Database Develop

[Tutorial] KDZ can see your device? No Problem!

Ok so allot of people have been asking, if kdz can’t see my phone then how do I flash.
This is a simple yet effective solution that I have found.
This will work even if
• usb debugging is off
• You made a factory reset
• Device wont boot
Before I start I need to give thanks to @mircea89fzr for providing this tutorial
http://forum.xda-developers.com/showthread.php?t=2409308
Step 1
Head over to http://lg-phone-firmware.com/ and download a kdz image for your device
Step 2
Download LG_KDZ_FW-Update_OfflineFix.ZIP (attached) thanks to @mircea89fzr
Step 3
Run B2CAppSetup.exe inside the KDZ_FW_UPD_EN folder and make sure you install the drivers then close the program
(if you get program not responding undo changes you made in the next step and give it some time)
Step 4
Open notepad as Administrator(Go to windows menu, type notepad and right-click and run in Administrator mode)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 5
Open the hosts file (c:\windows\system32\drivers\etc)
And add this line 127.0.0.1 csmg.lgmobile.com
Then save and exit
Step 6
Go to windows menu, type cmd and right-click and run in Administrator mode.
Drag auto.vbs over command prompt and hit enter.
Step 7
Click OK until you get this
Step 8
Make sure Type is set to 3GQCT and phone mode to DIAG. Select your KDZ file and click Normal web upgrade test.
Step 9
Click on Upgrade Start.
Step 10
Click on Clear phone Software update Registry and then click OK.
Step 11
You upgrade will start and then give you this message
Step 12
Disconnect the usb cable
Remove your battery
Reinsert your battery
Plug in the cable
Power on
Then Click restart
Step 13
Your Device will be detected for a split second and the flash will continue.
If it gives you the pop up again repeat step 12
Step 14
Flash may get stuck at 4% of update
Repeat step 12
Step 15
Remove the line in the host file
Step 16
All done

slipsystem said:
All done
Click to expand...
Click to collapse
this is the copy of this http://forum.xda-developers.com/showthread.php?t=2409308 thread ???

AXD96 said:
this is the copy of this http://forum.xda-developers.com/showthread.php?t=2409308 thread ???
Click to expand...
Click to collapse
My apologies I should have made it more clear this is not a guide to flashing a kdz image as it was already discussed in this thread.
http://forum.xda-developers.com/showthread.php?t=2409308
this is a guide to flashing the kdz if your computer does not see your phone. It is more about step 11 on wards.
my apologies if I am offending the forum rules but I did give proper thanks and I have mentioned mircea89fzr so that he can see that I created this thread and message me if it is a problem.
the reason I posted this is because a lot of people have asked me how you flash when your device is not detected. referring them to this single post http://forum.xda-developers.com/showpost.php?p=45988501&postcount=23 does not help people as it does not explain how to get to that point. the user would then have to page back to find the tutorial. I made this guide so that they can see step by step in one post.
I will have no problem removing the post if mircea89fzr requests but I would make a suggestion to include steps 11 on wards as an addon to the original post.

slipsystem said:
My apologies I should have made it more clear this is not a guide to flashing a kdz image as it was already discussed in this thread.
http://forum.xda-developers.com/showthread.php?t=2409308
this is a guide to flashing the kdz if your computer does not see your phone. It is more about step 11 on wards.
my apologies if I am offending the forum rules but I did give proper thanks and I have mentioned mircea89fzr so that he can see that I created this thread and message me if it is a problem.
the reason I posted this is because a lot of people have asked me how you flash when your device is not detected. referring them to this single post http://forum.xda-developers.com/showpost.php?p=45988501&postcount=23 does not help people as it does not explain how to get to that point. the user would then have to page back to find the tutorial. I made this guide so that they can see step by step in one post.
I will have no problem removing the post if mircea89fzr requests but I would make a suggestion to include steps 11 on wards as an addon to the original post.
Click to expand...
Click to collapse
ok
it's only a question

