hitting the power/standby button on the right side of the phone. But I can learn to live with that I think. thanks for all the help.
congratulations!
good to hear you've achieved a successful repair!
correct me if i'm wrong...are you saying that the two halves of the phone (screen and keyboard) don't align properly when the keyboard is closed? if so, i remember a thread in this section of the kaiser forums that details (with pictures) how to possibly fix that particular problem!!!
"search and ye shall foundeth it !!!"
brianlb said:
Got it all done, actually my pops did it. Works great, he took it apart just like the Mike Channon pics show, don't know if you had to do all of it or not just to replace the screen, but he did. Only one little annoying thing now that it's back together is that a small part of the black plastic out case hangs out just a tab and isn't flush, which makes it a little annoying when hitting the power/standby button on the right side of the phone. But I can learn to live with that I think. thanks for all the help.
Click to expand...
Click to collapse
Im glad i could help Im also glad to hear the phone is up and running again
As was stated before, there is a thread for the case not aligning. I did some quick looking but to no avail. If i come across it ill be sure to post it
I'm not sure if I'm explaining it correctly. But it's basically the outer case, and around the power button it's not flush. Not sure if you can tell from my pics. I tried also doing a search w/no luck. I'm sure there is some specific name or something other than case that it's under.
When i replaced my faceplate i had the same problem. all i did was push it in...kinda hard, and it poped in, or you could use a plasic flathead and pop it back in...
DemoShadow said:
When i replaced my faceplate i had the same problem. all i did was push it in...kinda hard, and it poped in, or you could use a plasic flathead and pop it back in...
Click to expand...
Click to collapse
I tried that, and it doesn't seem to pop in at all.
I think its just like DemoShadow said. I dropped mine once and it seems to be a similar issue. I also just pushed really hard to get it to pop back in. I think its just that clip isnt in place as it should be when it was put back together. If anything, try to take it apart and put it back together
kristoff_sz said:
ITs easy as hell.
I've done it two times with success.
Its only matter of two connection belts and thats all at all .
Screen replacement is really easy here.
Click to expand...
Click to collapse
how did you put the keyboard back on????????????????
Can you be more specific?
Hey,
I literally just replaced the screen on my backup Tilt last night. Still got most of it in my head.
What, exactly, do you mean about putting the keyboard back on? Got any pics of where you are now?
This was one of the easiest things I've had to do...asside from it being somewhat tedious. Most of my issues were resolved by MAGNIFICATION! Once I could see what I was doing, there were almost no issues.
I only paid $31.99 on eBay for a screen with free shipping (from USA no less)...less than the $35 I would have had to pay with the insurance through my Provider Dealer...and I didn't have to wait for 3-5 weeks to get it back.
I'd do this for people with broken screens as a service, but I can't guarantee the cost of the screen...it goes up and down too much.
If you can be real descriptive, or have pictures, I'm pretty sure I can help get you back together.
Let me know, I'll keep an eye on this thread...
RAF
here's some dismantling guides
http://www.mikechannon.net/page1.html
you dont have to remove the keyboard to replace the LCD, unless u're talking about the outer keypad, which just sits in its spot
is this housing http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260453968402&ssPageName=ADME:X:RTQ:US:1123 a FURTHER rip-off in quality as the OEM found here http://cgi.ebay.com/OEM-SONY-ERICSS...ries?hash=item2ea6dd8d1e&_trksid=p3286.c0.m14
i want to buy a new housing but i don't wanna buy one with less quality than the original
what are your thoughts on the pics there?
Judging by the pics both fascias seem identical. Although don't know why this big pricing difference. Maybe the first auction is for a replica housing? Don't have large pics as the second auction so we can tell for sure.
Also, at CNN http://cnn.cn/shop/sonyericsson-xperia-c-28_638.html the housings are pricey. For me go for the second auction or buy from CNN, you will be 100% sure that the housing is the OEM.
yeah i was looking at the $24.00 on ebay too... someone should buy it and tell me how it is
i think im gonna let this pass and sell my x1 as it is, im thinking of leaning towards the touch diamond 2 i will miss my keyboard but what the heck
Yo!
