Wrong CWM Hardbicked? - Galaxy Ace S5830 Q&A, Help & Troubleshooting

Hi i have made a very bad mistake and have installed CWM intended for the 5830i on my 5830 the phone turned off straight away.
Now it will not boot looks dead.
I can get into download mode odin detects it but i cannot see anything on my screen. Then when i start odin i get to:
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
That's it, just hangs there.
Is my 5830 hardbricked?
Is there a way around it?
Would a jig be of any benefit?
[email protected]

Do you have the required drivers?
Wrong recoveries usually hard brick the phone but you might be lucky
le random signature o.o

Yes i have all the drivers. I hope im lucky stressed to max now.

[email protected] said:
Yes i have all the drivers. I hope im lucky stressed to max now.
Click to expand...
Click to collapse
If you press the download mode buttons
Does it say downloading ?
If not it can be that you have killed your ace aka hardbricked
Sent from my ST25i using xda app-developers app

No nothing just blank screen. So it was probably Emergency Download Mode? Hardbricked? I will try a few phone shops by me see if they got a riff box.

[email protected] said:
Hi i have made a very bad mistake and have installed CWM intended for the 5830i on my 5830 the phone turned off straight away.
Now it will not boot looks dead.
I can get into download mode odin detects it but i cannot see anything on my screen. Then when i start odin i get to:
StartThread Detected : 0
StartThread Detected : 0
StartThread Detected : 0
StartThread Detected : 0
setup connection...
That's it, just hangs there.
Is my 5830 hardbricked?
Is there a way around it?
Would a jig be of any benefit?
[email protected]
Click to expand...
Click to collapse
Try this Odin & cooper:-
http://db.tt/jgXJcjzG
Do press thnks!!
Sent Via XDA™ Premium

Galaxy_Rohit said:
Try this Odin & cooper:-
http://db.tt/jgXJcjzG
Do press thnks!!
Sent Via XDA™ Premium
Click to expand...
Click to collapse
Thanks for the input but still the same stuck on:
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
I am using S5830BUKS2_S5830VODKS1_S5830XWKS2_HOME.tar.md5 one package file. That is the stock that it was on originally.
I have been looking for a multipackage to try anybody got a link?
Also i uninstalled kies and re installed now i have "SAMSUNG CDMA Technologies" in device manager without drivers and i cannot for the life of me get drivers to install.
CDMA? that's USA aint it? I'm UK GSM?

If the download mode doesn't come up with the words downloading, written, then your device is hard bricked and you have to take your phone to a service center
le random signature o.o

Prawesome said:
If the download mode doesn't come up with the words downloading, written, then your device is hard bricked and you have to take your phone to a service center
le random signature o.o
Click to expand...
Click to collapse
No warrenty left on the brick.
Riff Box will do it so i will go to phone shop thanks for your help.

[email protected] said:
No warrenty left on the brick.
Riff Box will do it so i will go to phone shop thanks for your help.
Click to expand...
Click to collapse
Hey it had happened to me too
do this
Reinstall smasung drivers and then try flash via Odin it will surely work ...
And in that joy don't forget to come back and hit thanks lol
__________________________________________
"lts not who u r inside, its wat u do that defines u..."
———–——————————————
--->make ur phone faster and more battery efficient
--->partition and link apps to sd?!?!?
--->cool 3d games for galaxy y (no root no lag)

sanny5 you saying you flashed cwm meant for a 5830i on a 5830? And you unbricked it like that?

[email protected] said:
No warrenty left on the brick.
Riff Box will do it so i will go to phone shop thanks for your help.
Click to expand...
Click to collapse
Well, if Odin doesn't work and the download mode doesn't come up, then its a certain hard brick. Nothing you can do except service center or jtag
P.S. for God's sake, stop begging for thanks people
le random signature o.o

THANKS
Galaxy_Rohit said:
Try this Odin & cooper:-
Do press thnks!!
Sent Via XDA™ Premium
Click to expand...
Click to collapse
Thanks!! I had the freakin' same problem (caused by a power voltage problem while flashing) and thanks to you, my Ace's back!!!

Did you have Download on screen?

arc4d14n said:
Thanks!! I had the freakin' same problem (caused by a power voltage problem while flashing) and thanks to you, my Ace's back!!!
Click to expand...
Click to collapse
You're always welcome...
Sent Via XDA™ Premium

[email protected] said:
Did you have Download on screen?
Click to expand...
Click to collapse
Yes, It was pretty much the only thing that my display shown....