I'm stuck at 4% i.e flasher is not detecting my phone, what to do?
P.S i'm using "download mode" from boot-up bcuz my phone is bricked already

[GUIDE] Fix No Network Signal Error in Mi Note/Pro

Hello Mi Note/Pro Users,
Today I'm here to solve the problem of No network signal error in your Mi Note/Pro by giving you a simple tutorial that you can do it yourself easily. Note: This tutorial can be used for both Mi Note/Pro.The steps are same, but make sure you use the correct file for your device.
For this tutorial we need some things, so let's get the things ready before starting the tutorial
We need Mi Flash Tool. So Download MIUI Rom Flashing Tool and install it in your computer.
Download the Modem file for your device: For Mi Note: Click here. For Mi Note Pro: Click here. The zip that you downloaded needs to be extracted to get the modem file. The modem file that you get after extracting the zip file would be named like this NON-HLOS.bin
Now let's get started.
Turn off your phone and enter your phone into fastboot mode. (For entering into fastboot mode, Press volume - and Power button together until you see the fastboot image on your phone.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After entering the phone into fastboot mode, Connect your phone to the computer.
Since you have installed MIUI Flashing tool, go the Android folder of the MIUI ROM Flashing tool, ie C:\Program Files (x86)\Xiaomi\MiPhone\Google\Android. MIUI ROM Flashing tool will be installed to the above location by default.
Copy and Paste the modem file (NON-HLOS.bin) to the folder mentioned in the above step. Some times your pc will ask to provide administrator permission to paste the modem file to the above mentioned folder like this:
Press continue and the file will be copied and pasted to the folder C:\Program Files (x86)\Xiaomi\MiPhone\Google\Android.
Hold down the left Shift key on your keyboard and right click inside this folder and then select Open command window here.
This will launch the command prompt screen like this.
Type the command fastboot flash modem NON-HLOS.bin and press the Enter key to flash the modem like the one in the screenshot below. The screenshot below is actually of the Redmi 2 phone, so for Mi Note/Pro it will be slightly different. The modem will be flashed successfully and type in fastboot reboot to reboot your phone.
Your network should be back after that. Enjoy.
Source
Special thanks to @Technoking2020 & @teejay456
The modem files for this tutorial of MI Note/Pro are extracted from the fastboot developer rom of the respective devices.

Just an FYI I tried this when trying to revert from 5.1 back to 5.0 and it didn't work. I had to do a fastboot flash of the entire rom file to get it working again

I have this problem when restoring TWRP backup. Still its enough to get out of trouble.

not files
Might rise again modem files not let me download or host any file , in advance thank you very much

drako11 said:
Might rise again modem files not let me download or host any file , in advance thank you very much
Click to expand...
Click to collapse
http://en.miui.com/thread-166934-1-1.html

can you re-upload the files?
I am having same issue and i really need the files.
Thank you!

please re-upload for Mi Note Pro
Thanks !

I have followed it for mi note pro, it doesnt help, imei is all fine, serial is all fine, installed fastboot roms different versions, tried different version modems, imei is not blacklisted, everything is fine, still no success, any advice will be appreciated ?

can u please reupload the file ,it cannot download ,thank

help is needed
Good afternoon! Friends, I need help urgently! After flashing the modem, Mi Note writes that there is no SIM card,
Friends who can make backup partitions workmodem1, modemst2, fsg, I will be very grateful to you.
And then I'm sitting now with a player in 64GB. The instruction is very simple, especially for those who installed it either through the "ADB" folder.
Instruction:
1). Switch off the phone. We are going to restore TWRP. We connect the cable to the computer.
2). We go in the folder adb. Press SHIFT and right-click anywhere in the folder. Click Open Command Window.
3). Write the following commands:
Adb shell
Su
Dd if = / dev / block / mmcblk0p12 of = / sdcard / modemst1
Dd if = / dev / block / mmcblk0p13 of = / sdcard / modemst2
Dd if = / dev / block / mmcblk0p16 of = / sdcard / fsg
All backups are ready.
Modemst1, modemst2, fsg files will appear in the phone's memory
If someone is worried about IMEI, then it is not copied in this backup, if not.
Friends, I hope for your help!