I ordered the $24.00 last week... When I receive the housing parts, I will take pictures and spread the message....
Fingers crossed......
Damn the cracks....Its a pity to sacrifice a gd device just now that some gd new things are coming....senseUI....Leo...sure it'll come for d2 too.....but no KeyBoard there.....I have ur very same problem...but I'll try the case !!
Received the housings yesterday.
They're certainly not OEM (maybe the backcover is, the rest not). The outside looks quite nice finished, the set is quite complete (with some tools for the fitting). From the two sets I ordered, one has a large gluestain on the top part of the housing (below the LCD). This gluestain damaged the paint. So I decided to start transferring the phone in the other housing.
After dissecting the phone I started with the assembly of the screen part. The speaker fitted not quite nice, so took some feddling to get mounted. At last it fitted (the print on top of the speaker fitted just). Closing the top part of the housing was a mess. The snap-locks didn't snap (partly) and on one side the housing did not flush fit. The (original) screws did not fit in the thread bushings.... With some fiddling I sort of managed to fit them. Then on with the bottom part. The new chrome buttons do not fit in the new chrome housing part.......
This is were I give up for yesterday. I think I'm going to rebuild the old housing en give up on the new one....
So.....
Decide for yourself if it's worth the trouble.... The housing looks quit neat (not as good as OEM though) but the fitment process is quite troublesome. Delivery was fast and the package is complete (including self-adhesive rubber for screen and speaker fitment). I will get in touch with the guy from Ebay with my findings.... Maybe I'm doing something wrong....
Will post some pictures tomorrow or something....
thnx ur comments were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx, ur comment were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx dude, im waiting on mine to be delivered,
looking forward for more reactions...
@Fliptil
From a scale from 0-10, how hard was it to do?
Before starting myself, I want to know if i'm capable of doing this.
To be honest, I know how to fix stuff, but don't know if I can do this trick..
Thanks for sharing anyway
Does anybody know, where i can buy a non branded battery cover for my sliver x1?
It is branded with T-Mobile, but i would like to have it blank or non-branded.
An original one is 25 € in ebay Germany. That's too much. So a cheap one would be fine.
Thanks in advice for all tips!
Best regards
Jog
ebay dude, i purchased one 2 weeks ago for about 10 GBP
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=170363212269
OK guys....
I managed to revive the Xperia tonight.... It has become a hybrid with the metal (original) front and black backside. The middle part is also left original. So the only part I ended up exchanging has been the back cover.
First of all; kudo's to HTC for making the Xperia somewhat sturdy (at least the inside is...). The amount of mechanical havoc tha has been put through the innards of the phone are substantial... And still everything functions!!
After the initial assembly attempt a few weeks ago, I was sure that I had wrecked my phone trying to assemble it with the new housing. Some parts did not fit really well, and the (original) screws did not quite fit the (new) threaded bushings. Halfway through the assembly process I ran into the new chrome buttons not fitting in the new chrome middle part and I gave up on assembly for the time being. After recharging myself for a couple of weeks I forced myself to take up the task of finishing the assembly of the phone tonight...
First I had to disassemble the phone (I was halfway assembling it...) again. I decided to use the original front (had some scratch damage and a very small crack) to surpass the not-fitting thread bushings in the new part. This was a problem... One of the screws had settled in the not-fitting thread bushing and decided to not unscrew, but turn the bushing in the plastic instead. After trying careful and not damaging anything for some time I decided it was time for the hobby knife and screwdriver (as crowbar...). The new front cover did not survive this operation. The screw and the innards of the phone did however!! Reassembly using the old front cover was quite easy, as was reassembly of the back using the original middle part. In the new back part was the thread bushing missing for fixation of the speaker... I used the not-fitting bushing from the front cover as bushing for the speaker fixation. Off course after I made the bushing fitting by forcing the screw in the bushing using a sturdy screwdriver and a set of pliers. This bushing was hammered (carefully...) into the location where the bushing should have been.... This sort of worked. The new back cover does not fit as neat into the original middle part as the original back cover, but it did fit (with some force). The plastic lip that fixes the SIM card was a bit to long, so I had to cut of 0,5mm to make it fit the SIM card. And last but not least only one of the two new battery covers was able to get a grip on the phone...