Me too need
@gelexy Rohit Please give me this OPS & odin .. my S5830 also bricked
i tried to download from Google Drop box bot error 404 file not found there .
please give me new link
Br
Tarun

[email protected] said:
Hi i have made a very bad mistake and have installed CWM intended for the 5830i on my 5830 the phone turned off straight away.
Now it will not boot looks dead.
I can get into download mode odin detects it but i cannot see anything on my screen. Then when i start odin i get to:
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
That's it, just hangs there.
Is my 5830 hardbricked?
Is there a way around it?
Would a jig be of any benefit?
[email protected]
Click to expand...
Click to collapse
Hi There,
Try reinstaaling the Drivers or updating then or swap the Odin version if no sucess. Then Try Usb Jigg

Related

[Q] Odin stuck at: <1> setup connection...

​I have a Samsung Galaxy Ace GT-S5830, with the following info:
- Android Version: 2.2.1
- Baseband Version: S5830JXKC1
- Kernel Version: 2.6.32.9-perf
- Build Number: Froyo.JPKC2
- Connected to a Laptop running Windows 7 Enterprise fully updated with hotfixes, updates and drivers.
I’m tying to Install the new gingerbread 2.3.4 update from samfirmware, but every time I run Odin and try to update, the process stops at: <1> setup connection...
I tried to:
- Use a different laptop.
- Use a different cable.
- Use a newer version of Odin (old was 4.38, new is 4.42).
- Kill the Kies processes in my laptop using task manager.
- Update Kies to the latest version.
- Uninstall Kies and it's related files.
- Update my laptop motherboard and USB drivers.
- Reinstall the Samsung Mobile Phone USB drivers.
- Select different settings in Odin (Debugging mode / PDA mode... etc).
none of the above worked
help?
If you did this question may sound stupid but I should ask anyway...
Did you boot to download mode?
How to put into download mode
1. On an OFF state, press VolumeDown+HomeButon+Powerbutton (hold them together until you see the download mode screen (small yellowish/gold/orange color)
Hope we were able to help you.
It worked
Okay, your question was not stupid, I do feel stupid however :/ apparently I was doing this:
- Holding Down Volume Up + Volume Down + Home Button + Power Button!
It loads a screen that says "Emergency Download Mode", which I assumed was the correct loading screen since it does show on Odin...
I was wrong; I should have just done this:
- Holding down Volume Down + Home Button + Power Button!
In which it does load the correct download screen with the yellowish message that say "Downloading…"
Thanks a million guys, this one gave me a heart attack yesterday
I have problem upgrading my Ace too,
I have a yellow text showing downloading and I always got stuck :
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> --- cannot open the usb serial port. code: 32
can someone advise?
Thanks
Something is messed up with your PC's USB drivers. Get an updated set of your Chipset drivers for your motherboard, uninstall and reinstall Kies, or switch to a different PC.
ronlkh said:
I have problem upgrading my Ace too,
I have a yellow text showing downloading and I always got stuck :
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> --- cannot open the usb serial port. code: 32
can someone advise?
Thanks
Click to expand...
Click to collapse
Hey!
Just wanted to ask, dose you in "DOWNLOAD" mode?
CHEERS!
casiocas said:
Hey!
Just wanted to ask, dose you in "DOWNLOAD" mode?
CHEERS!
Click to expand...
Click to collapse
There's startthread detected. It means he was in the download mode before it messes up.
consegregate said:
There's startthread detected. It means he was in the download mode before it messes up.
Click to expand...
Click to collapse
Hey!
Jeah, he has problem with USB(drivers or change to other USB).
CHEERS!
Thanks to everyone who gives their advice.
Finally the problem is from the PC, probably some USB device clash with odin. After using another PC, I am able to flash my ace now.
Thanks again.
Noorish said:
Thanks a million guys, this one gave me a heart attack yesterday
Click to expand...
Click to collapse
He heartattack no good and unnecassary use 'JIG' to recover allways..
http://www.youtube.com/watch?v=Rdn5GoRjhn0
Noorish said:
Okay, your question was not stupid, I do feel stupid however :/ apparently I was doing this:
- Holding Down Volume Up + Volume Down + Home Button + Power Button!
It loads a screen that says "Emergency Download Mode", which I assumed was the correct loading screen since it does show on Odin...
I was wrong; I should have just done this:
- Holding down Volume Down + Home Button + Power Button!
In which it does load the correct download screen with the yellowish message that say "Downloading…"
Thanks a million guys, this one gave me a heart attack yesterday
Click to expand...
Click to collapse
I'm having the same problem. I'm trying to unbrick my Ace phone. The problem is that nothing comes up on the screen and I can only access EMERGENCY DOWNLOAD MODE (pushing all the buttons). I can NOT enter normal DOWNLOAD MODE the phone just doesn't enter this mode and Odin does not recognize it. Should ODIN work also on EMERGENCY DOWNLOAD MODE? or just DOWNLOAD MODE? if so, how can I get to DOWNLOAD MODE?? HELP PLZ!!!!
pliundemix said:
I'm having the same problem. I'm trying to unbrick my Ace phone. The problem is that nothing comes up on the screen and I can only access EMERGENCY DOWNLOAD MODE (pushing all the buttons). I can NOT enter normal DOWNLOAD MODE the phone just doesn't enter this mode and Odin does not recognize it. Should ODIN work also on EMERGENCY DOWNLOAD MODE? or just DOWNLOAD MODE? if so, how can I get to DOWNLOAD MODE?? HELP PLZ!!!!
Click to expand...
Click to collapse
Use a USB Jig
Sent from my GT-S5830 using XDA App
this is Siddhartha,i am using Samsung galaxy ace & i
have rooted my phone then by using titanium back up i had deleted some
app;s in my phone then i tried to back up by ROM MANAGER finally i got
bricked my phone ....... plz help me out from this problem
i had tried to unbrick by odin multi down loader by stock ROM
Odin 4.38 detect phone ok but always get this error:-
Download Start...
<0> Create File...
<1> StartThread Detected : 0
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 1
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> : 0
<4> setup connection...
why u used rom manager dude.........................................................................
send to ur service center....................................................................................
http://forum.xda-developers.com/archive/index.php/t-1342569.html
i have the same problem
FinnAndJake said:
why u used rom manager dude.........................................................................
send to ur service center....................................................................................
http://forum.xda-developers.com/archive/index.php/t-1342569.html
Click to expand...
Click to collapse
odin recognizes my phone but only in emergency download mode not the download mode and im stuck at step 1 setting up conn. what is emergency download for if not to unbrick your phone wtf and my 1click unsoft brick keeps failing too if anyone knows how to do it videos are useless if it just shows success not failures and what to do
I got the same problem it stucks to setup connection. The strange is when i try entering download mode it doesnt go with the yellow Downloading stuff. It apears a square on top in it saying Emergency Dload Mode (ARM9 mode) and lower from the square the samsung logo. I have a samsung galaxy mini GT-S5570. Anny help?
sica0 said:
I got the same problem it stucks to setup connection. The strange is when i try entering download mode it doesnt go with the yellow Downloading stuff. It apears a square on top in it saying Emergency Dload Mode (ARM9 mode) and lower from the square the samsung logo. I have a samsung galaxy mini GT-S5570. Anny help?
Click to expand...
Click to collapse
Look at this video
http://www.youtube.com/watch?v=LqaijoQGE_I
I know what your problem is your friend try to move your usb plugs into the other ...
:highfive:
ronlkh said:
I have problem upgrading my Ace too,
I have a yellow text showing downloading and I always got stuck :
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> --- cannot open the usb serial port. code: 32
can someone advise?
Thanks
Click to expand...
Click to collapse
Hope u guys know the correct name of the ops file of the respective phone. Nearly half of the issues have been solved just by renaming the ops file.
But there are some more critical cases too:sly:

[Q] HELP!!!! bricked after 'Flashing the Recovery' with ROM Manager - Galaxy MINI