rshahzad17 said:
I have followed it for mi note pro, it doesnt help, imei is all fine, serial is all fine, installed fastboot roms different versions, tried different version modems, imei is not blacklisted, everything is fine, still no success, any advice will be appreciated ?
Click to expand...
Click to collapse
Have you solved it? I have the exact same problem as you..
---------- Post added at 12:23 AM ---------- Previous post was at 12:21 AM ----------
Didn't work for me.. I tried everything and stills no signal

mati69ase said:
Have you solved it? I have the exact same problem as you..
---------- Post added at 12:23 AM ---------- Previous post was at 12:21 AM ----------
Didn't work for me.. I tried everything and stills no signal
Click to expand...
Click to collapse
No it didn't work, I moved on to another phone, note pro was a disappointment.

Efs backup folder
Can someone send me the EFS folder?

mi note pro no signal issue
mati69ase said:
Have you solved it? I have the exact same problem as you..
---------- Post added at 12:23 AM ---------- Previous post was at 12:21 AM ----------
Didn't work for me.. I tried everything and stills no signal
Click to expand...
Click to collapse
has anyone been able to get this working again.

I have the same problem someone would have an idea.

modem file attchment
dear mr kahun,
plz help fot the link for modem mi note
im keep tryin to download but not succeed
thanks

And on MI3 ?
Dear,
does that work on MI3,too ?
If not,is there any solution you know about the same issue on MI3 ?
Thanks a lot

I have been flashed my mi note 2 with 2 different file which I get from Google unfortunately after flashing my phone is now blinking altime....please help me soon

I could not download that Download the Modem file for your device: For Mi Note: Click here. For Mi Note Pro: Click here. The zip that you downloaded needs to be extracted to get the modem file. The modem file that you get after extracting the zip file would be named like this NON-HLOS.bin
So please give to me that file download link again
thank with

How to backup/restore imei number [easy method without rooting]

First install latest asus drivers from here ASUS DRIVERS
install Qualcomm usb drivers from here Qualcomm DRIVERS
Download and install qpst flashing tool from here QPST TOOL
For Backuping qcn file
Go to cdrive>program files>Qualcomm>QPST>bin
open QPSTConfig and then start clinets>software download, and go to backup section then take a backup in qcn file format (take backup in diag mode as shown below)
For Restoring qcn file
1) Flash stock rom via fastboot (dont use custom recovery) and lock the mobile with pattern lock
2) now enable usb debugging and conect mobile to pc then type adb devices in minimal adb then give permission
3) Now click on emergency call in lock screen and type *#3424# now the device will be in diag mode
4) Now open QFIL (from cdrive>program files>Qualcomm>QPST>bin) then go to tools and click on QCN backup restore
5) Go to browse and add my qcn file QCN FILE then click on restore QCN
6) After restoring make a reboot and then again connect in diag mode (Repeat steps 2&3)
7) now open IMEI-Fix.exe IMEI-Fix.exe then in IMEI1 section type ur first sim IMEI number which u can find on ur box in IMEI2 section type ur second sim IMEI number
8) Then click on start it will flash ur original imei numbers then make a reboot that's it ur baseband problem is fixed
NOTE:-
1) I tried other qcn files but i faced 10% drop in 1hr in idle mode so use this qcn file for no issues
2)Don't forgot to change the imei numbers to ur original numbers by using imei-fix app otherwise u will face network issues
Credits :
Praveen Pannu for his easy guide to fix it
Adarsh For the QCN file backup

IMEi fix tool link is dead kindly update

abiidea said:
IMEi fix tool link is dead kindly update
Click to expand...
Click to collapse
now check