Then came the thrilling moment to switch on the phone.... Everything worked as if nothing had happened!! So end good all good; I have a phone that looks quite neat (part brushed metal - part black) and functions.
If it was worth the hassle... I doubt it... When you've got a phone that is in pieces and you want spare parts to repair it (as cheap as possible and you like some hobbying) then go ahead and buy this housing. If you want a phone that looks as good as new (and you don't want to risk a heart attack or nervous break down) then I guess you're better off leaving this housing as it is.... For a phone that's worth a few hundred bucks I think this housing is not OK. For a scrapheap phone that needs revitalisation for a small amount of money than it's OK.... If I had to do it all again I think I would have gone for an OEM housing.... After all, I'm happy that my phone functions again so I can leave the TYTN at home. I was to stubborn to buy another housing...
This has become quite a story, hope it will be of any help to somebody. Now I must see if I can post some images....
Grreetz,
Ronald
Some pictures.... try if it works....
Hmm i've dropped my poor x1 on the concrete sidewalk as i got out of my car.
Amazingly it must be good quality because there are a only a couple of scratches on the front and some damage on the rubber around where the
stylus is, but otherwise everything works and is functional.
What this experience did, was got me lookin for spare parts in case I'd
ever need them. As a result I ordered from the same person on eBay 2 days ago
and I just now found this post. Needless to say, I'm damn scared that I've
wasted the money. You tried to fit the black parts on a silver X1, and mine is black,
so I'm crossing my fingers that for some unknown odd fantastical reason, it fits better on the black version. Also may ask whether your model is an x1i or x1a?
I'm guessing b/c its silver its an x1i but u can nvr be to sure. As for me, mine is
a black x1a. I'll post back if i have any updates.
Hi Nick.
I've got a X1i, as you had already guessed.... The mixing of the parts is also a bit of a risk.... The chrome middle part (original) has suffered some damages during my disassembly actions to start with... And has developed some new cracks in the use as a hybrid. Maybe I've overtightened some screws, or maybe the bottom part does not fit well enough so it develops to much tension I don't know...
I've decided to use the X1 till it dies, and to buy something else (no slide keyboard) a little bit more sturdy when it does. I am not going to do any repairwork on it. The design is simply flawed, I have had it repaired at SE once, when it came back it was broken again within two months. These stories can be found al over the internet, so I am not going to repair it again (just to get it broken again). I am not careful enough for a phone like this (however, my colleague also has a X1 that's broken and he is very careful...) I guess.
Just my two cents.
thanks fliptil I'll keep those things in mind.
Before i dropped my x1 for the first time. There was some kind of defect in the silver middle part. At first it was a slight crack so i thought nothing of it, until a piece fell right out of it. Until now i've never needed to go through the process
of getting something fixed and was my experience painful. I got mine through a carrier (Rogers) so I called them on the phone. I was on hold forever, and when I finally got through they told me I had to go to a rogers store to have someone
personally take a look at it.
I got to the store, got on their phone, and was on hold for 20 minutes. When I got through they told me they would connect me to a specific department.
Another 20 minute wait.
I got through and then gave the phone to a rogers employee there. He confirmed that it should be a defect as there were no signs of dropping it and then HE waited 20 minutes while the guy on the line called sony.
I waited all that time to find out that I cannot get it replaced through my carrier but had to go through sony themselves.
I looked up some stories of experiences with SE's services and found that most (if not all) of the time they replace your x1 with a refurbished one, and I wasn't about to trade a perfectly brand new one with a minor ding in it, for
one that could be potentially scratched up and badly treated.
Now that I've dropped it though I fear that whether the defect gets worse or not I cannot get Sony's warranty on it. However, after what you've just told me I don't think I want to. Here's to hoping that i won't have to do x1
surgery anytime soon...