My phone got bricked after Flashing ClockWorkMOD using ROM Manager.
It seems to be a hard brick; No display, don't know if its charging, but when 'VOL UP, VOL DOWN, HOME & POWER' (I think it goes to 'Emergency Download Mode' but the screen is off) is pressed, the PC detects it and shows the 1st Image below. Odin detects it as like the Image 2 below. But gets STUCK like the 3rd image and I've also attached the message that ODIN gives!
Please help Thanks!!!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
<1> Added!!!
<1> Detected!!!
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
Click to expand...
Click to collapse
Rtry using odin ...The first two steps are right (I think...).Also try using a different version like DDKQ7...And never use ROM MANAGER .
Sent from my GT-S5570 using xda premium
Kaustubh_93 said:
Rtry using odin ...The first two steps are right (I think...).Also try using a different version like DDKQ7...And never use ROM MANAGER .
Sent from my GT-S5570 using xda premium
Click to expand...
Click to collapse
Never using ROM Manager again once is enough!!!! Phhh!
If you want me to use different firmwares then i've tried it but if you want me to do something else then please elaborate. Thanks.
I think I need to find a way to get ODIN to be in good contact with my phone!
I've got Ubuntu, if it would help I could use it! Cuz I see developers using it on youtube, and Ubuntu & Android are both Linux Based!!!
i had similar promlem, stuck on connection and it was usb problem.Try on some other pc
haneef95 said:
My phone got bricked after Flashing ClockWorkMOD using ROM Manager.
It seems to be a hard brick; No display, don't know if its charging, but when 'VOL UP, VOL DOWN, HOME & POWER' (I think it goes to 'Emergency Download Mode' but the screen is off) is pressed, the PC detects it and shows the 1st Image below. Odin detects it as like the Image 2 below. But gets STUCK like the 3rd image and I've also attached the message that ODIN gives!
Please help Thanks!!!
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1255305
pull out your battery . .
wait 10sec
press ON . HOME BUTTON and VOLUME DOWN
while holding put back you battery . .
then it will go back on downloading
need use first method . .
one solution
Your phone is hard bricked. bootloader wrong.phone cannot boot.
Go to service center and talk fake story . if you lucky , wanarity center will acpect your phone
had same problem
My galaxy mini was also bricked by rom manager tried all solutions an looked into jig method i had warrant so told samsung was syncing with keys and all went dead theye fixed an had it back to me in 10 days with a letter saying they found the problem and fixed also installed latrst firmware witch was froyo this was a o2 locked phone witch i can also confirm u can flash with gingerbread then any custom rom for our minis. Now using emanon v4 removed rom manager as sgalaxy mini is not supported
unfortunately there's no solution but sending it to the technical service
I think you should go to a service center.
Sent from my GT-S5570 using xda premium
Done!
Thanks Guys, Matter sorted.
Went to the shop and they replaced the phone! )

TWRP Bootloop [FIXED]

Howdy all,
Got a wee tiny problem here. I had recently decided to update my recovery mode to TWRP to allow me to perform backups of my system as i am not fully trusting of technology and ran into a wee roadblock. My phone is now stuck in a bootloop to recovery mood, well i did some digging online and found a few guides to fixing this issue. All the guides require me to use odin which for some reason does not work on my computer, everytime i try to use it i get an error message of:
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> --- cannot open the usb serial port. code: 32
So again i went digging online and found a few fixes uninstalled the nokia suite on the computer, disabled the kies service on startup, made sure it wasn't in my running processes, tried every USB port, tried numerous reboots and all to no avail.
I don't have access to another computer to be able to run odin on and i absolutley need my phone.
So can anyone on here help me, im going stir crazy and have ran short of ideas for fixing
Mucho Gracias
http://forum.xda-developers.com/showthread.php?t=1431721
or
http://www.sammobile.com/forum/showthread.php?t=1046
Some solutions:
- Delete odin
- Clean Registery (sometimes it works)
- Delete KIES and reboot pc. Delete any file regardin to KIES!!
- Reinstall only the Samsung USB drivers: http://forum.xda-developers.com/showthread.php?t=961956
- Open Odin with admin rights and try again
- Use another PC
Good Luck
Thanks for the advice after 9 hours i finally got it working. It took me copying the folder i was trying to use onto my E:/ drive and then to run it from there.