Ravuri yaswanth said:
First install latest asus drivers from here ASUS DRIVERS
install Qualcomm usb drivers from here Qualcomm DRIVERS
Download and install qpst flashing tool from here QPST TOOL
For Backuping qcn file
Go to cdrive>program files>Qualcomm>QPST>bin
open QPSTConfig and then start clinets>software download, and go to backup section then take a backup in qcn file format (take backup in diag mode as shown below)
For Restoring qcn file
1) Flash stock rom via fastboot (dont use custom recovery) and lock the mobile with pattern lock
2) now enable usb debugging and conect mobile to pc then type adb devices in minimal adb then give permission
3) Now click on emergency call in lock screen and type *#3424# now the device will be in diag mode
4) Now open QFIL (from cdrive>program files>Qualcomm>QPST>bin) then go to tools and click on QCN backup restore
5) Go to browse and add my qcn file QCN FILE then click on restore QCN
6) After restoring make a reboot and then again connect in diag mode (Repeat steps 2&3)
7) now open IMEI-Fix.exe IMEI-Fix.exe then in IMEI1 section type ur first sim IMEI number which u can find on ur box in IMEI2 section type ur second sim IMEI number
8) Then click on start it will flash ur original imei numbers then make a reboot that's it ur baseband problem is fixed
NOTE:-
1) I tried other qcn files but i faced 10% drop in 1hr in idle mode so use this qcn file for no issues
2)Don't forgot to change the imei numbers to ur original numbers by using imei-fix app otherwise u will face network issues
Credits :
Praveen Pannu for his easy guide to fix it
Adarsh For the QCN file backup
Click to expand...
Click to collapse
Thank you so much, it worked like a charm.
You just saved my device.
Also I suggest adding screenshots after every step will be awesome.
Thanks man, great work:good::good:

infinity.plus said:
Thank you so much, it worked like a charm.
You just saved my device.
Also I suggest adding screenshots after every step will be awesome.
Thanks man, great work:good::good:
Click to expand...
Click to collapse
Thanks bro

I'm getting device not connected error in QFIL. Pls help

<Mod edit>
Does your phone has warranty? If yes, the store that you buy your phone is where to go repair.
Remember don't install any magisk module like: Pixelarity, Oxy-ify, Pixify. Flash stock rom and lock the bootloader first if unlocked.
Sent from my ZenFone Max Pro M1 using XDA Labs

Hi
Yes but I do not live in US and does not worth because of high taxes. I tried what is in the thread and I could not find the IMEI on the Qcn file when editing , that is why I need Qcn file from my same phone to restore it

Moderator's Announcement: I had to slightly clean this thread. Please be aware that XDA does not allow any discussions or providing of tools regarding the change or the edit of IMEI's, only about restoring of original IMEI/EFS!

TheDarkKnight said:
I'm getting device not connected error in QFIL. Pls help
Click to expand...
Click to collapse
Qualcomm HS-USB Android it clearly shows ur device is connected

does it work on rog phone 2

qcn restore failed: the pointer passed in as a string must not be in the bottom 64k of the process's address space.
Please explaint and help here.

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i Cannot click on restore QCN please help!

Ravuri yaswanth said:
QCN FILE
Click to expand...
Click to collapse
i am having this issue with qpst tool

Would it work for Asus Zenfone 8 Flip? It has Qualcomm SM8350 Snapdragon 888 5G chipset with dual sim slot.

.backup file

Hello,
So my phone was stuck in bootloop and thus, I created a backup in my SD card. The files are shown as 13 files of 2GB size each with an extension ".backup" Anyone has any idea on how to combine these files and access the data inside on PC. The data is very important. Thank you!

deadmanspeaks said:
Hello,
So my phone was stuck in bootloop and thus, I created a backup in my SD card. The files are shown as 13 files of 2GB size each with an extension ".backup" Anyone has any idea on how to combine these files and access the data inside on PC. The data is very important. Thank you!
Click to expand...
Click to collapse
Crosspost from https://forum.xda-developers.com/t/moto-e4-plus-restart-loop.4241427/
I've had numerous Moto devices and have never seen any backup options in stock recovery., so I haven't any idea what format these are using.