I am the proud owner of a new I9000, the b*&tard love child of 2 ebay purchases. Just wondering whether the leftover entrails are worth keeping. Specifically:
- broken USB port. I have a replacement part and looks easy enough to de/solder. Anyone tried??
- vol down button. Looks a nightmare to try to replace. Anyone tried??
- chip in screen. Not worried about it being perfect but its too deep to polish out and when you put a screen protector on it a bubble appears. Any ideas?
- chrome bezel. WOWOW didn't Samsung make it a separate element easy to replace...?? Has anyone done these successfully (first time, every time), or is there any way to make it look good? Other than hiding with a case which I have already done!
Thank you for all, any, or even no help.
H.
ihartley said:
Thank you for all, any, or even no help.
H.
Click to expand...
Click to collapse
look at manuals and guides in My Android collections for your answers
If you're handy with a soldering iron and have a good one (not one of those fire-starting ones that plugs straight into the wall with a handle like five inches away from the tip) then the micro USB and button shouldn't be too tricky to replace. The button isn't that terribly important anyway depending on how you use your phone.
As far as the screen chip, I'd be tempted to use one of the screen protector methods using alcohol, perhaps the alcohol would fill the gap and stay there? Probably wouldn't work, but it might be worth a try.
I replaced the chrome bezel with a cheap, crappy gold one from china (and a gold battery cover) and it's totally pimp. The bezel is actually the very last piece in the phone though. You have to take EVERYTHING apart to get it out, it's a huge pain. I ended up slipping with a knife while I was doing it and cutting the vibrator off so I spent a few weeks waiting for the replacement touch button/vibrator/microphone board to come in.
Hi, I recently got my HTC One (m7 / at&t) as a graduation present in June. Unfortunately I recently dropped it face down without its case onto the ground and resulted in a large crack(s) on the screen. I can still use the device, text, talk, watch videos etc.. but as you can obviously tell one does not simply enjoy the pleasure of having their phone(s) screen cracked.
So I immediately began looking for a solution and repair shops said 300$ to fix when I purchased my phone for just a little over 300$. So that is out of the question, unless its truely my last resort. So I began looking on how to fix it, youtube failed me the only thing that was helpful were the breakdown videos of the HTC One teaching me how to take apart the phone (The only part I was interested in was on taking out the glass).
The only solution I currently can think of would to repair it myself. So here are my questions.
1) The screen is cracked only, the touch screen works fine etc.. so can someone show me the listing on ebay/amazing (I prefer amazon) of the kit or things I would need to fix it.
I Saw this one:
amazon /HTC-M7-screen-digitizer-replacement/dp/B00CWKGZ5U/ref=sr_1_5?ie=UTF8&qid=1376517625&sr=8-5&keywords=HTC+One+Glass
Because it looks like exactly what I Need, BUT I'm no expert so would that fix my problem? Or is it the wrong thing since all I need is the glass and thats the "Digitizer Outter Glass" or something? I dont know my terms that well but to me it seems like what I need because its the "Outter Glass" haha.
But I'm confused about that because it says Digitizer outter glass and in the picture has the connection cord thing, Would this be replacing every part having to deal with the screen? (i.e I take a suction cup and take out the screen, and unplug the connection from the phone to the screen, would what I having in my phone (cracked screen with cord..) be the same thing as what Ill be ordering from that amazon thing but NOT cracked?)
-----------
2) How would I replace it step by step? I already seen videos of taking the phone apart and replacing iPhone screens but I havent seen any towards the HTC One in regards to replacing the screen. So would someone mind pointing me in the right direction, or giving me a text tutorial on what to do? I can pretty much figure it out by reading it since I have videos n pictures to compare it to sorta.
-----------
3) I never done a repair before but it doesnt seem that hard, just have to be gentle and know what youre doing (Thus why im asking so many questions), is this my best option? Or what should I do...
-----------
4) When I seen videos regarding the iPhone screen replacement it was showing things like Screen Seal / and him literally taking off the glass from the this other thing and replacing just the glass itself instead of the thing below it.
Would I have to also use a type of screen seal / or have to take glass off like you would do in the iPhone or is it a 100% different conecpt / idea?