[Q] Lg P970 Optimus Black Huge Problem

Hi all,
I have two Lg Optimus Black. One of them i already use for 6 mounts and i can update or flash it by using SmartFlashTool easily.
Second phone which i bought unfortunately from ebay, when i get it 1 mounth ago, i try to flash it. I done. Then i try to root it,but i couldnt and it bricked.
Now last one mounth i try to flash it again,again,again.. i have always strange problem.. Last rom - which i flashed before try to root- was V20_D..
Now, i try to flash it to v30 or v20 or v10, after finish flashing phone doesnt restart. I take out battery, then put it back. After this,phone geting start..
But, it starting again with V20_D..
When i try to save any contact or changing some settings on the phone, after restart, it start again like factory reset..
I checked on hidden menu (3845#*970#) firt menu VERSION INFO...
SW Version is V20_D but factory version is changing depens on which rom i flashed last..(V10 or V30 or V20)
I checked same thing also on my other P970, this two version is same..
I could do everything easily and properly on other P970..
Do you have any idea? What is the problem ? What can i do ?
ozkanyanik said:
Hi all,
I have two Lg Optimus Black. One of them i already use for 6 mounts and i can update or flash it by using SmartFlashTool easily.
Second phone which i bought unfortunately from ebay, when i get it 1 mounth ago, i try to flash it. I done. Then i try to root it,but i couldnt and it bricked.
Now last one mounth i try to flash it again,again,again.. i have always strange problem.. Last rom - which i flashed before try to root- was V20_D..
Now, i try to flash it to v30 or v20 or v10, after finish flashing phone doesnt restart. I take out battery, then put it back. After this,phone geting start..
But, it starting again with V20_D..
When i try to save any contact or changing some settings on the phone, after restart, it start again like factory reset..
I checked on hidden menu (3845#*970#) firt menu VERSION INFO...
SW Version is V20_D but factory version is changing depens on which rom i flashed last..(V10 or V30 or V20)
I checked same thing also on my other P970, this two version is same..
I could do everything easily and properly on other P970..
Do you have any idea? What is the problem ? What can i do ?
Click to expand...
Click to collapse
first of all you didnt read the rules , post in q\a section , secondly make sure its a p970 not a p970h or ku9500 , if its a p970 download any rooted cwm rom such as this and flash it , then you should be fine
Sorry for rules
rrgrrg said:
first of all you didnt read the rules , post in q\a section , secondly make sure its a p970 not a p970h or ku9500 , if its a p970 download any rooted cwm rom such as this and flash it , then you should be fine
Click to expand...
Click to collapse
Thanks for reply.. Yes you are right, i didnt read the rules. Sory about that..
And second, as i can see under the battery, it is writing P970..
So, it should be P970..
Is there any way else to learn which one it is ?
ozkanyanik said:
Thanks for reply.. Yes you are right, i didnt read the rules. Sory about that..
And second, as i can see under the battery, it is writing P970..
So, it should be P970..
Is there any way else to learn which one it is ?
Click to expand...
Click to collapse
this should be enought
rrgrrg said:
first of all you didnt read the rules , post in q\a section , secondly make sure its a p970 not a p970h or ku9500 , if its a p970 download any rooted cwm rom such as this and flash it , then you should be fine
Click to expand...
Click to collapse
Btw P970 and p970h roms are interchangeable. It doesn't matter if ROM is for Fra, EU (p970) or Mex, Bra (p970h) you can install one from p970 on a p970h and vice versa.
sent from my Optimus Black V28c
Reboot recovery
rrgrrg said:
this should be enought
Click to expand...
Click to collapse
Ok, but how can i reboot recovery now? Phone doesnt boot in recovery mode..
ozkanyanik said:
Ok, but how can i reboot recovery now? Phone doesnt boot in recovery mode..
Click to expand...
Click to collapse
Have you installed ROM manager, and inside ROM manager install alternative recovery then you can reboot in recovery.
sent from my Optimus Black V28c
re4lsk said:
Have you installed ROM manager, and inside ROM manager install alternative recovery then you can reboot in recovery.
sent from my Optimus Black V28c
Click to expand...
Click to collapse
Sorry, but i think you didnt read my main post..
Even i flash any different patched or custom rom , it start again with V20d rom..