readback stock recovery from SP Flash Tool and flash TWRP. also readback metadata partition (crypto footer). do not unlock bootloader because encryption is bonded to bootloader state. if you are lucky TWRP will work on locked bootloader. TWRP will decrypt your data so you can backup everything

aIecxs said:
readback stock recovery from SP Flash Tool and flash TWRP. also readback metadata partition (crypto footer). do not unlock bootloader because encryption is bonded to bootloader state. if you are lucky TWRP will work on locked bootloader. TWRP will decrypt your data so you can backup everything
Click to expand...
Click to collapse
How to do this? USB debugging and OEM are not ON in my phone. I saw some tutorial on YouTube, but it requires USB debugging.
Can't I use those userdata_*****.backup files?

usb-debugging is another option to access your data (can be enabled in boot.img)
SP Flash Tool is for preloader mode, no usb-debugging required
https://android.stackexchange.com/q/203283

wait, you did factory reset already? in that case crypto footer is reset too. backup is encrypted and therefore useless unless crypto-footer is restored.
you said you restored backup, are you sure? does the phone boot into lock screen like before and is pattern still the same?

aIecxs said:
wait, you did factory reset already? in that case crypto footer is reset too. backup is encrypted and therefore useless unless crypto-footer is restored.
you said you restored backup, are you sure? does the phone boot into lock screen like before and is pattern still the same?
Click to expand...
Click to collapse
Yes, the password is still the same. It's like the phone is again in the same condition with the same issue of boot loop.
I saw some tutorial on SP flash tool and what I did was:
1. Downloaded the SP flash tool
2. Downloaded TWRP recovery specific to my phone
3. Opened flash tool, went to download, clicked on scatter loading, selected the file and then clicked on download and connected my switched off device to the PC via USB
But, nothing happened after that.
My phone started charging, but nothing else happened.
I thought drivers weren't installed, so I went Driver Autoinstaller folders (there were 2 of them) and clicked on Driver Install, but it showed me this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then I clicked on finish and it showed this
When I went to the second folder, it showed me this
Is it because of this, that my device is not detected by this flash tool, and if yes, what can I do?

Yes it's driver issue. Disable driver signature enforcement and reboot. open device manager, connect phone and immediately select yellow triangle. install inf manually with let me pick option
you should not flash TWRP without a backup of stock recovery. Do a readback first. Also it is important the scatter file is matching your current partition layout. therefore you should analyze the result. if you are able to extract ramdisk with AIK then you have successfully dumped stock recovery (and can proceed with next step flashing twrp)

aIecxs said:
Yes it's driver issue. Disable driver signature enforcement and reboot. open device manager, connect phone and immediately select yellow triangle. install inf manually with let me pick option
you should not flash TWRP without a backup of stock recovery. Do a readback first. Also it is important the scatter file is matching your current partition layout. therefore you should analyze the result. if you are able to extract ramdisk with osm0sis' AIK then you have successfully dumped stock recovery (and can proceed with next step flashing twrp)
Click to expand...
Click to collapse
Understood before the readback thing. What is readback? I saw the tab in flash tools, but didn't get what it was? Can you please tell how to do that? (sorry for irritating, as I said I am a noob )
And how to analyse the result part? I didn't get the "extract ramdisk with osmosis AIK"
Is there any tutorial video that you know of, if yes, kindly send the link please coz I don't understand these terms.
And thanks a ton for this!!!

on readback tab delete all entries. add one entry for EMMC_USER. give meaningful file name recovery.img. enter length and start address in hex (refer to scatter file). start readback and connect phone.
Disable Antivirus program and download AIK. copy recovery.img into AIK directory and execute unpackimg.bat. enable Antivirus when done

aIecxs said:
on readback tab delete all entries. add one entry for EMMC_USER. give meaningful file name recovery.img. enter length and start address in hex (refer to scatter file). start readback and connect phone.
Disable Antivirus program and download AIK. copy recovery.img into AIK directory and execute unpackimg.bat. enable Antivirus when done
Click to expand...
Click to collapse
Okay, thank a ton!
I'll do all of this and get back to you.

aIecxs said:
on readback tab delete all entries. add one entry for EMMC_USER. give meaningful file name recovery.img. enter length and start address in hex (refer to scatter file). start readback and connect phone.
Disable Antivirus program and download AIK. copy recovery.img into AIK directory and execute unpackimg.bat. enable Antivirus when done
Click to expand...
Click to collapse
So, what length and start address am I supposed to enter in hex?
And you shared the link AIK, in that there are so many options, which one do I have to select?