----------
Remember: I basically need to know what I need to fix the cracked screen of my phone, I think this is what i need:
amazon /HTC-M7-screen-digitizer-replacement/dp/B00CWKGZ5U/ref=sr_1_5?ie=UTF8&qid=1376517625&sr=8-5&keywords=HTC+One+Glass
So if it is, then may someone tell me how to replace my phones cracked screen using that and explain it to me what im actually doing and watch each part is etc.. (like what im buying and whats cracked with my phone, so I know its what I need)
and if not, can someone tell me what I need and how to do it?
PS I understand I cant post outside links, but its amazon and Im not trying to advertise i just need the link as a comparison / example
This is one of the worst phones created when it comes to repair. It is well made, but ease of repair was not their priority. The only thing I can recommend to you would be to go to the Ifixit web site. They do a tear down of the phone to show how hard it is to repair. Maybe that will help you out.
Edit: In your original post, you wrote that you had watched videos on the Iphone. Since this is a different phone with differences in assembly, I suggested a video concerning this specific phone. Not trying to be rude, but if I was taking apart my HTC, I would view specific videos concerning my phone. I thought that the specific video might give you clues as to the parts involved in assembly and what procedures were necessary. The video I was referring to concerned their taking apart an HTC One. Every bit of information might be helpful to you trying to fix your problem.
Wolf said:
This is one of the worst phones created when it comes to repair. It is well made, but ease of repair was not their priority. The only thing I can recommend to you would be to go to the Ifixit web site. They do a tear down of the phone to show how hard it is to repair. Maybe that will help you out.
Click to expand...
Click to collapse
Not being rude but I'm pretty sure I already stated the fact that I seen the videos and tutorials regarding the tear down of the phone. So how do you expect that to "maybe" help me out? If I'm trying ti find out the part(s) I need to replace since I don't know the full termology.
I know how to take my phone apart (For the most part), I Just need to know mainly what I need to replace to fix my cracked screen, or whats my best solution. + The questions i stated in the thread.
Thank you.
Unfortunately you will have to change the whole screen assembly.
This will cost you a little ... http://www.etradesupply.com/oem-htc...itizer-assembly-with-front-housing-white.html
You could try also just the LCD+ digitizer (if the front aluminum parts are still intact: http://www.etradesupply.com/oem-htc-one-lcd-screen-and-digitizer-assembly.html
If you scratched the back of the phone, those guys have the back assembly also ... about 24 USD ... ( http://www.etradesupply.com/oem-htc-one-rear-housing.html )
You could TRY replacing only the digitizer ( http://www.etradesupply.com/oem-htc-one-digitizer-touch-screen.html ) but I would not go there. In between the digitizer (what is actually cracked in your case) and the lcd there is a special "jelly" glue which is VERY hard to remove w/o breaking the LCD. I tried that on a N7 and now I'm waiting for a new LCD to be delivered ...
Good luck!
Thank you, I appreciate the reply.
My casing / housing isnt broken (The cracks start from the top of the screen right below the camera/speakers where the glass is, and the crack(s) end towards the HTC Logo etc..) so should I still buy the white housing with lcd+digitizer or should I just go with the second option and buy the digitizer+lcd without the housing (second link you gave me)
JohnVerde said:
Thank you, I appreciate the reply.
My casing / housing isnt broken (The cracks start from the top of the screen right below the camera/speakers where the glass is, and the crack(s) end towards the HTC Logo etc..) so should I still buy the white housing with lcd+digitizer or should I just go with the second option and buy the digitizer+lcd without the housing (second link you gave me)
Click to expand...
Click to collapse
Let us know how it went. :good:
Not sure if it's worth it. HTC will fix it for you somewhere around $180.
Sent from my HTC One using xda app-developers app
JohnVerde said:
Hi, I recently got my HTC One (m7 / at&t) as a graduation present in June. Unfortunately I recently dropped it face down without its case onto the ground and resulted in a large crack(s) on the screen. I can still use the device, text, talk, watch videos etc.. but as you can obviously tell one does not simply enjoy the pleasure of having their phone(s) screen cracked.