I tried on different computer.. i tried to reinstall all usb and other drivers.. I download different SFT and tried with this...
I download different rom and tried with this..
After all, it seems like nothing happens after flashing..
So, when i flash any patched rom now, i can not reach to recovery mode..
And today i notice something else.. After flashing i tried to factory reset from settings menu.. it doesnt work.. I push button but nothing happends.And phone can not return to desktop (home)
ozkanyanik said:
Sorry, but i think you didnt read my main post..
Even i flash any different patched or custom rom , it start again with V20d rom..
I tried on different computer.. i tried to reinstall all usb and other drivers.. I download different SFT and tried with this...
I download different rom and tried with this..
After all, it seems like nothing happens after flashing..
So, when i flash any patched rom now, i can not reach to recovery mode..
And today i notice something else.. After flashing i tried to factory reset from settings menu.. it doesnt work.. I push button but nothing happends.And phone can not return to desktop (home)
Click to expand...
Click to collapse
To me it looks like your phone is read only. Can you please set up adb (one package is in my noob how to) the type: adb shell
Then type: mount
And post the output here.
Either this or the connection between your pc and your phone doesnt work for any other reason...
Sent from my LG-P970 using xda app-developers app
N00BY0815 said:
To me it looks like your phone is read only. Can you please set up adb (one package is in my noob how to) the type: adb shell
Then type: mount
And post the output here.
Either this or the connection between your pc and your phone doesnt work for any other reason...
Sent from my LG-P970 using xda app-developers app
Click to expand...
Click to collapse
$ su
su
su: permission denied
$ mount
mount
rootfs / rootfs ro,relatime 0 0
tmpfs /dev tmpfs rw,relatime,mode=755 0 0
devpts /dev/pts devpts rw,relatime,mode=600 0 0
proc /proc proc rw,relatime 0 0
sysfs /sys sysfs rw,relatime 0 0
none /acct cgroup rw,relatime,cpuacct 0 0
tmpfs /sqlite_stmt_journals tmpfs rw,relatime,size=4096k 0 0
tmpfs /mnt/asec tmpfs rw,relatime,mode=755,gid=1000 0 0
tmpfs /mnt/obb tmpfs rw,relatime,mode=755,gid=1000 0 0
none /dev/cpuctl cgroup rw,relatime,cpu 0 0
/dev/block/mmcblk0p8 /system ext3 ro,nodev,noatime,barrier=0,data=writeback 0 0
/dev/block/mmcblk0p9 /data ext3 rw,nosuid,nodev,relatime,errors=continue,barrier
=0,data=writeback 0 0
/dev/block/mmcblk0p6 /dvp/hwkey ext3 rw,nosuid,nodev,relatime,barrier=1,data=wri
teback 0 0
/dev/block/mmcblk0p6 /dvp/userdata ext3 rw,nosuid,nodev,relatime,barrier=1,data=
writeback 0 0
debugfs /sys/kernel/debug debugfs rw,relatime 0 0
/dev/block/mmcblk0p5 /lgdrm ext3 rw,nosuid,nodev,relatime,errors=continue,barrie
r=0,data=writeback 0 0
$ su
I checked from England LG Service for my P970 by using imei number and serial number.. And the answer is there is no record for this numbers..
They said it can be copy or fake LG optimus black..
Now i am trying to do something on adb server..
But after all commands after i write, phone says read only file system..
I can not wipe all data, or delete something..
((
Hi ozkan can you check your phone on this web site with your imei?
http://csmg.lgmobile.com:9002/csmg/b2c/client/auth_model_check2.jsp?esn=IMEI
Delete IMEI at the last word of the link and write your phone imei on there.And you can see your phone model and latest firmware verion number.If your phone has fake imei you will see nothing.
George Jetson said:
Hi ozkan can you check your phone on this web site with your imei?
http://csmg.lgmobile.com:9002/csmg/b2c/client/auth_model_check2.jsp?esn=IMEI
Delete IMEI at the last word of the link and write your phone imei on there.And you can see your phone model and latest firmware verion number.If your phone has fake imei you will see nothing.
Click to expand...
Click to collapse
Hi George, there is nothing open on the link.. Can you check the link please is it working or not..
ozkanyanik said:
Hi George, there is nothing open on the link.. Can you check the link please is it working or not..
Click to expand...
Click to collapse
Its working i tried it already.
You just have to DELETE the IMEI and INPUT your Phone's Imei Number.
from this
http://csmg.lgmobile.com:9002/csmg/b...2.jsp?esn=IMEI
to this
http://csmg.lgmobile.com:9002/csmg/b...2.jsp?esn=xxxx
Key in your IMEI (the "x" is where u Key in your IMEI)
its 100% working