What can I do now?

deadmanspeaks said:
So, what length and start address am I supposed to enter in hex?
Click to expand...
Click to collapse
refer to scatter file
check your model name owens (XT1774 XT1775 XT1776) or nicklaus (XT1771 XT1772 XT1773)
download scatter file matching to your device model
https://motostockrom.com/motorola-moto-e4-plus-xt1770
https://motostockrom.com/motorola-moto-e4-plus-xt1771-dual-sim
https://motostockrom.com/motorola-moto-e4-plus-xt1772
https://motostockrom.com/motorola-moto-e4-plus-xt1773
https://motostockrom.com/motorola-moto-e4-plus-xt1775
deadmanspeaks said:
And you shared the link AIK, in that there are so many options, which one do I have to select?
Click to expand...
Click to collapse
Android.Image.Kitchen.v3.7-Win32.zip
Code:
S_BROM_CMD_STARTCMD_FAIL (2005)
[BROM] can not pass bootrom start command! Possibly target power up too early.
deadmanspeaks said:
What can I do now?
Click to expand...
Click to collapse
pretty much self explaining.
why flash boot.img? are you sure that scatter matches your partition layout (you will erase wrong area if not)!?

aIecxs said:
refer to scatter file
View attachment 5281905
check your model name owens (XT1774 XT1775 XT1776) or nicklaus (XT1771 XT1772 XT1773)
download scatter file matching to your device model
https://motostockrom.com/motorola-moto-e4-plus-xt1770
https://motostockrom.com/motorola-moto-e4-plus-xt1771-dual-sim
https://motostockrom.com/motorola-moto-e4-plus-xt1772
https://motostockrom.com/motorola-moto-e4-plus-xt1773
https://motostockrom.com/motorola-moto-e4-plus-xt1775
Android.Image.Kitchen.v3.7-Win32.zip
Code:
S_BROM_CMD_STARTCMD_FAIL (2005)
[BROM] can not pass bootrom start command! Possibly target power up too early.
pretty much self explaining.
why flash boot.img? are you sure that scatter matches your partition layout (you will erase wrong area if not)!?
Click to expand...
Click to collapse
Thanks a lot here it is written nma26.42-169/300 and my phone is xt1770. The link you gave shows the file can't be downloaded, can you please give any other link. I googled the same, it gave me NMA26.42-169 INDIA something but those files are paid

drive.google.com links working fine to me

aIecxs said:
drive.google.com links working fine to me
Click to expand...
Click to collapse

tested all links. must be something about your country. you should get something like
Couldn't preview file. You may be offline or with limited connectivity.
click on -> Download
Google Drive can't scan this file for viruses
click on -> Download anyway

aIecxs said:
tested all links. must be something about your country. you should get something like
Couldn't preview file. You may be offline or with limited connectivity.
click on -> Download
Google Drive can't scan this file for viruses
click on -> Download anyway
Click to expand...
Click to collapse
Yes, I did that, after that only it shows this.
I am about to cry, it's been 14 months trying to get those files. Every time, I get too close and then bam! back to square one. Can't access those userdata***.backup files, can't access the phone, as soon as it starts, it gets stuck in a reboot loop, can't flash TWRP because not able to download the file. You have no idea how painful this is. Still thanks a lot, you helped me a lot, but I guess it's a lost cause now. Earlier lost the person, now lost the memories. Thanks anyways

deadmanspeaks said:
can't flash TWRP because not able to download the file.
Click to expand...
Click to collapse
https://twrp.me/motorola/motorolamotoe4plus.html