Click to expand...
Click to collapse
Hi,
I posted a lengthy thread on how to do a repair here
http://forum.xda-developers.com/showthread.php?t=2387992
Did it well over a month ago and it is still running fine.
You might want to call you household insurance, and tell them someone in your household (not you) dropped the phone while cleaning for example.
Here in the Netherlands, they will pay the repair even the same day.
I didn't had to send them anything, just tell them on the phone how much the reparations would cost, and they transfered the complete numeber right away!
Too bad I found that out after spending more than $100,- on phone reparations.
It might be worth the shot, since they may reimburse it for you.
This morning I was cleaning my phone (getting rid of the finger prints/smudges) while standing up when it slipped out of my hand and hit the tiled floor. Everything is fine except the screen (which is cracked). Screen works fine but is unresponsive no matter where I press or touch the screen. How much does a Z3 Compact replacement screen cost? I searched around and it seems it is about $100?
Screen replacement costs in Poland +/- 135$
(authorised sony service)
Yes' it's hard to get original one cheaper than 100-120$. You can search for some Chinese replacement cause sometimes it looks quite similar to original one but You must check it before buying. Last time I had a client with Z1c replacement screen which he bought for 40$ and there was no white color, everything what should be white was purple.
Voids warranty, cheap replacement
Got mine from here replacebase dot co dot uk (can not post links ), of course you void your warranty if you do it yourself.
Parts are good quality till now. I advice to order a back glass too, I broke mine when taking it out and had to reorder again (costs approx 6 pound).
Next time just heat up back glass with hair dryer and You wont break it.
Chamelleon said:
Next time just heat up back glass with hair dryer and You wont break it.
Click to expand...
Click to collapse
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Thanks for the replies.
I'll be getting the repair done from the official Sony shop/distributor I bought the phone from. Just wanted to get an idea of how much it "should" cost before I approach them.
m4mbax said:
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Click to expand...
Click to collapse
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Foxhunter123 said:
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Click to expand...
Click to collapse
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
m4mbax said:
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
Click to expand...
Click to collapse
Doh!!! ? I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) ?.
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Most pre-glued adhesive stickers on back are useless. Now everytime I change back in Xperia Z, Z1, Z2, Z3 and compacts I need to remove pre-glued sticker and change it to original one. Many times I had complaint on it from my clients saying that back glass came off. So it's better to order original back glass or just original adhesive.
Foxhunter123 said:
Doh!!! I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) .
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Click to expand...
Click to collapse
Good
Mine came with the adhesive ON the screen, I used that one, I didn't have a separate one. Be extra careful when 'placing' the adhesive where it belongs because you can not remove it once place (okay maybe slightly). Its important that it fits on the first to first and a half try. More adhesive means thicker layer --> glass will stick out
Anyway, most of the stories you read online are partially BS, the phone will work even when the glass is a tiny bit loose or when the adhesive rotated and is a bit thicker in one place. In my eyes, when you dared to order, you are very much capable of assemble the parts.
In btw, ordered new glasses today, hope my two left hands fix it this time.
PS: A lesson I learned on a friends Galaxy S2, do NEVER EVER try to use force when something sticks or is not as loose as in a video. Google or ask another person maybe you just dont do the trick. A connector didnt want to come off so we used a lever to lift it, CLICK, the place where the lever levered broke the board... :silly:
Edit 1: I think its not necessary to HEAT it, it just has to be a lil bit warmer than in your pocket or when calculating heavily. 30s under a hairdryer will be more than enough i guess.
Forgot to update this thread. I received my fixed phone last week. They replaced the screen and even the "bumpers" around the phone for $98. They even delivered the phone to my home free of charge. Looks brand new, all the minor dings I had on the phone are gone.
On another note, I also bought my first iPhone. Got an Space Gray iPhone 6s 128 GB with the official/Apple leather case for the 6s. Got it last Thursday. Been playing around with it a lot and, overall, I love it. Deciding on whether to keep my Z3 Compact as a back-up phone or just sell it. But geez, does the iPhone 6s load games and other apps fast (thanks to its NVMe storage).