[SOLVED] Galaxy Ace S5830 - Soft Brick - Need help!

Heya Guys,
So I had been playing with my Galaxy Ace recently, and I managed to Soft brick it.
But unfortunately I cannot seem to recover it.
What happened:
I had rooted my OFW and decided to try Cyanogenmod 7.2. All was going well.
Then I read about this firmware; http://michielv.eu/2012/10/12/boost-your-samsung-galaxy-ace-s5830i/
M!-U! Rom, so I looked it up on XDA and found 2.2.1patched, and flash that.
On reboot I got a black screen. No boot. OH ****!
I did find if I do the battery trick I can get into download mode. Screen still black.
The problems is I cannot flash ANYTHING using Odin. (tried 1.85 & 4.38 on 2x Win7 machines & 1x XP machine)
Odin recognizes the phone in download mode (Yellow square) but when I try to flash, it gets stuck on
"<>1 Setup Connection"
Tried updating the Samsung drivers and using different ports, nothing is working.
Tried a USB Dongle, no luck.
I do have a full CWM backup on the SD, but I cannot get into recovery mode.
If anyone has any ideas on how to get Odin working (I'm on a Win7 machine) I'd really appreciate it..
Thanks,
Brik
Maybe Odin is outdated. Also did you check the one package option in Odin while flashing? Also, try using a different USB cable. Try this website- androidadvices.com....go to the galaxy ace section and follow the steps EXACTLY.
If everything fails, go to a service centre and say that your device got bricked while updating from kies.... You need to appear very angry and absolutely convinced that it's not your fault. Then they'll probably repair it.
Best if luck.
Swyped from My Galaxy Ace.
A thanks would be appreciated.
Kabir Saxena said:
Maybe Odin is outdated. Also did you check the one package option in Odin while flashing? Also, try using a different USB cable. Try this website- androidadvices.com....go to the galaxy ace section and follow the steps EXACTLY.
If everything fails, go to a service centre and say that your device got bricked while updating from kies.... You need to appear very angry and absolutely convinced that it's not your fault. Then they'll probably repair it.
Best if luck.
Swyped from My Galaxy Ace.
A thanks would be appreciated.
Click to expand...
Click to collapse
Thanks for the reply! I've used Odin v4.38 & v4.42 (those recommended for S5830) and even tried 1.85 and 3.07.
None work. Tried a different cable and that didn't work either.
Can you provide an direct link to androiddevices.com? No sure what "Steps" I should look at..
If I have no luck by Monday, I'll take it back..
Thanks!
BrikHaus said:
Thanks for the reply! I've used Odin v4.38 & v4.42 (those recommended for S5830) and even tried 1.85 and 3.07.
None work. Tried a different cable and that didn't work either.
Can you provide an direct link to androiddevices.com? No sure what "Steps" I should look at..
If I have no luck by Monday, I'll take it back..
Thanks!
Click to expand...
Click to collapse
Here is a link to the mobile website- http://androidadvices.com/update-galaxy-ace-s5830-official-gingerbread-236-xwktm-firmware/
Tty this. And download the files from this website itself. The site is trustworthy.
Kabir Saxena said:
Here is a link to the mobile website- http://androidadvices.com/update-galaxy-ace-s5830-official-gingerbread-236-xwktm-firmware/
Tty this. And download the files from this website itself. The site is trustworthy.
Click to expand...
Click to collapse
This is exactly what I've been doing; But Odin gets stuck and wont let me flash;
Code:
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
BrikHaus said:
This is exactly what I've been doing; But Odin gets stuck and wont let me flash;
Code:
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
Click to expand...
Click to collapse
Well, do you have any firewalls on your computer? If yes, disable them. They sometimes interfere with Odin.
Kabir Saxena said:
Well, do you have any firewalls on your computer? If yes, disable them. They sometimes interfere with Odin.
Click to expand...
Click to collapse
Tried that but still no luck.
It seems I can get into "Emergency Recovery Mode" (Up+Down+Home+Power) Only. Cannot get download mode,,
Odin still recognises the phone (yellow square) but will not flash...
Ok, since I couldn't get it into download mode I returned the phone to place of purchase and got a replacement.
Problem solved.
BrikHaus said:
Ok, since I couldn't get it into download mode I returned the phone to place of purchase and got a replacement.
Problem solved.
Click to expand...
Click to collapse
Good to hear.
Many are not as lucky as you.

Categories

Resources