General [GUIDE][UNBRICK] Realme 8 Unbrick/Upgrade/Downgrade [RMX3085]

Hello everyone! So after the new MediaTek DAA and SLA protection bypasses you can find GitHub repo of here , using the bypass we are able to use SPFlash Tool, here is a guide how you can do it! This guide is for RMX3085 (Realme 8) ONLY. DON'T DO ANY OF THESE IF YOU HAVE SOMETHING ELSE!
ALWAYS USE DOWNLOAD ONLY MODE OF SP FLASH TOOL.
DON'T TOUCH ANYTHING RELATED TO FORMAT ON SP FLASH TOOL! (IT'S WRITTEN EVERYWHERE, YOU WILL LOSE YOUR IMEIS IF YOU USE FORMAT ALL + DOWNLOAD. YOU ARE SAFE IF YOU USE DOWNLOAD ONLY.)
Requirements:
PC or Laptop
Internet connection
Realme 8
USB cable
Windows Method
Requirements:
Bypass Tools Pack - (DRIVER AND BYPASS FILES)
SP Flash Tool
Decrypted OFP (OPPO FIRMWARE PACKAGE) :
Indian
A.22 (Indian) - GDrive
A.24 (Indian) - GDrive
A.26 (Indian) - Gdrive
C.05 (Indian) - GDrive
C.09 (Indian) - GDrive
C.11 (Indian) - GDrive
Global
A.22 (Global) - GDrive
A.24 (Global) - GDrive
A.26 (Global) - GDrive
Install Python from Windows Store
libusb-win32 - Having Issues? Use this.
Get usbdk installer (.msi) from here and install it
Steps:
1) Extract the zip
2) Go to driver folder, find the .inf file right click and press install.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3) Download this file and install it, after installing power off phone and connect to pc while holding Vol+- (don't leave the buttons after connecting) . You might need this driver as well if it's not detected.
4) Press next, connect your device to PC while holding Vol+- buttons (your device needs to be powered off, and don't leave the buttons) and you will see the mtkdriver down below. Install it.
5) Choose MediaTek USB Port and install it.
6) Then run the brom.bat under Bypass folder.
7) Now power off the phone and connect the phone while holding volume + and - (Don't leave the buttons until the bypass is done)
8) After the above step Go into Flash Tool folder and open the SPFlash tool go to Options>Option
9) Click on Connections and select UART and set Baud Rate to 921600
10) After that choose scatter file and also if not set, set your download-agent. You don't need to select auth file as authorization is disabled. Once you do it, it should look like this. ALWAYS MAKE SURE DOWNLOAD ONLY MODE IS SELECTED! DON'T SELECT OTHER MODES!
Select all the Partitions except opporeserve2 and cdt_engineering. otherwise you will get errors.
*11) If you want to flash super.img partition also then download this scatter.txt file and replace it with the another scatter file which is present in the decrypted firmware folder. After that select it again in sp flash tool.
Again Make SURE "Download Only" is selected. Don't select ANYTHING ELSE! You will lose your IMEIs, Serial Numbers, Capability of Hardware Attestation etc. if you choose "Format data + Download" make SURE you selected "Download Only".
Now, you can start downloading with the button and after that a checkmark will appear. You can reboot your phone and use it like before now! All your userdata will (inevitably) be cleared!
After flashing it should look like this. Download has been complete. Enjoy!
"Congrats Now your Realme 8 is Unbricked "
Credits :
https://github.com/bkerler/ for decryptor and for creating the tool.
If you face any issues write them down below...

Some people having this problem so I want to add one more thing to the guide. If you are not having any issues related to boot then don't follow these steps.
After waiting more then 10 minutes, if it doesn't boot up/bootloop. Or shows DM-Verity corrupt error then do this.
1) Try boot into stock recovery by pressing volume up + power button after that when your screen flashes quickly unpress buttons.
2) Now press volume down + power button, by pressing these you will boot into stock recovery.
3) Go to format option and do a full format.
4) Your phone will definitely boot up after that.

Hi
I would like to ask how you obtained the system for realme 8 in the latest version.
Can you download somehow from your device?

HowWof said:
Hi
I would like to ask how you obtained the system for realme 8 in the latest version.
Can you download somehow from your device?
Click to expand...
Click to collapse
From realme offical site

Could you send a link because there is no information on the Polish realme site

HowWof said:
Could you send a link because there is no information on the Polish realme site
Click to expand...
Click to collapse
Realme 8 Firmware (RMX3085) - Realme Firmware
Realme 8 Firmware RMX3085 Official Flash File (Stock ROM). flash your phone using realme flashtool or MSM Download tool.
realmefirmware.com

if "Brick" occured in rooting process - then can recovery be done without data loss :
Prerequisite: firmware version on the body must the same as downloaded "Decrypted OFP" (as example both is A.22 )
HowTo:
at step of SPFlashing (currently that is 10-th)
- check ONLY next partitions in SPFlash to restore :
PRELOADER RECOVERY VBMETA LK LK2 BOOT
... and NO any of other
(as thats only are touched by currently described rooting processes)

after recovery exist on every boot:
"dm-verify corrupted..."
how to get out of this message?
Reset with clearing data not helps ...

DaLiV said:
after recovery exist on every boot:
"dm-verify corrupted..."
how to get out of this message?
Reset with clearing data not helps ...
Click to expand...
Click to collapse
Wait for 10mins if it didn't boot then.
Format with mtk client
python mtk e metadata,userdata,md_udc

that boots ... BUT
on every boot thet alerts about "corruption"
ok cleared partitions with python...
still the same alert ...

DaLiV said:
that boots ... BUT
on every boot thet alerts about "corruption"
ok cleared partitions with python...
still the same alert ...
Click to expand...
Click to collapse
Try booting into stock recovery and format from there

Ok. format from recovery menu solves ...
now that boots normally =
- no alert
-no boot allowing by pressing key required
good behaviour to see when boot subsystem altered, as at every boot alerted and required to press longer power button to confirm/allow starting ...
interesting, that is something new on mine (device versions) or overall ...

I have it anyway. have you solved it yet? Do I understand correctly?

after doing the insstruction, mine bootlooping and enters recovery mode

XCentrialG said:
after doing the insstruction, mine bootlooping and enters recovery mode
Click to expand...
Click to collapse
Maybe you missed some step. Can u explain ur problem briefly. What u did and what happened.

niki.rsb said:
I have it anyway. have you solved it yet? Do I understand correctly?
Click to expand...
Click to collapse
I Think that is not so solvable /possible if someone decode debug and finds /... but that is quite acceptable for rooting /if you don't want to make illegal spionage and so on/ ... also as if your device will be rooted by someone - you will see alert of changes on boot ... that is good ...
if you are rooted - you must be alerted .
but if you will going to stock rom and have protection - then flashing "stock" (surely without 3 partitions that IMEI-and-so-on-related ) and then format from recovery menu helps return to "factory" operation

Tony Stark said:
Maybe you missed some step. Can u explain ur problem briefly. What u did and what happened.
Click to expand...
Click to collapse
just a casual day to update my firmware, reboot and my phone refused to boot anymore, and then i came here, following all the steps very carefully (i read every steps twice so i dont make any mistake), and no luck.

XCentrialG said:
just a casual day to update my firmware, reboot and my phone refused to boot anymore, and then i came here, following all the steps very carefully (i read every steps twice so i dont make any mistake), and no luck.
Click to expand...
Click to collapse
There should be some mistake in your process. Because this guide is working and tested by many people.

Does global firmware have realme dialer instead of google dialer?
Can I flash Global firmware my indian device?

on your firmware package, it does not flashes super.img by default. Because in scatter file
- partition_index: SYS48
partition_name: super
file_name: super.img
is_download: false
changing false to true helps fixing destroyed super partition